DIY Automatic Water Pump Controller at home II Low cost II
Вставка
- Опубліковано 14 жов 2024
- Hi friends today I am going to show Automatic Water level Controller for your water tank at home .
It is very easy to make and low costing You can control up to 1hp motor by it.
Thank you for watching .
Very amazing bro i try this.. 100% worked.. 💯🔥👌🏻
A greeting from Mexico. Thank you for your contribution to knowledge. It would be good to make a video where you indicate the control of the tank. This is to prevent the bomb from burning. In other words, to protect the pump in the absence of water. (empty tank). Thank you very much.
When the tank runs out of water, the pump will not activate by asking for water (pump protection).
Excelente ideia. Otima sujestão.
Great point! Greetings from India. We do have level controllers that detect dry run of the pump; that is, after several seconds of start up of pump, if there is no water flow at the outlet, there would be an alarm and the motor is turned off. We then have to manually inspect and resolve the issue.
We could add more sensing too - motor temperature, abnormally long run (due to water being continually emptied) etc.!
Useful project in a simple way.
Interesting circuit system. Can please do one that pumps water out when the tank is full please
I made the exact circuit works very accurate thanks for the circuit
Can u tell where to fix led for low medium and full connection
220 v comea as output so how you used small water pump? Please replay its for a project
Thank you very much for uploading this circuit! I have tried your circuit, unfortunately when the tank is full, circuit doesn't cut off the power, hence the relay being on! All the parts were checked and they are found ok.
Please give me way how to overcome this problem. Thank you.
It’s working very fine I liked but can you do other way around motor stays off and when reaches high it turns on and off when reaches low point please 🙏
I've made this with 230v ac pump but can this circuit work on 12v dc pump
you can use 12v relay and control any 220 device
Good work, please tell 5v supply circuit ,cable maximum length ,can add water level indicator to this circuit.
How to eliminate problem of electrolytic corrosion of sensor wires
It will give in bread board to connect pls reply sir
Can this system work on 5 volts?
can i use 12 volt 1 amp adapter?
Super. Simple and best. Where can we get the kit?
Will it work for 1HP motor? What are size of the apparatus?
Can I use 9v battery instead of 220v, for a 12vpump?
yes you can
I bought bc548 instead of 547 and dont have enough time to change it. Can you suggest any alternatives to make it work?
You can use bc548 as well both will work same
Will it work With 1000 litre Tank and A Submersible Motor ?
hello is it possible to do the opposite of this circuit?
So when the tank's full, the engine's going to work, and it's empty.
Ofcourse .... Connect the motor to the normally closed pin of the relay. Thus when the tank is full the pump will start working... When the water level drops below the threshold level it stops
Good one! I can use this on my water tank.
Just use opamp
Can i use this for auto Off Only ....
i do not want this to turn ON automatically
Good one but if i use long wire around 15 m it's not working.
Can u help me out?
I would like the pump to turn off in the LOW position and turn on in the HIGH position. Is it enough to swap the relay contacts?
Haii hello ican help you? How built in 24volt adaptor usage to automatical waterlevel control
I made the circuit. But when the motor starts the base register of bc547 and 555 ic gets very hot. What to do ?????
Is it shock proof , shock neni lagega ya lagega
agar auto start na lagaye only Off lagaye to chalegaa?
Sir can you tell me which motor yiu have used?
Good Very good
Bhai iss project me banane ke liye iska equipments kha pe milega or motor kon sa hai
Very usefull for practical life... 😮
Can u plz say how much does it cost?
Mas o projeto é show de bola!
project to accha he lekin isme ak dikkat he..ye to only uppar ki tank ka project he agar iske sath under ground tank ka system hota to or bhi accha ho jata..or isme agar full tank hone par buzzer add hota ho to vo bhi kar dena....
try to upgrade your system with second under ground tank ...
Using relays with bigger amperes , this design can be used for bigger or heavy duty AC water pumps. .
What relays will I need for an AC Submersible Pump?
U can use magnetic contactor for run submersible motor
What is the adapter rating is 500milli amps or 1 amps
Because i tried this with 500 milli amps it works but in 1 a it wont work
How can I make this for one way with a sensor or a switch?
Maybe you can help me with what I'm looking for. I'm buying a 129v electric water dispenser. However it doesn't come with and automatic shut off valve. I am hoping to find something automatic that has an automatic switch or sensor that will allow the water to pump and stop. Kind of like how alarm system sensors or a type of toggle that when something is moved or a door is opened it activates.
I hope I'm clear...
Would you happen to know what I could buy that would do that that I could connect to the water dispenser and have it automatically activate and deactivate?
I'm open to suggestions. Also must be a very small application that I can mount to a wall or pole or rod... Thank you and anyone who can help.
Please draw the DC connection on relay
Whats that yellow and red wires are for? Kindly answer.....
Great video!
Sir pura circuit bataiye na kis kis jagah connection Kiye Hai
Is there current flowing in bucket ???
Nice, #ENGINEERBACCHA
Hello, I tried but it didn't work. I used exactly the same components except that the water pump on my side is 220v
Can use any IC other than 555IC
Sir i have open well in my farm field that well will fill once in a 2/3 day's and it is far away from home and i want to wait for power supply (supply provided by electricity board in shift wise)it's difficult to go and come plz kindly give modified circuit for operating irrigation pump when well is full and off when well getting empty .sir i am waiting for you replay kindly help to this former.
Srikantha M.B , I've a solution for you problem...!
whatsapp me @ 9989800949
I can use the battery of 12 volt please give me the diagram of the circuit minus plus
Hola disculpa esa corriente que pasa por el agua afecta al cuerpo humano ? en caso que se conecte a un tanque de agua para baño ?
Fantastic idea
Bro kia ye revers me kam krega mtlab k me chahta balti se pani full hote e pump use khali krde?
Yes..
Motor ka power supply NC( normaly close) pe connection kar dije relly pe..
What is voltage rating of the water pump?? that you are using
this can be upgraded for a small house pump?
Yes, you can.
you can use it up to 1 hp motor
What is the specification of dc adapter you use
Power Supply kitna volt diye ho?
But this circuit is not use in water motor , because the relay that you used in circuit is 7-15A.......
U can use magnetic contactor for run 1.5H motor
can some give the name which equipment used in this??
Can i use motor listrik i didn't see it thas why i still confuse
full of details this model like cost, components, minimum & maximum price etc.
Sir the ic used in this circuit is
NE555 or any other ic sir and the relay is 12v how many amps we use sir ?? Please reply
I am using circuit is good for upper tank now it is requested to give circuit for lower tank such as upper tank working is good i used bigger relay instead of small working is good
Sir mera Tanki Motor se 12-13 meter dur hai, motor automatic off hone ke 20 minute bad firse automatic on ho raha hai. Aisa continue hota ja raha hai. Please help me!
Is work for top water tank
Tank on 3rd floor is it work
You just demonstrated your skills without showing exactly how did you wire the 555 timer. The diagram doesn't show how the pins are connected and the numbering you used are misleading. Correct me if I'm wrong.
Two level switches and a relay will do the pump automation.
what is that sensor wire. please send the name of that wire and photo
Bro work aagala bro 12 volt supply poga kooda mattukkudhu
Sorry,tell me the name of that black devices.
Sir rely contion
hai sir, 1m resistance kithina wats 1k resistance kithina wats pls bathaya...
Sir I am doing project
My project name is water level controller by using pic micro controller
In our project we use two pics sir
First pic is 16F54
Second pic is 12C508
The first pic is giving connection between sump tank and water tank.(overhead tank)
The second pic is only used in overhead tank
I want circuit diagram for both pics and also I want code .
Bhi ham esh mein Kitna w or Kitna ampere ka supply de
Wonderful!
My circuit is not switching off....its continuously in on state...pls help
I want to run 220v motor through it how can i do that?
Contact us email neoteccwlc@gmail.com
@@neotecwaterlevelcontroller4031 ,vc não tem o desenho mais detalhado?
Excelente.Favor el plano del Circuito
How can I use this for 1HP motor ?
Sir , can I use diode in4004 instead of in4007 please relay me fast
sure u may
May i use 5 volt realy
upar ki tanki me bich ka wire he voh pani me rhetahe jab pani voh wire se niche jatahe tab moter start hotihe jab pani bich vala wire ko tuch hotahe to moter off hojani chaiye parantu kyu nahi hotti????.
Relay la connection change kar do..
Sr i can't get the resistor 1m so how can i change that resistor pliss🙏
Sensor ke kaki no 6 IC tdk bekerja,apa yg salah?
Bro I did this but relay bar bar fuse ho raha he heat hoke melt ho raha he kya kare😢
ज़ब वायर 3 लगाते है तो दूसरी मंजिल पर वायर रेसिस्टर बदल देता है तो सर्किट फेल होता है
मैंने स्टील वायर भी लगाया सिल्वर वायर भी लगाया ये 7 मीटर बाद सर्किट फैल हो जाता है 5 मीटर तक वायर मै काम करता है
جميل جدا
But good
2hp moter also same circuit working
Can i use other transistor besides bc 547
Yes use any npn transistor
Ok ty mr
Dear sir please that how to 1 hp sumrsible pump with stater conection
Hey! Sorry tell me the name of that black devices.
The name of having 8 pons is --IC 555
Sir mene yes project work tyar karna hai
I can use battery of 12 volt
Is that working?
I am waiting for your reply sir 🙏
Please tell how much voltage the motor you use.
220v
@@creativeetc Please draw the DC connection on relay
doesn't work,, the high level wire is of no use.. basically mid and low wire are the main wire,, there is no need of timer ic ..stop making people fool!!
Yes bro i tried 😢 and waste 130 rs but not worked
Respected sir
I am from mohali I watched your vdo I tested your project with glass of water and it is correct
my half HP motor work good but with water tank it not work what's recommendations for it I hope you will give me answer
When 12v supply going to tank than it is drop because water pipe is grounded so use flot switch other wise your time & money waste .i also used but these circuit are failure at 20, 30 feet.
Naked of two wire +12 v and pin 2 should be closer.. In tank
You can all +12 wire( in water of tank) should be naked.. And use very small wire for pulse..
It worked but my ic is burning always
Mas klo saya pesan, kirim ke.SMG harga brapa. Urgen dispenser galon bawah saya rusak.
Sir mujhe es project ki pdf file chahiye thi plz aap avelable krwa do
Muzhe bhi chaiye
High level pe band ho jata hai fir high level jane bad chalu ho jata hai