Did @bootmod3 add an e30 OTS map for the BMW S63tu M5/M6 in version 2.0? Great content, awesome product; I am looking forward to expanding use of BM3 for my all BMW's.
What is the difference for the X3M? I and two other members have installed it same as the video and cannot get the sensor to read. This is extremely frustrating.
If yours is a pre-LCI model the controller may need a firmware change that simply stitches the CANBus msg id from 0xEC to 0xED lile what’s done for Gen1 G series cars. It was recently discovered that some preLCI X3M/X4M cars already use 0xEC already so it was necessary to move it over. Contact support@protuningfreaks.com and they’ll advise accordingly.
@jakrieg did you ever figure out the solution im dealing with this right now too. You would think they would have info out about this so we dont tap into random wires 😒
I have a 2020 x3m and i cant figure out what wire i tap in to i tired con3 pin 1 and it doesnt work it actually turned my cluster off while driving. Do you know the location of the ignition wire for the 2020 x3m?
When I followed the steps for draining the fuel line on my m340, in both install and removal the fuel lines never got drained and it would spray gas everywhere. Car would run for 10-15 seconds, shut off, and not turn back on. Yet there’s still fuel in the lines. Going to be installing the kit on my g80 now, so wondering if I’m missing any steps so that I don’t make my M3 smell like gas
There’s always a chance for some fuel in the line to spray out. Best is to leave the gas cap open for a bit for pressure to bleed off after running car so it shuts off without the fuel controller plugged in
@@protuningfreaks Having this same issue, i just opened the cap to see if that helps, Seemed like the gas was never gonna stop flowing so i gave up to do some research.
So with custom room the flex fuel kit adjust on the fly depend on what ethanol content is in the tank. Do we have to get an initial map flash first? Like a custom tune or we can just flash like a stage 2 and when we mix like e50 the software will automatically adjust to get that power?
On a b58 gen2 I say the highest e map is 50 is that the highest ethanol mix I should run even with the flex fuel? Or could I run full e? Also will full e make less than e50 on stock turbo?
With the multi map do I have to change the map to the ethanol content I have like say I have e30 do I change it to map 3 or can u just leave it how it is like the computer reads it so I should be good?
We actually explain it in the video but to reiterate, all map slots auto scale with ethanol present. The flex fuel sensor in the BM3 Flex Fuel kit communicates the ethanol content info to the engine computer which then in turn makes any of the map slots scale up or down in power depending on how much ethanol is in the tank. You need to run a flex fuel enabled map such as our OTS MultiMap or a custom tune with flex fuel functionality enabled.
I like the fact the sensor is at the tank sensing the content there not at the rail, by the time the sensor at the rail sense the gas it already in the motor at the tank it will take at least 30sec to get to the motor, as there’s no return line. Any idea when this will be released for the G80/82?
I have a gen 1 b58 g30 I hold down the cruise control button in first position and tack goes to 85 RPM on pump 93 gas can this also be an install issue?
I was planning on installing this with a tune, but timing might get me this kit 1st. Can I install this kit and run it with the stock tune until my Femto unlock is done?
For the G80, if we have the CustomROM is this just plug and play with muti-map or will we have to resend the ecu to femto for an update? Also when will this be coming?
Buddy installed his (mine still on the way) but sometimes when he goes to read the content of tank it only goes up to the 1000k but when it does work he get the real reading i assume it’s something he is doing lol
Hi Dzenan, I have this kit installed on my BMW f82, to which I can read the ethanol content % on the bm3 app however can’t see this on the dash tact screen when I hold down the cruise control button on the left, is this an install error ?
I have a similar issue on gen 1 b58 g30 I hold down the cruise control button in first position and tack goes to 85 RPM on pump 93 gas can this also be an install issue?
As femto unlock doesn’t allow writing of the software portion it’ll be the same as for the G80 when we released it, meaning, you’ll need to resend the dme to femto for an update to get all the new goodies.
No 91 option for stage 2+ multimap:( Any way to get 91 added so we can scale and don't need to reflash to stage 2? Me and some others are in the same boat, owning a gen 1 b58 with the PTF flex kit in california stg 2+, looks like the lowest octane level is 93 for the multimap.
@@protuningfreaks If we want it for the X3m or x4m, do we select "BMW G-SERIES S58..." option? I don't see an X3M specific product or option and the F97/8 chassis isn't mentioned anywhere.
@@peterg6953 we’ll add the specific option for x3m x4m as the pre LCI models need slightly different firmware on the controller than all others. Everything else hardware wise is the same as all other S58
![Lp. Сердце Вселенной #1 НАЧАЛО ПУТЕШЕСТВИЯ [Новый сезон] • Майнкрафт](http://i.ytimg.com/vi/380Q7gLWGvk/mqdefault.jpg)
So ready for a kit like this on my 2018 M550i. I am running the E30 stage 2 and it is amazing!!! An E85 would even be crazier.
Bro me too for my 2020 m550i . Patiently waiting 😩
Awesome content! Great Production and explanation… 👏🏼 👏🏼
Thank you 🙏
Nice job with the jumper harness
Very good Video, need more uploads, keep up the good work ! Greetings from Düsseldorf, Mo, Kingperformance !
🙌🙌
Bro what happens with the red and green wires after you unpin pin and put the red in that place
Email support@protuningfreaks.com
Did @bootmod3 add an e30 OTS map for the BMW S63tu M5/M6 in version 2.0? Great content, awesome product; I am looking forward to expanding use of BM3 for my all BMW's.
Yes sir, thank you for your kind words and support 🙏
What is the difference for the X3M? I and two other members have installed it same as the video and cannot get the sensor to read. This is extremely frustrating.
If yours is a pre-LCI model the controller may need a firmware change that simply stitches the CANBus msg id from 0xEC to 0xED lile what’s done for Gen1 G series cars. It was recently discovered that some preLCI X3M/X4M cars already use 0xEC already so it was necessary to move it over. Contact support@protuningfreaks.com and they’ll advise accordingly.
Im dealing with that right now. What do i do?
@jakrieg did you ever figure out the solution im dealing with this right now too. You would think they would have info out about this so we dont tap into random wires 😒
Bravo guys
BM3 🙌🙌🙌
I have a 2020 x3m and i cant figure out what wire i tap in to i tired con3 pin 1 and it doesnt work it actually turned my cluster off while driving. Do you know the location of the ignition wire for the 2020 x3m?
Email support@protuningfreaks.com
@@protuningfreaks you guys helped me out i think u should have the info about the different pins for the x3m on ur website.
Do u guys have an ETA for the G20 M340i kit ? Great video BTW
Just waiting on hoses to arrive, soon
Nice video! One question ...when will this be available for 1st gen G30'?
Thank you, soon
When I followed the steps for draining the fuel line on my m340, in both install and removal the fuel lines never got drained and it would spray gas everywhere. Car would run for 10-15 seconds, shut off, and not turn back on. Yet there’s still fuel in the lines.
Going to be installing the kit on my g80 now, so wondering if I’m missing any steps so that I don’t make my M3 smell like gas
There’s always a chance for some fuel in the line to spray out. Best is to leave the gas cap open for a bit for pressure to bleed off after running car so it shuts off without the fuel controller plugged in
@@protuningfreaks Having this same issue, i just opened the cap to see if that helps, Seemed like the gas was never gonna stop flowing so i gave up to do some research.
So with custom room the flex fuel kit adjust on the fly depend on what ethanol content is in the tank. Do we have to get an initial map flash first? Like a custom tune or we can just flash like a stage 2 and when we mix like e50 the software will automatically adjust to get that power?
You just need a flex enabled map like the OTS MultiMap (stage 1 or 2), or, you could get a bm3 custom map with your tuner of choice
do you press the cruise control button twice
Email support@protuningfreaks.com
On a b58 gen2 I say the highest e map is 50 is that the highest ethanol mix I should run even with the flex fuel? Or could I run full e? Also will full e make less than e50 on stock turbo?
It’ll auto scale but power on OTS will max out around where that blend lands
is there an eta as to when the g8x flexfuel kit will be out?
Very very soon
When picking a map for running flex fuel are we flashing the multimap in the fuel type choices? Or do we need a custom map
Start with ots
Any idea when the flex fuel kit for G20 m340 gen 2 b58 will be available??
Hopefully next week, waiting on lines to arrive
Can’t wait to order for my 2021 m340 ! 🙂
Kits are now available on the website :) announcement on CustomROM to follow next week
With the multi map do I have to change the map to the ethanol content I have like say I have e30 do I change it to map 3 or can u just leave it how it is like the computer reads it so I should be good?
We actually explain it in the video but to reiterate, all map slots auto scale with ethanol present. The flex fuel sensor in the BM3 Flex Fuel kit communicates the ethanol content info to the engine computer which then in turn makes any of the map slots scale up or down in power depending on how much ethanol is in the tank. You need to run a flex fuel enabled map such as our OTS MultiMap or a custom tune with flex fuel functionality enabled.
Thank you 🙏🏽
Do you guys have a definite method for securing the sensor on top of the tank, I can't seem to see a neat method of doing it
Sensor and its assembly cannot move much at all there once the top fuel hat cover is in place.
Hi. The F80 S55 have the same tune for adjusting the power label base on ethanol content. ? There is any place to see the demo ?
Of course
@@protuningfreaks any Dyno graph with different ethanol content. ?
Is the installation different for the pre-LCI x3m. Just received my new module and the wiring is different. There is no separate red wire anymore.
Its the same. Red wire can be depinned if not already done. Please contact support@protuningfreaks.com for any additional questions.
I like the fact the sensor is at the tank sensing the content there not at the rail, by the time the sensor at the rail sense the gas it already in the motor at the tank it will take at least 30sec to get to the motor, as there’s no return line. Any idea when this will be released for the G80/82?
Waiting on fuel lines, hopefully next week
is this the same for x3m comp ??
Yes
Can e85 damage your engine?
No
i need one of those license plate frames 🥹
I have a gen 1 b58 g30 I hold down the cruise control button in first position and tack goes to 85 RPM on pump 93 gas can this also be an install issue?
Email support@protuningfreaks.com
Does this work for F9X X3M and X4M?
Yes
I was planning on installing this with a tune, but timing might get me this kit 1st. Can I install this kit and run it with the stock tune until my Femto unlock is done?
Of course
When is the g80 flex fuel kit for sale? I’ve been waiting for custom rom and flex fuel kit before I ditch my jb4
Hopefully next week, waiting on lines to arrive
For the G80, if we have the CustomROM is this just plug and play with muti-map or will we have to resend the ecu to femto for an update?
Also when will this be coming?
If you already have CustomROM then plug and play
@@protuningfreaks Perfect! Thank you. Do you have a launch date as yet?
Very very soon
@@protuningfreaks thanks for launching it. Ordered mine :)
Do any BM3 tuners do custom Flexfuel tunes for upgraded turbos? Gen 1.
Of course, many, take a look at our instagram posts for some references
Buddy installed his (mine still on the way) but sometimes when he goes to read the content of tank it only goes up to the 1000k but when it does work he get the real reading i assume it’s something he is doing lol
Yeah he’s probably going into map switching by mistake lol
can we get a manual for the g80?? can’t see the configuration on which way the harness gets replaced with the red wire
Email support@protuningfreaks.com and we can provide more detailed instructions
Im on the market for a flex fuel kit to run in my 2020 g30 540i will any kits your offering work on my car?
We are releasing a kit this week for all G series, be on the lookout
@@protuningfreaks 😁😁😁😁😁
Kits are up on the website :)
Great news on order soon @bootmod3
Does the car need to be flashed with Bootmod3 prior to install?
No
Question how can u tell if u need a gen 2 or gen 1 fuel kit for g20 body’s Ik I’m slow
G20 are gen2 :)
Will the b58 gen 1 fit on 2017 540
No, its a bulkier fuel line connector, you’ll need the G series kit that’s coming up
@@protuningfreaks any idea when it’ll be out ☹️
Hopefully next week, as soon as fuel lines arrive
Do this affect anything on the emission test ?
No
When is the A90 supra kit be available. Thanks
Kits are live, we just haven’t done a public announcement yet :) it’ll go out next week with the new CustomROM announcement release
Hi Dzenan, I have this kit installed on my BMW f82, to which I can read the ethanol content % on the bm3 app however can’t see this on the dash tact screen when I hold down the cruise control button on the left, is this an install error ?
Go down to first position on cruise, not all the way down. Ignition needs to be on
I have a similar issue on gen 1 b58 g30 I hold down the cruise control button in first position and tack goes to 85 RPM on pump 93 gas can this also be an install issue?
@@chrisdell1149that can be the gas station giving you bad fuel, surprisingly common.
Hello need to know if this can also be installed in Suzuki Vitara Brezza EURO 6 Engine Petrol car?
No sir
@@protuningfreaks appreciate your response.
I currently have a 2022 m340i with femto unlock, will I be able to use the new gen 2 b58 flex fuel kit?
As femto unlock doesn’t allow writing of the software portion it’ll be the same as for the G80 when we released it, meaning, you’ll need to resend the dme to femto for an update to get all the new goodies.
@@juniorflores2366 customrom update is not ready yet so right now they’ll just be unlocking
@@juniorflores2366 we don’t do etas but should be soon
When are you going to release s58 flex fuel?
Waiting on hoses, hopefully next week
When will the Flex Fuel kit for the G20 M340i be released?
We’re just waiting on hoses, hopefully next week
@@protuningfreaks Will the new kit also fit the A90 Supra?
If you check the video, you’ll see we have the supra/z4 kit coming as well
They sent me this kit for my s55 f82 will it work????
Its not a mistake. Its the same kit as the GEN1 F-series B58 kit as of recently. You can always email support@protuningfreaks.com for confirmation.
No 91 option for stage 2+ multimap:( Any way to get 91 added so we can scale and don't need to reflash to stage 2? Me and some others are in the same boat, owning a gen 1 b58 with the PTF flex kit in california stg 2+, looks like the lowest octane level is 93 for the multimap.
Also, I gotta grab one of those license plate covers eventually!!
We can easily add a 91 slot, email us at support@protuningfreaks.com for assistance.
New plate covers will be on our website this week 🙏
Does this apply to the 2020 X3/4M? I’ve been told there’s no room under the fuel hat and we have to go there under hood route.
Yes, we have kits that fit both locations
@@protuningfreaks If we want it for the X3m or x4m, do we select "BMW G-SERIES S58..." option? I don't see an X3M specific product or option and the F97/8 chassis isn't mentioned anywhere.
@@peterg6953 we’ll add the specific option for x3m x4m as the pre LCI models need slightly different firmware on the controller than all others. Everything else hardware wise is the same as all other S58
@@protuningfreaksso this the issue I’m having! I have an open support ticket. I have a pre LCI X3M and my car won’t read? How do I fix this.
@@JAKriegdid you ever figure it out im having the same issue
Will there be a flex fuel stage 2 ots map for g20 m340i ?
Yes
On some of the sites it says we can order for the g80 is this true?
Yes, G80 kit is available, same kit for all S58
Does the flex fuel kit for the g80 fit on the x4m?
Yes
Will the g80 flex fuel kit fit the f97 x3m?
yes
Do you have one for b48 ?
Yes same as b58
What about the n55
Already out for a long while for N55
Anything coming for the 2020 n63 m550 ?
Tuning is already available
@@protuningfreaks any flex fuel hardware?
We do but the flex fuel functionality that’s in our CustomROM isn’t available yet for your vehicle
@@protuningfreaks is there a likelihood it will ever get developed? I don’t want to get my hopes up
Do I need a motiv reflex for custom flex fuel tune or all I need is the BM3 flex fuel kit
Just flex fuel kit
Bit new to this. Besides a tune do I need to be running any other mods to support this?
Nothing else