Good thing I said, "it'll make me look like an idiot if I didn't have to cut this." Thanks for the clarifcation Cynical. I changed the cards to read that, I pinned your comment, and updated the description so the second thing is that information. I can't wait for the dozens of comments telling me that I don't have to do that.
That's the nice thing about Yamix Worker stuff, they give you extra screws. In the event you have some that strip out the head or you loose one or two when you're assembling/disassembling your blaster for mods/repairs.
Just so it's said, the original Vector firearm, as well as the worker NERF kit, can take a flashlight above the barrel. There's also a spot below the Nerf barrel (where the real Vector barrel normally protrudes from the gun) that can be cut out and another sight or laser etc can be mounted there, making the side rails which I DON'T recommend (unless you want to glue/magnetize them in), unnecessary, as they can't really support much weight (real flashlight/laser sight) before dislodging and falling out... At least in my experience. Was going to point out the bit about the top rail, but someone beat me to it. Finally, a Vector Stryfe without an auto kit is nigh on blasphemy. Finish the job, Walrus. ^_^
Thank u for this installation on this stryfe cuz I did not know how to attach the mods so I researched how to install it but it always just showed reviews or something like that but then I found your installation so I say again thank u.
Where I live, Finland, the police actually ask before they shoot. If you ran outside with something like that, the police would come ask about it. If you started to shoot real bullets, then they would shoot back
@@inf1nity_yt I'm not a 100 percent sure how this actually works in USA, but I may know why the police acts so differently in those situations: 1. Finnish police training takes a long time. First you have to go to police school (3 years). Then you apply to become a police and I think you get more training after that. USA's training is bot as long but I still don't know how it actually works so I might be wrong 2. Second factor may be that more violence happens in USA than in Finland.
u could always paint or wrap the "suppressor" with orange tape. That should be good enough to make it safer and compliant with federal law for toy guns (6mm-wide blaze orange tip or a blaze orange stripe 1-inch (2.54 centimeters) thick on both sides of the barrel)
I got my Kriss Vector kit from NFStrike but it was really annoying to have to find all of the pieces on the website. This was before they were selling their sets for it. I can see the appeal of this listing though.
I did price-match their kits with this one, and if this one had those flip-up sights for a rounder 120$ price tag, this would beat the tar out of it. This is still a better deal (and from eBay, which I know some people have a problem with Lightake/NFStrike) this might just be the way to go if you're looking for one. Plus their pictures all have the magazine piece on backwards.
What do you think about the mediator xl (the mediator with the mediator barrel and stock with a double strike in it) I think it’s a beast blaster I love the shotgun barrel and the double strike stock
aw man from the thumbnail I was hoping they modified the kit to work with katana mags. Nope, just a thing to use a 6 round mag with an semi-auto blaster which would never be used outside of cosplay. :( really wish someone would make some mods that take advantage of the katana mags to look more like real SMGs while also being usable.
eaglestdogg the reason no one shoots flywheels with southwest slugs or half length darts is because is is less effective because their is less space for the flywheels to grip and fling forward so the darts would travel slightly slower
Thanks man didnt really expect an answer that fast but i thought to get one of these kits to My birthday i dunno why im just a big fan of guns even tho im just 12 Keep doing these kit videos they are awesome i thought of like the Scorpion evo one
I thought maybe i should get one of those kits plus a stryfe cause they look really cool but do you have any suggestions on cool but easy worker kits cause when i buy One its gonna be My first
do a BUZZ BEE BLASTZOOKA XBZ with a hopper side rail attached to a 14 dps rapidstrike then the other side with a BUZZ BEE BLASTZOOKA XBZ being a 6 shot shotgun
You put the top rail on backwards it has cut outs which mean you didn't have to mutilate your Stryfe
LMFAO.
Nein it be custom if it makes you feel better
Good thing I said, "it'll make me look like an idiot if I didn't have to cut this."
Thanks for the clarifcation Cynical. I changed the cards to read that, I pinned your comment, and updated the description so the second thing is that information. I can't wait for the dozens of comments telling me that I don't have to do that.
WalcomS7 lol
Cynical Manc n
26:14 Casually almost knocks over tripod and decimates the camera
Ivan Braginski very casual
Nerf: now in 8 different jigsaw puzzles
🤣🤣underrated comment
🪵
When the mod/kit is more expensive than the blaster itself
Screen Patch its looks cool tho
Thats almost always the case for high tier mods
Stonks
That's the case with better parts and internals.
It’s because it’s all 3-d printed
That's the nice thing about Yamix Worker stuff, they give you extra screws. In the event you have some that strip out the head or you loose one or two when you're assembling/disassembling your blaster for mods/repairs.
Just so it's said, the original Vector firearm, as well as the worker NERF kit, can take a flashlight above the barrel. There's also a spot below the Nerf barrel (where the real Vector barrel normally protrudes from the gun) that can be cut out and another sight or laser etc can be mounted there, making the side rails which I DON'T recommend (unless you want to glue/magnetize them in), unnecessary, as they can't really support much weight (real flashlight/laser sight) before dislodging and falling out... At least in my experience.
Was going to point out the bit about the top rail, but someone beat me to it.
Finally, a Vector Stryfe without an auto kit is nigh on blasphemy. Finish the job, Walrus. ^_^
Civilian version. Semi-auto only.
WalcomS7 lol touche.
@@nerformancemods5900 do you know what size of flashlight would fit?
Thank u for this installation on this stryfe cuz I did not know how to attach the mods so I researched how to install it but it always just showed reviews or something like that but then I found your installation so I say again thank u.
Slams magazine into the slot then hits it again. "He's dead Jim"
The "now its time to open up Quincy"😆
Thank you for doing this because I'm getting this same kit soon and I had no idea how to put in the extended mag release
Man, thank god I found this, I have no idea how to mod, but I really wanted a Vector kit, and then I found this, thank. God.
Where I live, Finland, the police actually ask before they shoot. If you ran outside with something like that, the police would come ask about it. If you started to shoot real bullets, then they would shoot back
That would be nice if U.S. police departments did that
@@inf1nity_yt I'm not a 100 percent sure how this actually works in USA, but I may know why the police acts so differently in those situations:
1. Finnish police training takes a long time. First you have to go to police school (3 years). Then you apply to become a police and I think you get more training after that. USA's training is bot as long but I still don't know how it actually works so I might be wrong
2. Second factor may be that more violence happens in USA than in Finland.
@@MikoTheGamer true. There is a lot more violence with gangs, shootings, and the “forgotten” epidemic of drugs
Maybe you could make a short vid about the removing of the inner barrel and replacing it?
I had to check this video out before buying one to see how to put it together and if it was really complex.
Nice video! thank you :)
Is it bad that I like the red longshot on the wall more than the blaster the entire video is about?
Joshua Greig No, red strike longshots are pretty.
where?! timestamp?
Yay you didn’t kill quincy
Could you do a Stefan dart mod on the stryfe and still put this kit on the same blaster?
Edit: Nvm I just looked up how each mod works
u could always paint or wrap the "suppressor" with orange tape. That should be good enough to make it safer and compliant with federal law for toy guns (6mm-wide blaze orange tip or a blaze orange stripe 1-inch (2.54 centimeters) thick on both sides of the barrel)
My AR stock, which came in with my kit, is an actual Magpul stock. Real milspec, real AR part. Pretty cool.
Do you need to mod the stryfe internals so the blasters work with the attatchments?
No internal mods needed to install vector kit
@@Oaken_head oh ok cool
@@jasontobias9537 the only internal mod needed is for the extended magazine release
i bought this kit it is amazing thanks for recommending i also went inside and made a 3 select modes
I have one stryfe do you recommend putting this on my only stryfe because I am not planning on buying another stryfe
Very late but yes. You can take it off pretty easy, so if you don’t like it then no worries.
Is this the project you were talking about Walcom?
Not at all. The project I'm gonna do requires sawing this thing in half :)
Would this kit work with the modulus stryfe remake? I'm almost certain modulus stryfe has a slightly different frame.
As far as I know it's identical.
Walcom S7 thank-you. Just wondering, because modulus is the cheapest stryfe variant on Amazon right now.
Modulus stryfe is exactly the same thing as a normal one, just in modulus colors
I got my Kriss Vector kit from NFStrike but it was really annoying to have to find all of the pieces on the website. This was before they were selling their sets for it. I can see the appeal of this listing though.
I did price-match their kits with this one, and if this one had those flip-up sights for a rounder 120$ price tag, this would beat the tar out of it. This is still a better deal (and from eBay, which I know some people have a problem with Lightake/NFStrike) this might just be the way to go if you're looking for one.
Plus their pictures all have the magazine piece on backwards.
+WalcomS7 Hm, makes sense.
And now Walcom’s following the average nerfer status quo. Congrats
Do u have to modify the stryfe in order to put on the kit or prevent jams
Yes
I'm going for looks so I believe it should be okay not to interfere with the internal modding for the magazine release right?
Yeah you are fine to leave the stock release. I did, prefer it actually.
Nerf designer: Its more like curse and look like lazer gun
Some designer that did this looking epik: realistic gun
What do you think about the mediator xl (the mediator with the mediator barrel and stock with a double strike in it) I think it’s a beast blaster I love the shotgun barrel and the double strike stock
Dunno, don't have any of it.
So, they sell the mag and barrel cover for 35$ on Amazon now, but some hunting will be needed if you want the whole thing.
I just went to Worker’s site and added everything I needed to my cart
Do you have any ways to remove striped screws?
drill them with a thinner drilling-rod. only way i found which does not damage the original hole.
Or use a star head driver, or a flat driver, the catch more
Question: What kind of rails are they?
I want to put a sight on mine but I don't know what kind I need for it to go on the rails?
KDH Gaming piciatinny rail
@@Destroryer125 is that the same as airsoft?
KDH Gaming yes
Thank you
KDH Gaming it's a pickiy tinny rail
Do you need the extended mag release?
Jackson Nuechterlein no
You don't NEED any of it, it just looks cool
I think this is the first time I have seen the complete kit done like that. Looks pretty nice, but not really to my taste.
Aww wish worker made 6 dart magazine but haz half vector mag so the 6 dart mag is hidden in the mag loading area
what scope is it ?
Does the stuff make the gun like faster and stronger or is it just for looks?
Just for looks
@@L_ightninng thank you
Is their a mod kit like this for a modulus
Do you have to change the magazine release or can you keep the stock magazine release?
You can keep it like it is said on the video.
Should I make one of these with half length darts, talon mags and full auto?
if you wanted to go for more of an actual vector you could use those katana mags for stephen's darts
If you use a Stryfe and attach all the attachments I will need to buy a hyperfire first to have more darts because it only has a six round dart mag
What if you make the stryfe like this, add the master key, the full auto flywheel?
Select fire too?!? That would be awesome.
Are the barrel adapters the same for every nerf stryfe mod kit?
Just got the vector pretty good kit to put on the nerf stryfe
Nobody:
Greg Renko: Dual wielding with sniper scope and shotgun barrel
I think this is a great video keep up the good work walcom
Nerf + Splatoon crossover on the Nerf side. Thoughts on how it could work?
Lol that would be cool
What screwdriver do you need to open the strife?
Philips head no1
The Marion art music 😂👌
There needs to be a scar kit for the rapidstrike I have a rapidstrike and I want a scar kit for it but as far as I know there isn’t a scar h kit
aw man from the thumbnail I was hoping they modified the kit to work with katana mags. Nope, just a thing to use a 6 round mag with an semi-auto blaster which would never be used outside of cosplay. :(
really wish someone would make some mods that take advantage of the katana mags to look more like real SMGs while also being usable.
eaglestdogg the reason no one shoots flywheels with southwest slugs or half length darts is because is is less effective because their is less space for the flywheels to grip and fling forward so the darts would travel slightly slower
Aren't they more accurate though? Also you can carry twice as many mags. Regardless though the tacticool factor alone would make it worth it :p
eaglestdogg same
eaglestdogg I feel the same way
Wait you can't add a bigger mag?
im going to wrap mine in orang dry carbon vinyl with some brushed black forged carbon
What if I do t want to replace the mag release does the stock one still work
TheRealJoey Yes, it will still work, with both the stock mag release and extended mag release.
Is the kit big?
The link to buy this doesn’t work anymore
How do you take the barrel out like you mentioned
I wanted to like the video why did you turn rating off
You can still like it.
I'm able to like the video, but the likes/dislikes aren't shown publicly. You can still help out by liking, you just can't see the numbers.
Me I can see the numbers
You don’t have to cut it. You put the top rail backwards. It widens on one end for that purpose
How did you get that optic sight
Where did you buy all this?
I’m so glad this guy is giving quality entertainment 🔫🔫🔫
Are you gonna be able to make it to Flagler?
Take away the barrel and the stock and you got an awesome looking pistol too
Hey how big is the Nerf rival Hades
Cool video I really want to do this myself
the funniest thing i noticed was that when he pause the video him self the de-jammer looked like the :o emoji
Can someone anwser me it will work without custom mag release??? 9:19
Yes.
@@WalcomS7 yay thanks
Can you Still shoot with it or is it just for cosplay?
Shoots just fine. Barrel reduces the range a little.
Thanks man didnt really expect an answer that fast but i thought to get one of these kits to My birthday i dunno why im just a big fan of guns even tho im just 12 Keep doing these kit videos they are awesome i thought of like the Scorpion evo one
I thought maybe i should get one of those kits plus a stryfe cause they look really cool but do you have any suggestions on cool but easy worker kits cause when i buy One its gonna be My first
Plus your actually the first UA-camr that has been kind enough to answer My question really apreciate it
You could just spray paint the tip orange so it looks fake
Do you have to take out the mag release
You have to to install the extended mag release, but if you don’t want/have the extended one, you don’t need to
Does it shoot?
Does it work with stefan darts?
Are they sold with real Hasbro Nerf Magazine?
No
*sees pricetag*
realizes i will never be able to get my hands on this
Will it fit on a modulus stryfe
Yes, it will. Any strife has the same proportions.
They should make a vector kit for the stryfe that makes it shoot have length darts
Nice
-Jack
I did buy a m4 kit on blaster parts
Can you link the sight?
I just want an M4 or Galil ACE 22 kit
Mr. Tangerine hvad er det for noget q
Mr. Tangerine o o. Mor. Du .
louise hansen speak English please.
Mr. Tangerine I'd like a propper P90 for Rayven or Zeus
notforsale today that wouldn't work but a p90 zeus would work in-fact someone already did it
But can you link the scope
Walcoms7 is a legend
Finally, Kriss Vector kit that uses short darts.
Edit: my disappointment is immesurable.
and ur day is ruined
They do have short dart conversion kits.
Is this MK8 music in the background? lol
do a BUZZ BEE BLASTZOOKA XBZ with a hopper side rail attached to a 14 dps rapidstrike then the other side with a BUZZ BEE BLASTZOOKA XBZ being a 6 shot shotgun
when people doesnt care about the nerf modification rule, MORE AWESOME NERF GUNS!!!!
We’re did you get the sight
E-Bay or Amazon
That piece that u didn't know what was is u can remove it to put a special flashlight in to
The striker from cod?
im getting it kfpr my bday but its almost out of stock me crying so sad
I hat sights can you use on the rail
put orange tape around the suppressor
Cool video 👍
RIP QUINCY
If it could take stefans you could use an angled katana mag
Man U wish I could do this but for the same price your could get an accurate B.B. gun but I get the concept
Love your vids!
Can you all those parts for less than $105??? Great vid. TkEZ»UK