Parkside PTK 2000 E3 table saw run test
Вставка
- Опубліковано 27 сер 2024
- Parkside PTK 2000 E3 table saw available on lidl shops.
Technical details:
Power - 2000w
Speed - 4800rpm
Cutting angle 0-45 degrees
maximum cutting height - 87mm
Saw blade - 254mm
Please check out my other social media profiles for more videos, photos and insights:
~Shop: danielh.ro
~ Facebook: / danielhatelier
~ Instagram: / danielhatelier
~ Twitter: / danielhatelier
~ Collaboration mail: danielhavrince@gmail.com
#parkside #tablesaw #workshop
![Lp. Сердце Вселенной #1 НАЧАЛО ПУТЕШЕСТВИЯ [Новый сезон] • Майнкрафт](http://i.ytimg.com/vi/380Q7gLWGvk/mqdefault.jpg)
Zaaggeleider en inlegplaat zijn waardeloos!! Anders top machine 😅 heb deze ondertussen 2 jaar (regelmatig gebruik 3a4 x / week )nog zeer goed werkend)
You do have to spend some time setting the saw up... blade, fence, etc. But once done, the saw is great. Fairly compact which is Nice ua-cam.com/users/postUgkxXh-4_3-ZT1fFWP91ZV7iVqzElr0lEb-a I did get an Incra Miter Gauge which takes some setup as well. The stock miter gauge can be adjusted in the miter slot with a little painter's tape... this tightens up the side to side play a lot.
Some stupid comments about its quality what else can you buy for £99 and have a 3 yr guarantee..... muppets
The problem is that these cheap garbage tools exist in the first place. Not more than just electronic waste. Better to build a table saw from scratch from plywood and second hand motors than buying these cheap chinese toys. Sure it might cost you twice the amount, but I would rather spend around 200 and have a tool that I can rely on, than make poor cuts because it gets out of alignment each time the material passes through.
Many say that the Parkside firm is bullshit, but like any firm it has its pros and cons. I have several tools from this company and they completely suit me.
Some of their tools are alright, they have some failures too
Parkside 8s just a generic brand. The companies that make these tools differ.. though most of these companies are in Germany..as far as i could read. They are made for LIDL and lidl sells them under the Parkside brand.
I have loads of parkside tools some great some just average but I managed to burn the motor out in this table saw in less than 10 hours of run time spread over a year. I would say its ok for the DIY fan but only use it on soft woods. Stripped it for parts as had lost the receipt and couldn't take it back.
Agree with you
if you don't plan on losing your fingers lower the fricking blade. The blade should be kept like a few mm above the workpiece.
Scule noi în atelier!
Să le folosești sănătos și cu mult spor.
Like 👍 evident 😉
Stai sa vezi ce urmează sa apara
@@DanielH
Voi vedea 😉👀😎
Îmi intră notificările 😃
This video will be a nice reminder of when he had all his fingers.
I agree, i pushed the limits a little bit. Sorry 😐
I have the older 1 of these. Job 1 throw away the supplied fence and make your own 1.
hi , i can cut plexiglass with it? thank you
Yes, but you need a good saw blade. And i already made some plexic cuts. Also you need vacuum to clear the dust
Parkside or einhell table saw u reckon?
I'm on a job myself in glasgow making tv sets up .and will need to rip timber, ply and mdf from time to time
doesn't matter, both are built the same way. I had the Einhell, basically the only usable part is the motor itself. The fence is.. well non existent imo, the table is cheap and uneven, the mechanism for setting the angle is a joke. If you want to cut something to a rough approximate, it's ok I guess, but otherwise, both are garbage.
I think the safety guard for the blade came with the saw for a reason!!!
" it can't happen to me",
That blade change looked well fidderly
Big like!👍👍👍👍👍✅💪Felicitări! Great video 👍
Mulțumesc
Buna ziua daca nu va suparati e de vinzare ? Si cit costa si de unde sinteti ?
Nu am de vânzare. Doar am prezentat unealta.
Încercați pe grupul Parkside Romania pe Facebook, poate are acolo cineva.
yesterday I received a PTKS 2000 G5.
but it's so bad that even the table isn't flat; in addition, the movement of the saw is irregular when it goes up and down. I'm going to return it
Yep. it's bad. But I used it till I will have money for a professional table saw
Would anyone recommend this table saw
If you have budget I can recommend to go near DeWalt or Bosch table saw. The Parkside is good but I feel the safety is a big issue, the motor is held only in 1 point, wobble a lot when cutting. Maybe mine was faulty, I don't know
Do you recommend parkside E3 or G5 model ?
For quality work DeWalt
Sa fie într-un ceas bun :). Am o idee de produs, pe care nu prea îl găsesc pe piață, cel puțin nu cum mi-l imaginez eu.
Da un mesaj privat
Can’t see the point of making a review video if you don’t speak! Waste of time....
The cat ate my tongue
Well, aren't you just delightful. I don't see where he claims it's a proper review. "Run test" is the title. Cheer up, mate.
Quali sono le differenze dei modelli che esponete
Sa-l folosesti cu mult spor!
Mulțumesc
Super! De unde achiziționezi placaj stratificat?
Holver
What do UA-camrs have against guards?
I don't know
Ce nota i-ai da?
Nu stiu, un 6 din 10?
Do parkside sell fingers
Of course. They are bonus with every product
having so much of the blade protruding when doing a shallow cut is dangerous and reduces the lifetime of the motor and the blade.
Thanks for your help
la asta chiar puteau sa ii faca pana la inaltimea panzei, la al meu vine altfel aparatoarea, eu i-am taiat pana sa nu mai trebuiasca sa o dau jos cand fac canale. oricum al meu a avut viata grea, i-am schimbat doua randuri de carbuni si rulmentii de pe rotor.. nu cred ca ma mai tine mult
Eu nu am reușit nicicum să pun laserul.
Esti multumit de el?
Nu am lucrat cu el mare lucru. Mi-a fost frică că era prea instabil motorul și se ținea doar într-un șurub. Am trecut la DeWalt între timp. Cel Parkside l-am abandonat.
Salut. Doresc să achiziționez modelul acesta de circular și aș dori să-ți cer părerea personală văzând că ești un posesor și nu oricare, ci unul care se pricepe. Cum stă la capitolul precizie, tăieri drepte și la diferite unghiuri?
Tot ansamblul cu motor si panza e cam subțirel prins de cadru si daca impingi mai tare in el, afectezi calitatea tăierii. La fel și la taierea in unghi, dacă abuzezi, va tăia aiurea. E foarte zgomotos si unpic instabil avand in vedere ca picioarele de sustinere sunt de tabla subțire si "carcasa" de plastic. Pentru hobby si tăieri din an in paste cum fac eu pentru proiecte pe UA-cam e ok, pentru producție sau pentru precizie, nu il recomand. Costa totusi 600lei.
@@DanielH fiind încadrat/fixat într-o masă ca cea făcută de tine, se remediază "deficiențele" astea?
Nu neapărat. Masa am făcut-o pentru a avea mai mult spatiu de lucru in atelier. Inca nu am testat dar 90% nu schimba cu nimic performanță circularului
@@DanielH Mulțumesc pentru informații! Spor la treabă, ești demn de urmărit!
Mulțumesc.
Es exactamente igual que la mia, pero la mia es verde y marca einhell
maybe who knows where to get it new electric motor for this table saw ?
I honestly don't know 😭
What was the replacement blade, and did the saw come with both?
The saw comes with 2 parkside blades. 25 and 40teeth if I remember correctly. I think I use the wolfcraft blade at the moment. Much better quality
Super le prix?
This mission is available
Ma interesează un abric, cu grosime, și un circular,
Și eu caut abrict.
Qual o preço obrigada
My one burnt out after 2 days, they replaced it no problems and then it chopped my finger off, I don't like woodwork.
Sorry to hear that. Workshop safety is important.
" It " didn't chop your finger off - You did! What kind of person blames a tool for them being a twat?
@@Nitecrow314 🤣😂🤣😂…my thoughts exactly…🤣😂🤣😂
Unde se gaseste placaj din asta asa gros?
La depozitele unde se vinde pal și feronerie pt mobilă.
In baia mare îți zic exact unde. Prin țară nu știu. Mathaus nu au in stoc de ceva vreme, dedeman și brico doar de 4mm.
In Bucuresti vroiam, ca prin magazine gen dedeman, leroy, hornbach am vazut doar din ala de 4 mm. Din-asta gros vad doar pe youtube la astia prin SUA, de credeam ca nici nu se gaseste pe la noi 😁
Holver probabil
Comanzi un camion direct din Belarus.
Poti crăpa posta cu el ???
Da, am tăiat poștă cu el. Doar că am folosit panza cu multi dinți, nu e recomandat
Same as my evolution table saw shit quality needs hours of tweaking to make it any where near accurate chuck the fence and make one and chuck the table as well in fact chuck it all cut your losses and get a Dewalt or the like cheap tools are yacky just cause grief
Cit Costa
It make a lot of noise!
Everything on it is fragile.
I made my own fence.
It's cheap
@@DanielH I'm cutting bamboo poles with it right now.
I hope the motor will hold it until I'm finished🙈😔😀
Spor la treabă.
Mulțumesc
Cit Costa pretul
Nu o vând eu. Apare ocazional in oferta Lidl. Undeva la 600lei este.
Am cumparat ceva scule Parksaid sint multumit calitate pret lucrind intensiv egaleaza sculele mele hitachi plus de asta cu pretul unei scule hitachi cumperi 3 scule parksaid
Aveți dreptate
Viz
If the table saw is anything like the rest of parkside range then I wouldn’t touch it would a barge pole!
When you power it on, sounds like an airplane ready to take off. When you push the material in, all that anger flies away and almost dies
like 8
Blade guard.. Looks too lethal. Mate lost finger working at work..
De