Built the same with just Rs.2500 including all the parts mine was laser cut, rods were salvaged from old printers and the steppers were also from old xerox machines... The acrylic used was 16mm, 10mm & 6mm.. 120kg for acrylic scrap, parts took around 14mins to cut on co2 laser CNC 14mins x Rs. 8 = Rs.112, steppers cost Rs.60 each minebea 1.7amp 1.8deg, cnc shield +arduino uno+pololu stepsticks driver=Rs.1200, linear bearing Rs.600...
Hey ! Any chance I could get access to your laser cut files ? I wanted to print them first, but I guess printing them with an old ultimaker could be difficult. I would really appreciate your help !(: Thank you!
How to wire the pen holder motor, because it has five connectors while the cnc shield has only four connectors for each stepper ? Thank you for this great project.
My cnc pen plotter is going on the wrong side. When it draws the picture, it is not in this direction, but it is moving to the left side. how to fix it? Is it a software problem?
My machine not work. in test servo motor its work only one time down or up. i am run file in ugs stepper motor work only 1 sec. and machine stuck. give any suggestions.
Could someone please explain how do the belts go around the pulleys? I just don't understand because it's all happening inside and it's keeping me awake at night.
I just responded to one of the other many comments asking about the belts and see you asked just 6 days ago so I wanted to make sure you saw it so I'm posting it again. ua-cam.com/video/_nzxGOKhHSY/v-deo.html
Hello Konstantin Konstantinov, I have already built the cnc plotter but I can not control the pen rise and fall. I do not know if it has to do with the gcode file created in inkscape. When I am printing the pen is always in the same position, it does not go up or down. Can you help me?
If I want to increase my plotting area, what should I do? Will increasing the shaft size only do the job or shall I need to modify the electronics and code also?
What is the length of the threaded shaft and what is the measurement that it can draw (ie, Draw a maximum larger border line measurement L X W) Please reply..,...
Hi Konstantin, Great job, I like it. I already build similar drawning machine, but have a problem with calibration xy axis. Can you tell me please, how to set the working surface of the machine (via inkscape or by arduino?) Thanks in advance.
i find amaizing what u did !!! And i want to make also one like u did, at the moment i study electronics and i think it will help me a lot. a detailed instruction i found also at the website adress that you provide in the description but i need to know if : do i need a 3d printer ?? do i need linux ?
Подскажите пожалуйста куда подключить серву и нужен ли драйвер Zоси на шилде (при использовании сервы)? Собрал как в видео, все заработало. Есть необходимость на Z поменять мотор на серву. Пробовал grbl файл для сервы - машинка не работает совсем.
Hi, Konstantin Konstantinos, congratulations for the video. It's very useful. Can you send me the link to the 3D part that supports the arduino. That it does not exist in the site where they are, another. Thank you
Greetings from dubai! I plan on making this same arm. Can you explain in detail how you connected the belt? Also can I use this same mechanism with longer rods to cover 40x40 cm paper?
good day ! tell me how to tune the servo motor in arduino by 90 degrees of deflection and then return to the zero point! I need to attach a marker! Thank you
Hello Konstantin Konstantinov, I have already built the cnc plotter but I can not control the pen rise and fall. I do not know if it has to do with the gcode file created in inkscape (mac), or if it has to do with the program I use to print (cncjs - mac). When I am printing the pen is always in the same position, it does not go up or down and gives the error id = 23. Can you help me?
Hello again Konstantin Konstantinov, I do not use any command in gcode to control the Z axis. I simply load the gcode file that was generated in inkscape and say to print. What is the correct way to do, and how to command the Z Axis?
Hello, good job on builing it, looks great, thinking about making a similar one. What plastic did you use for parts? How much money did you pay for printing more or less? Peace!
thanks a lot sir for a complete guide about grbl modification. you are only one who tell this. thanks again
I'm totally digging the music
Built the same with just Rs.2500 including all the parts mine was laser cut, rods were salvaged from old printers and the steppers were also from old xerox machines... The acrylic used was 16mm, 10mm & 6mm.. 120kg for acrylic scrap, parts took around 14mins to cut on co2 laser CNC 14mins x Rs. 8 = Rs.112, steppers cost Rs.60 each minebea 1.7amp 1.8deg, cnc shield +arduino uno+pololu stepsticks driver=Rs.1200, linear bearing Rs.600...
make a tutorial
Khadim Ali where and how I can get it?
Please, could you provide the dxf files? Unfortunatelly, I don't have 3d printer, just a small cnc router.
AA . Khadam Ali bhai . I want to see this machine . Can I contact you or can I buy from any place . Plz ? SMS me 03227663131
Hey ! Any chance I could get access to your laser cut files ? I wanted to print them first, but I guess printing them with an old ultimaker could be difficult. I would really appreciate your help !(: Thank you!
MATHIMATICS I ACTION , THANKYOU FOR SHARING THIS HOME MADE DRAWING MACHINE
background music.
first I feel like it coming from outside of my house .
.............. turn it off ....listen to your own music ... why the bitching ....
What the fuck do you have with those who didn't like this shit music?
Sir ,Kindly make vedio on software installation n implementation .
Wow, nothing like checking your final edit before uploading huh
Good job , can you sent new link for your files.
I was so impressed with your build. That I also build 1 like this. But theFiles and software link is broken. If you could share the files please
How to wire the pen holder motor, because it has five connectors while the cnc shield has only four connectors for each stepper ?
Thank you for this great project.
Pen is controlled by a servo i guess
Very nice Drawing Machine, I am building one for me. Thank you for sharing.
which software would you use
I've been trying for 6 months now but the servant doesn't
I don't know what else to do!!
Nice video. Wanted to see how the movement work, it looks like CoreXY.
My cnc pen plotter is going on the wrong side. When it draws the picture, it is not in this direction, but it is moving to the left side. how to fix it? Is it a software problem?
Where I can buy it.
My machine not work. in test servo motor its work only one time down or up. i am run file in ugs stepper motor work only 1 sec. and machine stuck. give any suggestions.
I followed all ur steps..in gcode sender.. i upload a gcode file.. it doesnt working..
I like those Indian drums in the background. I use that those sounds meditate. I like the video. ThanQ
can you send me link of software and program link
I have just built one like this but the controls are 45 degrees off as the clock turns. Is there something GRBL or $$ that can be changed to fix this?
Where must i the belt together ???
I make this machine but wen i rotate one motor the machine move in 2 direction
New link for writing kit please
I want to know how belt was connected
Please explain
Could someone please explain how do the belts go around the pulleys? I just don't understand because it's all happening inside and it's keeping me awake at night.
I just responded to one of the other many comments asking about the belts and see you asked just 6 days ago so I wanted to make sure you saw it so I'm posting it again. ua-cam.com/video/_nzxGOKhHSY/v-deo.html
Files and software link doesn't lead to me download link will you please send me the link or directly to me !!
which inkscape plugin is being used to create the Gcode?
Hello Konstantin Konstantinov, I have already built the cnc plotter but I can not control the pen rise and fall.
I do not know if it has to do with the gcode file created in inkscape. When I am printing the pen is always in the same position, it does not go up or down. Can you help me?
wow that song made me mute this video quite fast
............... really ...... is that what you got from this video ...... as if the rest of us would be lost if you didn't post that ......
Lol the song is so soft anyways!
Hi, can you put a drawing file for example square or rectangle, because i have probably connected the wrong motors.
If I want to increase my plotting area, what should I do? Will increasing the shaft size only do the job or shall I need to modify the electronics and code also?
классный станок, классный видос, классная музыка)
Теперь осталось сделать так, чтобы в штатив можно было и фрезер поставить, и выжигатель...
Hi there. I got little problem when i make a print it printing 45 degree angle why it’s happen?
I would like to buy only the plastic parts, how can I do?
How do I change the surface of drawing area ? I want to build a drawing machine with an area of 100cm x 100cm .
Can you just say what type of screws you are using. Type and dimensions please.
how to wiring motor to cnc shield board, please master ?!
Good project. Could you list the bolts, nuts and screws, etc.? Thank you.
Too awesome work dear...
Can we use same mechanism for 2axis hotwire CNC machine?
What is the length of the threaded shaft and what is the measurement that it can draw (ie, Draw a maximum larger border line measurement L X W) Please reply..,...
If I increase the length of each X axis and Y axis to 100mm, do I need to change the code and modify the software?
And where do they change?
hello sir when i move x+ it moves diagonally can you help me to solve the issues
how did you connect the 28byj to the shield? the 28byj have 5 wires i you need 4 for the shield.
Hi, I want to know how I could get the whole package to put together and how much would it cost? Thank you .
Hi Konstantin,
Great job, I like it.
I already build similar drawning machine, but have a problem with calibration xy axis.
Can you tell me please, how to set the working surface of the machine (via inkscape or by arduino?)
Thanks in advance.
Same problem with me...did you fix it?
can you provide 3d printing file? thank you very much🙏
i find amaizing what u did !!! And i want to make also one like u did, at the moment i study electronics and i think it will help me a lot. a detailed instruction i found also at the website adress that you provide in the description but i need to know if :
do i need a 3d printer ??
do i need linux ?
Where the hell I can buy those 3d printed center plastic
What is measured by the size of drawings of 3D objects?
Hi, how do i modified the code so that it recognizes M3 and M5 commands?
Hello, may I ask does this work with colour paintings? Thank you.
Can someone help me?. Why have some change the code in 16:33 ??
What is the function when you change this ?
Nice to see a project running in a linux machine with kde.
Can you please share the software and firmware link. Link is dead
Very nice video ji
sir can you plz tell me that how did you mount that gt2 pulley..?
This machine worked based on inkscape Android application or not..??
Very very very gooooooood !
really creative
Подскажите пожалуйста куда подключить серву и нужен ли драйвер Zоси на шилде (при использовании сервы)? Собрал как в видео, все заработало. Есть необходимость на Z поменять мотор на серву. Пробовал grbl файл для сервы - машинка не работает совсем.
There are no endstops for homing?
How did u assemble belt
Hello, the page with the software information does not work, what is the name of the software you use?
Please anyone can help me ? I want to build same one, but bigger, were can I buy the staff please help me
i still dont get how you get 2 axis motion with both stepper on the x axis...:( didnt show the cable routing.
I've been designing my own and use the same belt system. I found this video which explains the motion: ua-cam.com/video/_nzxGOKhHSY/v-deo.html
@@RJFeddeler thank you for the link and saving my day pal.
Осталось собрать 3д принтер, есть видео?)
Hi, Konstantin Konstantinos, congratulations for the video. It's very useful.
Can you send me the link to the 3D part that supports the arduino. That it does not exist in the site where they are, another. Thank you
thank you Konstantin Konstantinos
Did not understand the GT2 pullout scheme of the belt (
How do you route the belts ?
Can i use longer screw shafts
For bigger drawings?
I tried to download the gcodecreate.zip but it said that it is a virus.
Can I get a safe download somewhere?
can i help you peeka? i installed it. and using it. not virus.
HELLO ... GRBL MASTER FOLDER ARDUINO LIBRARY NOT ADDED. NO LIBRARY. YOU HAVE SHARED AGAIN. THANKS
how to insert belt plzz explain properly
Greetings from dubai!
I plan on making this same arm. Can you explain in detail how you connected the belt? Also can I use this same mechanism with longer rods to cover 40x40 cm paper?
Ohh okay got it. Just to clarify you are using just one single belt that runs through the arm right?
Also what is the reach of the arm in the video?
how to make plastic stage ,end 1, end2 ,pen holder and its procedure
thank you for the stuff.
what is the firmware you used to control the Z axis with the 28BYJ-48 12V Stepper Motor please?
Can you tell me the scale size of all components please
Можете помочь сделать такую штуку для написания конспектов, пожалуйста?
What happened to good ol' elbow grease?...
where is the arduino programming?
put it somewhere else!
How can I connect to servo? which pin should I use?
the account was suspended. please send me a message with the complete material.
Thank you
Can it used be for writing?
do you think it is worth using this project for a 3d printer?
Can u make a belt setup video
Can it be used for writing?
good day ! tell me how to tune the servo motor in arduino by 90 degrees of deflection and then return to the zero point! I need to attach a marker! Thank you
You need to tune it in gcode.
Watch this. At last there are two options. Mess with the values.ua-cam.com/video/H5_i8ruAXno/v-deo.html
Why can't the STL files be opened
Where's the audio?
How much it's price... I want to take....
plz post eletronic installation
Hola, amigo como puedo adquirir ese producto. Por favor ayudame.
what can I say magic the music and video well done and thanks
Hello Konstantin Konstantinov, I have already built the cnc plotter but I can not control the pen rise and fall.
I do not know if it has to do with the gcode file created in inkscape (mac), or if it has to do with the program I use to print (cncjs - mac).
When I am printing the pen is always in the same position, it does not go up or down and gives the error id = 23.
Can you help me?
Hello again Konstantin Konstantinov, I do not use any command in gcode to control the Z axis. I simply load the gcode file that was generated in inkscape and say to print.
What is the correct way to do, and how to command the Z Axis?
ty
Mind blowing ideas....
What is the torque of this stepper motor
Hello, good job on builing it, looks great, thinking about making a similar one. What plastic did you use for parts? How much money did you pay for printing more or less? Peace!
What kind of 3d printer is this??
I would like to buy one but I have no idea what should I choose...
the malyan m150 doesn't look very promising to me... Witch one do you use?
I am looking right now at a Tevo Tarantula what do you think of it?
How much does college cost at present in your country?
Can you share if there is a grbl download link?
can I get the STL files of these 3d prints