The wires connected to the magneto generally serve the following purposes: Ignition Coil Wire: One of the wires is connected to the ignition coil. The ignition coil is responsible for transforming the high voltage generated by the magneto into an even higher voltage required to create a spark at the spark plug. This spark is essential for igniting the fuel-air mixture in the engine's combustion chamber. Charging System Wires: The magneto also generates electrical power to charge the scooter's battery and supply power to various electrical components, such as lights, horn, and accessories. There may be wires connected to the magneto for charging purposes, typically consisting of a regulator/rectifier unit and other wiring related to the charging system. Stator Pick-Up Coil Wires: The GY6 engine might also have a stator pick-up coil, which plays a role in determining the engine's timing and is used for generating signals to the CDI (Capacitor Discharge Ignition) unit. The CDI unit controls the ignition timing based on input from the pick-up coil. Ground Wire: A ground wire might also be connected to the magneto, which helps dissipate any residual charge and ensures safety during maintenance. Thank you for watching my video
Please help...my flywheel tool does not screw in turning left it wants to screw in right but once I screw it in and tighten the back piece it was to strip off
Hello my friend try to tilt the scooter little bit on the left side spray a little of penetrating lube around the center shaft and let the scooter seat for one hour there is a possibility that the woodruff key inside the shaft is making resistance one time I had to cut my flywheel in small pieces and that is a lot of work. Thank you for watching my video
I want to say thank you for your videos I've been riding a scooter for going on the 15 years now he'll probably longer honestly I can't remember lol but your videos have helped me out so much and I really really appreciate it friend Thank you
You're welcome! I'm really glad to hear that my videos have been helpful to you over the years. It's amazing that you've been riding a scooter for almost 15 years, and your dedication to it is truly admirable. Whether it's been a long time or not, what matters is that you've found value in the content I create, and I appreciate your kind words and support. Remember, the joy of riding a scooter comes from the passion and love you have for it. Keep enjoying the ride and exploring new adventures. If you ever have any questions or need further assistance, don't hesitate to reach out. Thank you for being a friend and a part of this wonderful community! Happy scooting!
Hello my friend sometimes when the coil gets old could be flickering or could be the pick up coil next to the magneto / Flywheel. Thank you for watching my video
Thank you!! You have helped me a few times. I want to ad that we appreciate you!! You explain everything so very good!! I will always come to your channel for any help with our scooter! Bless you and have a great day!!
Hey buddy.. have a question.. what is the tread size or Inner diameter of the tool I need to buy for a YB50QT-3 - 3 4 stroke 50 CC we went to the Yamaha dealer and he gave us one to big in size.. 2015/04
Hello from Perth western Australia! Thankyou for your video it was very helpful. I’m getting a 150cc quad bike working that someone threw out. Many thanks and good bless
Thank you for watching my UA-cam video! Your support and engagement mean the world to me. I hope you enjoyed the content and found it helpful, informative, or entertaining.
Hello my friend the best thing to do is to buy a new magneto puller tool this happen to me 2 times because the metal of the tool is too soft and also the inside tread are to small next time you tight the puller tool try to tight as much as you can on the counter clock wise motion now there is also a problem that if the woodruff key on crankshaft steam is stuck you can try to spray a little WD40 in the center magneto shaft and tap the magneto with a rubber mullet last time I had to cut the magneto in pieces to remove it . Thank you for watching my video
Hello mohamed no you should not have any sound coming from the flywheel moving sound could came from your rear brake or inside the motor behind the flywheel but that will be more like a knocking sound
I'm having trouble getting the fan off. The bolts won't budge and when i try to apply force the whole motor turns. I don't have an impact drill. Can you offer any advice?
Hello spray little WD 40 at the bolt between the bolt and the fan put a socket 8mm on a drive amzn.to/3dqjxoy tap the drive with the hammer few time so the bolt will vibrate and you can unscrew the bolt
Hello the seat cover is great and last long time and when rain you do not get your back side wet price is only $10 on amazon dDanke Motorcycle Scooter Moped Seat Cover amzn.to/2yyIPAD
not the inside should be the same but make sure the stator is specifically designed for your scooter, as using one that generates too much AC voltage can damage the wiring and other components check with Rovira tinyurl.com/2pj7t4r4 and before you order ask questions but personally I will go with 11 if I have to choose. thank you for watching my video
My scooter would start with a loud CLANK!pretty ruff but it would start. Then I opened the flywheel and the stator was peeling , I cleaned it up a little and now it won't start at all.
Hello my friend you need to test the Stator with a multimeter there’s a possibility that you need a new stator sometime corrosion make stator shorting on ground
Hello my friend when something like that happen I try to read and analyze the belt because there is a possibility that the belt is rubbing or scratching somewhere or the rear clutch plates are warped and they wear the belt in a side way
Hello my friend i was wondering if you will perhaps know if a advance timing key will give a 150cc scooter more performance and thank you for all your videos they are very helpfull you are a scooter genius
I have all the tools I took my stator off because it was rattling I checked it nothing was loose but for some reason I keep hearing rattling what would be causing the rattling and what else could I check and what else could it be I would really appreciate an answer I love your Channel love your content I've been subscribed for a while and you help out a lot thank you so much
Hello Charles from that side of the motor you could ear the noise of the valves that make rattling sound and you can try to adjust them for clearance or you could have a problem with crank shaft bearing and that will be a bigger problem but the best way is to make a video when the motor is running if you have a little time and place that on FB chinese project scooter group and see if anybody else has the same problem
Mister virberello, please make for us a video to show how we replace the starter clutch behind the fire wheel, and a video to show how we replace the oil seal behind the variator cause I replace it without knowing the dimensions but it steal leak
That happened to me one time fortunately I was able to tight the removal tool harder and I was able to remove the flywheel there is other ways to remove the flywheel but you could damage the flywheel doing that
@@stefan6608 Hello I'm not to familiar with your scooter but you can try to reject your carburetor & have a air performance filter that will help a lot
Great video. What are the two wires going into the top of the magneto?
The wires connected to the magneto generally serve the following purposes:
Ignition Coil Wire: One of the wires is connected to the ignition coil. The ignition coil is responsible for transforming the high voltage generated by the magneto into an even higher voltage required to create a spark at the spark plug. This spark is essential for igniting the fuel-air mixture in the engine's combustion chamber.
Charging System Wires: The magneto also generates electrical power to charge the scooter's battery and supply power to various electrical components, such as lights, horn, and accessories. There may be wires connected to the magneto for charging purposes, typically consisting of a regulator/rectifier unit and other wiring related to the charging system.
Stator Pick-Up Coil Wires: The GY6 engine might also have a stator pick-up coil, which plays a role in determining the engine's timing and is used for generating signals to the CDI (Capacitor Discharge Ignition) unit. The CDI unit controls the ignition timing based on input from the pick-up coil.
Ground Wire: A ground wire might also be connected to the magneto, which helps dissipate any residual charge and ensures safety during maintenance.
Thank you for watching my video
@VirberelloScooterTips ok that is very useful knowledge 👌 👍 keep up the good work. Love the videos from the 🇬🇧
Please help...my flywheel tool does not screw in turning left it wants to screw in right but once I screw it in and tighten the back piece it was to strip off
Hello my friend try to tilt the scooter little bit on the left side spray a little of penetrating lube around the center shaft and let the scooter seat for one hour there is a possibility that the woodruff key inside the shaft is making resistance one time I had to cut my flywheel in small pieces and that is a lot of work. Thank you for watching my video
@@VirberelloScooterTips ok thanks for that I'll try it...and also on the 50cc the tool screws in to the right?
I want to say thank you for your videos I've been riding a scooter for going on the 15 years now he'll probably longer honestly I can't remember lol but your videos have helped me out so much and I really really appreciate it friend Thank you
You're welcome! I'm really glad to hear that my videos have been helpful to you over the years. It's amazing that you've been riding a scooter for almost 15 years, and your dedication to it is truly admirable. Whether it's been a long time or not, what matters is that you've found value in the content I create, and I appreciate your kind words and support.
Remember, the joy of riding a scooter comes from the passion and love you have for it. Keep enjoying the ride and exploring new adventures. If you ever have any questions or need further assistance, don't hesitate to reach out. Thank you for being a friend and a part of this wonderful community! Happy scooting!
my scooter only has spark sometimes could it be stator as cdi and coil seem fine4
Hello my friend sometimes when the coil gets old could be flickering or could be the pick up coil next to the magneto / Flywheel. Thank you for watching my video
I have solved my problem. When i put my cdi in the freezer it starts no problem.
Great video buddy and nice looking scooter. Finally someone that wears gloves while working on their scooter 😂
Hello Matt thank you for watching my video
Thank you!! You have helped me a few times. I want to ad that we appreciate you!! You explain everything so very good!!
I will always come to your channel for any help with our scooter! Bless you and have a great day!!
Hello my friend thank you for watching my videos and I’m very happy I was able to help you
Woodruff key - that's the name of the half moon key in the key way seat that locates the rotor (flywheel) to the crankshaft.
Great Terry thank you for your help
What is size of the puller i have 125cc
Hello my friend many gy6 150 cc have the same size flywheel of the 125cc
What do I do if the magnet on the pole coming out to the flywheel is lose ?
Hey buddy.. have a question.. what is the tread size or Inner diameter of the tool I need to buy for a YB50QT-3 - 3 4 stroke 50 CC we went to the Yamaha dealer and he gave us one to big in size.. 2015/04
Hello my friend honestly I'm not sure the best is to call parts for scooter in Florida check this tinyurl.com/34mkp5mk
Thank you!! God bless
I have to take the hole side off to replace seal and gasket. I will have to order flywheel puller as well. Very helpful thanks!
Hello Balisong thank you for watching my video
Hello from Perth western Australia! Thankyou for your video it was very helpful. I’m getting a 150cc quad bike working that someone threw out.
Many thanks and good bless
Thank you for watching my UA-cam video! Your support and engagement mean the world to me. I hope you enjoyed the content and found it helpful, informative, or entertaining.
Virberello i accidentally cross threaded my magneto puller tool,what can i do now
Hello my friend the best thing to do is to buy a new magneto puller tool this happen to me 2 times because the metal of the tool is too soft and also the inside tread are to small next time you tight the puller tool try to tight as much as you can on the counter clock wise motion now there is also a problem that if the woodruff key on crankshaft steam is stuck you can try to spray a little WD40 in the center magneto shaft and tap the magneto with a rubber mullet last time I had to cut the magneto in pieces to remove it . Thank you for watching my video
@@VirberelloScooterTips thank you very much
I got one of these my stator
went bad and the puller is tighting right not left it's a 24mm
Hello my friend the best is to contact parts for scooter in Florida in their website they have lots of puller
Sir how do you removing the flywheel by turning left i used all my strenght it wont screw in😅
does flywheel produce friction sound on moving?
Hello mohamed no you should not have any sound coming from the flywheel moving sound could came from your rear brake or inside the motor behind the flywheel but that will be more like a knocking sound
Do you have to take the motor out to get the flywheel off
Hello no just remove the fan an fan cover on the lower right side of your scooter
@@VirberelloScooterTips ok thanks
I'm having trouble getting the fan off. The bolts won't budge and when i try to apply force the whole motor turns. I don't have an impact drill. Can you offer any advice?
Hello spray little WD 40 at the bolt between the bolt and the fan put a socket 8mm on a drive amzn.to/3dqjxoy tap the drive with the hammer few time so the bolt will vibrate and you can unscrew the bolt
@@VirberelloScooterTips thanks. I'll give that a try
please tell me what seat cover or fabric you have on. it looks good!
Hello the seat cover is great and last long time and when rain you do not get your back side wet price is only $10 on amazon dDanke Motorcycle Scooter Moped Seat Cover amzn.to/2yyIPAD
@@VirberelloScooterTips thanks man!
If you get a 12-pole stator the inside diameter of the hole will be different than a six-pole stator.🤔
not the inside should be the same but make sure the stator is specifically designed for your scooter, as using one that generates too much AC voltage can damage the wiring and other components check with Rovira tinyurl.com/2pj7t4r4 and before you order ask questions but personally I will go with 11 if I have to choose. thank you for watching my video
My scooter would start with a loud CLANK!pretty ruff but it would start. Then I opened the flywheel and the stator was peeling , I cleaned it up a little and now it won't start at all.
Hello my friend you need to test the Stator with a multimeter there’s a possibility that you need a new stator sometime corrosion make stator shorting on ground
Hi my gy6 125cc belt is broken
Change 743 20 30 again 7 day after broken
Whats is problem ?
Hello my friend when something like that happen I try to read and analyze the belt because there is a possibility that the belt is rubbing or scratching somewhere or the rear clutch plates are warped and they wear the belt in a side way
Hello my friend i was wondering if you will perhaps know if a advance timing key will give a 150cc scooter more performance and thank you for all your videos they are very helpfull you are a scooter genius
The pick-up can be changed out its just a single separate wire
Yes you can 👍thank you for watching my video
I bought one today but mine threads to the right.. So I couldn't get it off.
I have all the tools I took my stator off because it was rattling I checked it nothing was loose but for some reason I keep hearing rattling what would be causing the rattling and what else could I check and what else could it be I would really appreciate an answer I love your Channel love your content I've been subscribed for a while and you help out a lot thank you so much
Hello Charles from that side of the motor you could ear the noise of the valves that make rattling sound and you can try to adjust them for clearance or you could have a problem with crank shaft bearing and that will be a bigger problem but the best way is to make a video when the motor is running if you have a little time and place that on FB chinese project scooter group and see if anybody else has the same problem
@@VirberelloScooterTips thank you so much appreciate the information keep up the wonderful work
Mister virberello, please make for us a video to show how we replace the starter clutch behind the fire wheel, and a video to show how we replace the oil seal behind the variator cause I replace it without knowing the dimensions but it steal leak
I did this and it just stripped the threads 😢
That happened to me one time fortunately I was able to tight the removal tool harder and I was able to remove the flywheel there is other ways to remove the flywheel but you could damage the flywheel doing that
I watching from Philippines
Niceee thank you for watching my video
Thanks again for the content
My pleasure!
Amazing video 😊💯👍
Hello my friend thank you for watching my video
@@VirberelloScooterTips Can you please tell me how can I make my Scooter faster please.
I have a Honda lead 100scv .. how can I make it faster...
@@stefan6608 Hello I'm not to familiar with your scooter but you can try to reject your carburetor & have a air performance filter that will help a lot
@@VirberelloScooterTips thank you 😊
Thank you ser you are a lifesaver
Hello my friend thank you for watching my video
Good video man👍🏽❤️❤️
Hello my friend thank you for watching my video
Nice tutorial Sir
Thank you for watching my video
thanks brother i need it a video like this
Thank you for watching my video
Excellent 💃 🎉
Thanks 🤗
Thanks
Hello thank you for watching my video
Good brooo ❤️❤️❤️
Thank you for watching my video