Great tutorial, covered almost everything. Never worked on a cars electronics or took trim off before. It took me 6 hours working methodically, but it worked. It would be great if there was a tutorial for taking the sill trim off of a MK6 Golf.
Previous owner of my my 2012 GTI has removed rear wiper, there is a delete kit for that. I just wonder if I can take power from the connector of rear wiper? I am sure it has 12V and is fused...
Amazing video. Thank you so much, great video. The new golf 2020 doesn't have a reverse camera so this will look good on it. I can't understand why VW dosen't have offer for camera like this. How it's hidden is so cool
In the thick terminal of the car cables to the radio, have you had to remove the blue terminal that leads the yellow, green and gray cables to put the MIB connector. But then this terminal is left loose? Doesn't connect anywhere? Regards
Thanks for the video -- if I were to buy a higher resolution emblem camera to replace the existing emblem camera, could I just keep the existing wiring (adding necessary adapters if needed)? I have a 780 existing camera, but upgraded the head unit and the image is very blurry. I'm wondering if replacing the camera with a 1080 or higher would help that.
I just started this and when I replaced the badge with the new flip camera, I hooked up the normal lock power cable and had to close the trunk. It will not open now? Why not?
@@sxrrt well heres the answer.i Installed it and the whole badge gets replaced with a built in camera.The camera pops out everytime you put the gear in reverse and then hides again once the you stop reversing.so when you want to open the trunk you open it just like before so no there is no change really when it comes to opening the trunk!
@spongyjuniper5660 hi , the old badge was a botton to lift to open the tail gate ? After replacing it with the camera how would it be possible to open the tailgate mk5 golf 2008
in this case its not needed but in some cases you can connect camera power cable to it and other end goes to stereo where it has power + out for cameras so you dont need to ”borrow” power from revers light
The red wire on either end of the RCA video cable is just a wire that travels along the length of the cable. It can be used for different install requirements such as sending reverse light signal from rear of car to front of car for a after-market head unit that needs a reverse signal to trigger the display, (the VW factory harness provides a reverse trigger signal, so the red wire is not used), the red wire can also send Acc-12v from front of car fuse panel to rear of car to power the camera, (this guy used 12v from the rear of car like wiper motor, etc, so the red wire was not used). Simply, the little red wire is used to send power from front to rear or vice-versa. Most times it’s not used in factory setups, because the factory harness provides reverse signal to the head unit and the camera gets power from the reverse light.
That is exactly my problem atm. If I switch the cable on the badge with the one from car directly, it works after some tries, but it throws out the door, when camera flips up. When I switch to original cable and connect the car to the yellow/black cable, I can‘t open the trunk at all. One time I got that to work, but most tries didn‘t work out. Atm I have to open the trunk via the middle Button of my key… As I understand: the yellow/black cable get‘s the signal blocked, when in reverse gear, so the trunk doesn‘t „pop“. In my case the signal seems blocked all the time, no matter the ignition is on or off. Haven‘t figured out yet, how to get the opener to cooperate.
@@WesleyEayrs-p1m on my HU (cheap Android) there‘s a wire in the connection harness, which says „rear“. In my case it‘s delaying the closing of the camera a bit.
thanks for the video! Would you be able to tell me what model Golf this video was performed on? I have my reverse camera arriving tomorrow, and am just making sure I understand the fuse layout. My car is a 2012 MK6 GTI, and am wondering if fuse 16 (as you used in this video) would also work for my model. Thanks!
@@karimnusan9346 I could have SWORE I saw a video once (lost of course) of some like Russian guy installing another version, retrofit or ROW I don't know, but it didn't require cutting. I may have dreamed it. :(
Hey guys and girls I’m just wondering if these can be adjusted because mine seems like it doesn’t open enough because the red lines don’t show up and it just looks too far down. Can it be adjusted to look up more or something?
On the video shows positive and negative wires is going to fuse box,where i can get this special connection for the fuse box or where is the best to connect positive and negative wires?
from step 12 - 16 is it the left hand side because the driver side is the left? my car is right hand side so would i remove the panels on the right of my car? thanks
Do you happen to know how to get the timing shorter of it flipping back down after the car is out of reverse? Ours takes almost 30 seconds and if you turn the car off, it stays out til you turn it back on again.
I have an after market emblem (badge) rear view camera for VW Polo 2020 which I installed it but the Display shows that the camera is not ready. With RCA yellow cable is RED wire, do I need it to connect some where in positive that red wire?
Why it's needed to replace the drain pipe? Won't it disallow that the water that comes inside trunk to be pushed outside? Since it's now only connected to the VW badge? Also I saw that this camera has dynamic lines, do they change according to steering wheel? Thanks :)
Great tutorial, quick question, would like to do this for my mums 2005 mark 5 1.9TDI VW Golf, will camera connect to original head unit or will I have to update head unit. Thanks again
Thanks for the reply. I really dont know what type the original VW headunit is. It has buttons down each side of screen a cd player at top, it is not a touch screen. Is there some identification numbers on it somewhere?. Thanks again
@@colt11mitsi The flip badge camera it’s compatible with big screen radio units. Check the product details or ask the seller if you don’t know if it’s compatible. Sorry for the late response.
It looks like you unplugged the other blue connector to put in the RCA adapter, What are those other wires for? Isn't it possible to just take the RCA wires and add it to the already existing blue connector and keep everything plugged in? Also, how did you feed the wires from the driver side to the back of the head unit?
Hi! Maybe you can find the answer on our website: www.servicetutorials.com/en/2019/12/04/tutorial-how-to-install-flip-emblem-logo-badge-rear-view-camera-for-vw-golf-mk5-golf-mk6-jetta-in-just-27-steps/
They used a (foreign market) head unit that doesn’t utilize the original blue connector wires. But yes, instead they could have transferred the pins from new plug to the old plug.
Dear friend, the camera I bought for my Polo has a 5A fuse on the positive. My question is whether you can tell me which slot I should use. Do I need to connect a splitter with a 5A fuse to a slot already in use or do I have to find a free slot? Thank you
NRS510 I follow your step to connect, all are working but only the camera I see on display, the stereo look cannot rec'd my camera video signal, the blue plug, how to connect to stereo head unit? also the yellow video plug have a red cable, what are this one connect to? than you!
Hey i installed mine works well, but when I try to unlock the car, it doesn't unlock the boot unless I use the boot release button. Any ideas on how to fix or what the issue is.
Can someone help me out??? Where do I connect the red wire that is attached to the RCA cable?? My camera opens when I put it in reverse but I don’t video.
Hi! If you have a RCD330, you don't have to connect the red wire at anything, but you have to connect the blue wire from the power cable to the reverse wire from the tail light harness.
Great tutorial honestly thank you so much. 👍 Quick question how do you connect the MIB adapter to the quadlock harness it’s not that clear from the video?
Do you need to buy extra parts to attach the ground wire to the grounding bolt in the fuse box? It looks like you have the wire attached to a metal ring to contact the bolt, is that already in the car or something?
Hi! You can find all the information here: www.servicetutorials.com/en/2019/12/04/tutorial-how-to-install-flip-emblem-logo-badge-rear-view-camera-for-vw-golf-mk5-golf-mk6-jetta-in-just-27-steps/
Hey bro I did exactly what you did to my 2012 gti but I can’t get the camera work in the factory screen, it doesn’t show anything in the screen when I put in reverse but the camera is flipping,any advice what is the problem?
Great video and tuturial :-) I installed a carplay car radio and the same rear view camera but I have no signal on the carplay screen. I need a code to enter the carplay system settings and to configure the video signal (AHD, ...). Can anyone help me ? the carplay is a P2vw7001cp.
@TUTORIALEAUTO thanks for the video! Do you know where I can get this done as I don’t know the first thing about car electrics! i have the emblem unit with all the parts, but I just need someone to fit it! Any help will be great - I’m based in London but happy to travel somewhere, thanks
Question the flip camera for golf 2013 with RNS 315 sat & radio appears to be expensive at 500 euros , 5KO 827 469 AQ . I believe it is RGB video. Golf mark 7 flip cameras appear more numerous and cheaper but assume they cannot be used with mark 6 golfs as are different to RGB . Is this the case in that you have to stick with a specific mark 6 camera .
Awesome video, if I could give you 1,000 likes I would. I have one issue; when I put it on reverse the camera opens but I get a black screen, what did I do wrong??? Thank you very much for your time.
Cant you connect the the power to switch on gearbox older cars I worked on had switch that operated the reversing light when gear shift put into reverse push switch power reverse light on . ? Or is they cable some where in harness at front of the car in vicinity of the radio. New cars have lots electronic modiles control the electrics nowadays
Good evening, I bought a Fettoca rear view camera in the Vw logo to be installed on Android Auto Erisin. Despite having connected all cables as instructions. I always see black. Can you help me?
Hi, I have also the one from Fettoca (OBD Guidelines). If the black screen is with an error message "Camera not available" check the black video connection cable (plug/unplug again). If the camera flips but the image stays black, one of the two power cables for the camera is not connected to 12V properly. In my case I have 3 power cables *2 red and 1 blue. 1 is for the lock, the other two for the camera (+2 black for ground). I had both of the above mentioned Issues and could solve them with properly connecting the cables (make sure also that when the trunk is closed the reverse light is on). I am struggling with only one Issue now: The camera flips open on ignition (possible due to the reverse light check), after some time it closes automatically and functions as expected.
Hello! Maybe you need a time delay device box. Check the product details to see if your radio unit it’s compatible with rear view camera. Sorry for the late response!
@@Servicetutorials Hi, i've tried installing signal filter, which had no effect on the behaviour... My Radio is rcd330+ which is compatible with the camera and via vcds the camera is coded. I couldn't find the delay box as everyone says that rcd330+ doesn't need it... When the reverse light is not connected there is a video, but the badge doesn't flip, when the power is not connected the camera flips but there is no video and etc.
@@Alex-lw9cq you have to disable the cold diagnostic check with OBD2 (Golf 5) or VCP (Golf 6 - EEPROM), VAG Cars are checking all Lamps of funcitonality on ignition
@@VamteTamte26 thanks for the information. I have only OBD11, and was searching for this, but couldn't find it. I guess I will look for someone with VCP to turn off the cold check. Cheers!
I am looking to doing this to my mk6 golf, however, I also want to install the Alpine i902D-G6 head unit. I'm looking at the link provided to the aliexpress website with the trunk handles, but see a few different options for the mk6 golf. Would I need the RGB version to work with the Alpine i902D-G6? Or could I get the RCA version? If there is no option to work with the Alpine head unit, that is fine, but I figured there would be a way since the head unit is plug and play.
tried installing a VW flip camera on my 2013 VW CC using an aftermarket head unit, the head unit works, but I cannot get the camera to flip open. Any suggestions?
You may need VCDS to activate the feature and program your system to use it with the RNS 510. Not all radios have this feature available. You should research your radio's features before committing to purchasing this upgrade. Good luck.
Everything works great.... but the camera flips when I turn power on the ignition. It returns with no problem. Hatch opens with no problem when I unlock with the keyfob.
Hello i have a vw golf 6, I have installed an after market 2din radio (podofo) with canbus included. Can I wire the powercable to the back of the radio to the reverse wire (positive) instead of wiring to the fusebox?
Hi, Great video and I installed in the Golf 5. Camera power has constant 12V power and reverse wire I connected to the Head unit "reverse" wire instead of the reverse light. Work well but I have just one problem. If I switch to ignition ( dosn't matter I start the engine or not ) the logo come out like in the reverse mode ( shift is not in reverse ). After the "waiting" period go back. This is happened always after switch to ignition. Other case camera work well, stop the engine in reverse mode take out the key, camera goes back etc. I don't connect the red wire what is in the RCA connector based this label is for DVD. I also tested without ignition take out the camera fuse and put back bat in that case nothing happened. So camera goes out and back when I switch to ignition and I don't find why. Do you have the same issue ?
@@AnwarE13 Someone commented with this message as below. That's the only way to solve the issue. ----------------- @Daniel Bralic 1 year ago you have to disable the cold diagnostic check with OBD2 (Golf 5) or VCP (Golf 6 - EEPROM), VAG Cars are checking all Lamps of funcitonality on ignition ----------------- So the reason is when the car is started, it will do an diagnostic check to see if all the lights are working including the reverse light, which triggers the reverse camera
Bonjour, j’ai une Volkswagen Polo 5 de 2014 en fin de série. Savez-vous si je peux l’installer dessus ? Sachant que j’ai un autoradio Carplay avec option caméra de recul. Merci d’avance.
Good morning, I installed the aftermarket camera and everything works fine. The problem is that every time I turn on the ignition the camera opens for a short period, due to the check lights. Is there any way to solve it? It's annoying that it opens every time I turn the car on, even if reverse gear isn't in gear. Thank you
any Volkswagens have a function called light self-check. When you insert the car key, the car will start the light self-check to determine which bulb is damaged. If any bulb is damaged, the dashboard will show that the car bulb is damaged. This is a function that Volkswagen has opened for driving safety considerations. In this self-test, a current will be transmitted to the reversing light bulb to judge whether the light bulb is good or bad, and at the same time, this current will activate the flip motor.
That's exactly how it is. I researched it and came to the same conclusion. Furthermore, the byte (I think 19) is not configurable on my golf 6, and therefore it is not possible to disable the light check. Thanks for the reply
how do you move the wires from the fuse box to the radio? i can't figure it out, this is the only thing last to do. my kit is a little different i can't disconnect it I have to move all the wires from the fuse box to the radio.
Muhamed Besic Okay that’s strange, it leads me to think that you put the signal wire to a constant 12v but if you did not, i don’t know why it gives you this problems
Great tutorial, covered almost everything. Never worked on a cars electronics or took trim off before. It took me 6 hours working methodically, but it worked. It would be great if there was a tutorial for taking the sill trim off of a MK6 Golf.
Jamesley Dasse Thank you for your feedback!
There is a tutorial
Video is 16min and the work is 3 hours (or more) Good luck😂 been there, done that. Nice tutorial btw 😉👍🏼
Thank you for your feedback!
Is this compatible with golf 6 variant?
Good tutorial, but I don’t know if I can do this myself 😂🤦🏽♂️
Big Homie K You can try.
11:23 did you cut the wrong wire (blue) from your tail light?
Your content is so touching
Previous owner of my my 2012 GTI has removed rear wiper, there is a delete kit for that. I just wonder if I can take power from the connector of rear wiper? I am sure it has 12V and is fused...
Hello, great video! I'm looking for flip camera for Scirocco 2015 but I can't find it. Any ideas?
Amazing video. Thank you so much, great video. The new golf 2020 doesn't have a reverse camera so this will look good on it.
I can't understand why VW dosen't have offer for camera like this. How it's hidden is so cool
wins14 Thank you for your feedback!
seriously.. thats all my mk6 needs lol
Would this fit on a 2008 VW touran .?
In the thick terminal of the car cables to the radio, have you had to remove the blue terminal that leads the yellow, green and gray cables to put the MIB connector. But then this terminal is left loose? Doesn't connect anywhere? Regards
What fuse did you tap into?
The red wire that is on the yellow cable for video. Where does that cable go to?
Did you find out by any chance? I’m dealing with the same thing right now…
Thanks for the video -- if I were to buy a higher resolution emblem camera to replace the existing emblem camera, could I just keep the existing wiring (adding necessary adapters if needed)? I have a 780 existing camera, but upgraded the head unit and the image is very blurry. I'm wondering if replacing the camera with a 1080 or higher would help that.
I just started this and when I replaced the badge with the new flip camera, I hooked up the normal lock power cable and had to close the trunk. It will not open now? Why not?
Does the trunk open from the badje once the cam is installed?i have a golf 7 and the trunk opens by the emblem
had the same question
@@sxrrt well heres the answer.i Installed it and the whole badge gets replaced with a built in camera.The camera pops out everytime you put the gear in reverse and then hides again once the you stop reversing.so when you want to open the trunk you open it just like before so no there is no change really when it comes to opening the trunk!
@@spongyjuniper5660 thanks for that was it hard to install it?
@@sxrrt i didnt do it myself but from what i saw the hard part was the cable management
@spongyjuniper5660 hi , the old badge was a botton to lift to open the tail gate ? After replacing it with the camera how would it be possible to open the tailgate mk5 golf 2008
There is a short red wire on the RCA cable (RCD330 end). Where does that connect to?
That is a good question do you already know?
in this case its not needed but in some cases you can connect camera power cable to it and other end goes to stereo where it has power + out for cameras so you dont need to ”borrow” power from revers light
The red wire on either end of the RCA video cable is just a wire that travels along the length of the cable. It can be used for different install requirements such as sending reverse light signal from rear of car to front of car for a after-market head unit that needs a reverse signal to trigger the display, (the VW factory harness provides a reverse trigger signal, so the red wire is not used), the red wire can also send Acc-12v from front of car fuse panel to rear of car to power the camera, (this guy used 12v from the rear of car like wiper motor, etc, so the red wire was not used). Simply, the little red wire is used to send power from front to rear or vice-versa. Most times it’s not used in factory setups, because the factory harness provides reverse signal to the head unit and the camera gets power from the reverse light.
Good job.Thanks friend
Thank you too for the feedback!
how do you open the trunk after?
That is exactly my problem atm.
If I switch the cable on the badge with the one from car directly, it works after some tries, but it throws out the door, when camera flips up. When I switch to original cable and connect the car to the yellow/black cable, I can‘t open the trunk at all.
One time I got that to work, but most tries didn‘t work out. Atm I have to open the trunk via the middle Button of my key…
As I understand: the yellow/black cable get‘s the signal blocked, when in reverse gear, so the trunk doesn‘t „pop“.
In my case the signal seems blocked all the time, no matter the ignition is on or off.
Haven‘t figured out yet, how to get the opener to cooperate.
Will the camera install on the Passat (2012)?thinking of gifting this and a new stereo for my sisters car 🤔
That signal red wire on the RCA cable, where did you connect that?
@@WesleyEayrs-p1m on my HU (cheap Android) there‘s a wire in the connection harness, which says „rear“. In my case it‘s delaying the closing of the camera a bit.
Did u have R-Line Raul lights on?
Great video, everything works except the steering lines. Anyone know what needs to be done to get it working?
Did you cut the red wire with the fuse on and not put it back on?
Is this compatible with golf 6 variant?
thanks for the video! Would you be able to tell me what model Golf this video was performed on? I have my reverse camera arriving tomorrow, and am just making sure I understand the fuse layout. My car is a 2012 MK6 GTI, and am wondering if fuse 16 (as you used in this video) would also work for my model. Thanks!
Hi, Bob! The car uesd in the video is a 2010 VW Golf Mk6 1.6 TDI.
Any special programming needed to make the camera work on the stock radio?
This video is very usefull
!
Thank you for your feedback!
Thanks friend but how to activate the screen when you put revers gear??
I don't know what your asking but when you wire the reverse light as signal to turn on rear camera
good video.
i hv the camera but could not get all the cable harness . where can i purchase the cable set?
looking to do this for my polo 2014 - quick question, whats the drain pipe for into the badge? incase it rains?
mk5 golf has to have metal cut, right?
@erichill7560 thinking about doing it on mine, did you ended up doing it on yours? If so, how did it go!?
I haven't, and I don't want to cut. Still looking for a solution, but I'm heading for a separate cam.
@@erichill7560 No other solution than cutting. You also have to cut the wiper brace.
@@karimnusan9346 I could have SWORE I saw a video once (lost of course) of some like Russian guy installing another version, retrofit or ROW I don't know, but it didn't require cutting. I may have dreamed it. :(
@@erichill7560 Could've been for the Golf mk6. You can't physically fit the motorized badge without cutting.
Does the camera bump up against your fingers when opening the trunk?
Hey guys and girls I’m just wondering if these can be adjusted because mine seems like it doesn’t open enough because the red lines don’t show up and it just looks too far down. Can it be adjusted to look up more or something?
Hi! I think not.
@@Servicetutorials that sucks I’ll probably have to get another one then
On the video shows positive and negative wires is going to fuse box,where i can get this special connection for the fuse box or where is the best to connect positive and negative wires?
The best way is to put them like I do in the Video tutorial.
from step 12 - 16 is it the left hand side because the driver side is the left? my car is right hand side so would i remove the panels on the right of my car? thanks
So i have an Mk6 GTD and I dont have an camera on the back, I can still install this right ?
Yes, you can.
@@Servicetutorials Even if I dont have an camera right now ? 😄🤗
hi can i install emblem without connecting to 12v power supply? Will opening work for me? i want to install it in stages. Thanks.
Do you happen to know how to get the timing shorter of it flipping back down after the car is out of reverse? Ours takes almost 30 seconds and if you turn the car off, it stays out til you turn it back on again.
I am not sure but I think you should use a VCDS (VAGCOM) dyagnose to do that.
Vous avez ou le garage de quelle ville merci
Directions with camera says pover from ACC -accessory line, not Constant.
Would you please elaborate on that?
the lines didnt show up on my screen, whats the red wire connected to the rca cable plugged into the radio for?
Can you change the camera to a better quality one?
I don’t know if there’s a new camera with a better quality for VW Golf MK6 model.
Can you still open the boot with the emblem
Yes, of course. It will work in the same way with the old one.
Can we make this at home by using original parts?
Yes, you can.
I have an after market emblem (badge) rear view camera for VW Polo 2020 which I installed it but the Display shows that the camera is not ready. With RCA yellow cable is RED wire, do I need it to connect some where in positive that red wire?
which radio unit did you use to connect the back flip camera to?
RCD330G
Why it's needed to replace the drain pipe? Won't it disallow that the water that comes inside trunk to be pushed outside? Since it's now only connected to the VW badge?
Also I saw that this camera has dynamic lines, do they change according to steering wheel? Thanks :)
How did you get the RCA (video) cable from under left plastic part of the car to behind the radio head unit?
You can do it with your bare hands, but you need another person to help you to reach the cable.
Great tutorial, quick question, would like to do this for my mums 2005 mark 5 1.9TDI VW Golf,
will camera connect to original head unit or will I have to update head unit.
Thanks again
Hello! What kind of original head unit you have?
Thanks for the reply.
I really dont know what type the original VW headunit is. It has buttons down each side of screen a cd player at top, it is not a touch screen. Is there some identification numbers on it somewhere?.
Thanks again
@@colt11mitsi u might need a new head unit
@@colt11mitsi The flip badge camera it’s compatible with big screen radio units. Check the product details or ask the seller if you don’t know if it’s compatible. Sorry for the late response.
It looks like you unplugged the other blue connector to put in the RCA adapter, What are those other wires for? Isn't it possible to just take the RCA wires and add it to the already existing blue connector and keep everything plugged in? Also, how did you feed the wires from the driver side to the back of the head unit?
Hi! Maybe you can find the answer on our website: www.servicetutorials.com/en/2019/12/04/tutorial-how-to-install-flip-emblem-logo-badge-rear-view-camera-for-vw-golf-mk5-golf-mk6-jetta-in-just-27-steps/
They used a (foreign market) head unit that doesn’t utilize the original blue connector wires. But yes, instead they could have transferred the pins from new plug to the old plug.
That red cable that goes with the yellow RCA where does it go ???? I installed everything but that cable is loose
Did you figure this out? I have the same thing.
@@zuidkb7312 Same...
@@emrekonuk1525 Saammmeee
@@mrlele6580 just tape it off so it touches no metal. If you hook power up via your fuzebox and the 3rd short cable to the reverse light. It will work
Dear friend, the camera I bought for my Polo has a 5A fuse on the positive. My question is whether you can tell me which slot I should use.
Do I need to connect a splitter with a 5A fuse to a slot already in use or do I have to find a free slot? Thank you
Bel video grazie
Grazie!
Hey do you have a link for the camera pls ? I’m from there UK and I owe a golf GTI mk5
Hello! You can find here: bit.ly/31s5KZJ
TUTORIALE AUTO thank you!! And is this a reliable seller and will it 100% work with my car ?
@@xFuSioNClan97 you have to check if your radio unit is compatible with the flip badge camera. Check the product details or ask the seller.
TUTORIALE AUTO I have a after market RCD330 plus headunit with car play and reverse screen
Did the car screen have a backup camera setting or does it come up by itself when you install it
When you buy a rear view emblem camera, you have to have a RCD330G or something similar to work and you don’t have to install nothing.
Do they have one for the mk7
You know if there's a way to install flip camera on Passat Variant b7?
We don't know. Sorry!
I wanted to ask the same question...
First I must say very good video, I like to know did you replace an old camera or this was a new installment?
Georgie Porgie Hi! This was a new installment.
@@Servicetutorials I’ve got a unit that needs fittings but not sure where to go to get it fitted. Can you assist? Happy to travel, I’m in London
NRS510 I follow your step to connect, all are working but only the camera I see on display, the stereo look cannot rec'd my camera video signal, the blue plug, how to connect to stereo head unit? also the yellow video plug have a red cable, what are this one connect to? than you!
Hey i installed mine works well, but when I try to unlock the car, it doesn't unlock the boot unless I use the boot release button. Any ideas on how to fix or what the issue is.
Hi! I don’t know, sorry. Maybe you have to check the wires from the boot.
Can someone help me out??? Where do I connect the red wire that is attached to the RCA cable?? My camera opens when I put it in reverse but I don’t video.
Hi! If you have a RCD330, you don't have to connect the red wire at anything, but you have to connect the blue wire from the power cable to the reverse wire from the tail light harness.
TUTORIALE AUTO yes I did that just as your blog said but I still don’t get video on the camera.
I get a message that reads “Rear View camera system is currently not available.
@@mv.m5438 Please, follow these steps: www.servicetutorials.com/en/2019/12/04/tutorial-how-to-install-flip-emblem-logo-badge-rear-view-camera-for-vw-golf-mk5-golf-mk6-jetta-in-just-27-steps/
@@mv.m5438 did you solve your problem?
Great tutorial honestly thank you so much. 👍 Quick question how do you connect the MIB adapter to the quadlock harness it’s not that clear from the video?
Do you have a link for the set you are installing?
Yes. You can find the product here: bit.ly/39HnenQ
Hi! If you are from Europe, UK, you can buy it from here: amzn.to/35enA3d
If you are from US, you can buy it from here: amzn.to/34OVGuw
Would this work on 2012 VOLKSWAGEN JETTA S
If you have a flip emblem on the back, yes, it will work.
How do you get the distance grid lines to show
Salut merita sa montez un rcd 360 pro 2 în loc de rns 315? Seat leon 1p
Good video where can I get that badge camera kit from....!
Hi! If you are from Europe, UK, you can buy it from here: amzn.to/35enA3d
If you are from US, you can buy it from here: amzn.to/34OVGuw
I picked up one from eBay for $150
Fit on Jetta 2013 to?
@@freshogs_ You have to check if your radio unit it’s compatible with the rear view camera badge. Check the product details.
Do you know if this camera is compatible with a kenwood ddx?
Hello! You have to ask the seller or you can check the product details.
Good video, gives all details, if I run the pawer fuse straight to radio power supply will it still work perfect?
I tried it and didn’t but I don’t have VCDS enable for rear camera
I powered mine from radio supply and it work perfect, brown and red wire, brown for negative (-) and red for positive (+)
Where are you from?
Romania
@@Servicetutorials come to germany and make this in my car
@@MX-ii2ye 😁
Do you need to buy extra parts to attach the ground wire to the grounding bolt in the fuse box? It looks like you have the wire attached to a metal ring to contact the bolt, is that already in the car or something?
Hi! You can find all the information here: www.servicetutorials.com/en/2019/12/04/tutorial-how-to-install-flip-emblem-logo-badge-rear-view-camera-for-vw-golf-mk5-golf-mk6-jetta-in-just-27-steps/
do the lines onscreen move with your steering wheel?
Yes
TUTORIALE AUTO Does that require 2 additional CANBUS wires installed into the harness, that you did not show ?
will this work with a 2012 VW Tiguan S?
Hey bro I did exactly what you did to my 2012 gti but I can’t get the camera work in the factory screen, it doesn’t show anything in the screen when I put in reverse but the camera is flipping,any advice what is the problem?
Did you have to install a “ Delay box”? And if you did could you please do a video on how to install?
97jackbmx You don’t need a delay box for this rcd330g unit.
@@Servicetutorials will you need one for rcd330+ (earlier unit). Also I'm getting a black screen instead of camera image, any ideas?
@@adamdiamond0 I get black screen that says camera not available. Did you solve this?
Please help! I installed everything but when i put in reverse the camera closes in a few seconds.. and also i have a fault in my back up rear light
Great video and tuturial :-) I installed a carplay car radio and the same rear view camera but I have no signal on the carplay screen. I need a code to enter the carplay system settings and to configure the video signal (AHD, ...). Can anyone help me ? the carplay is a P2vw7001cp.
@TUTORIALEAUTO thanks for the video! Do you know where I can get this done as I don’t know the first thing about car electrics! i have the emblem unit with all the parts, but I just need someone to fit it! Any help will be great - I’m based in London but happy to travel somewhere, thanks
Also in London. Have you sourced one?
@@SpicyPumpkin99 yes based in London. Currently being quoted £200 to fit it. I’ve got the part, just need it fitted.
No, sorry
C'est possible sur Polo 2011
Question the flip camera for golf 2013 with RNS 315 sat & radio appears to be expensive at 500 euros , 5KO 827 469 AQ . I believe it is RGB video. Golf mark 7 flip cameras appear more numerous and cheaper but assume they cannot be used with mark 6 golfs as are different to RGB . Is this the case in that you have to stick with a specific mark 6 camera .
How would I know if the reverse camera will work with some head unit which had Apple car play?
Hi! You have to read the features of the product before you buy it.
Awesome video, if I could give you 1,000 likes I would. I have one issue; when I put it on reverse the camera opens but I get a black screen, what did I do wrong??? Thank you very much for your time.
Hi! If you have a RCD330, you have to connect the blue wire from the power cable to the reverse wire from the tail light harness.
Cant you connect the the power to switch on gearbox older cars I worked on had switch that operated the reversing light when gear shift put into reverse push switch power reverse light on . ? Or is they cable some where in harness at front of the car in vicinity of the radio. New cars have lots electronic modiles control the electrics nowadays
I have the same issue
Good evening, I bought a Fettoca rear view camera in the Vw logo to be installed on Android Auto Erisin. Despite having connected all cables as instructions. I always see black. Can you help me?
Hi, I have also the one from Fettoca (OBD Guidelines).
If the black screen is with an error message "Camera not available" check the black video connection cable (plug/unplug again).
If the camera flips but the image stays black, one of the two power cables for the camera is not connected to 12V properly. In my case I have 3 power cables *2 red and 1 blue. 1 is for the lock, the other two for the camera (+2 black for ground). I had both of the above mentioned Issues and could solve them with properly connecting the cables (make sure also that when the trunk is closed the reverse light is on).
I am struggling with only one Issue now: The camera flips open on ignition (possible due to the reverse light check), after some time it closes automatically and functions as expected.
Hello! Maybe you need a time delay device box. Check the product details to see if your radio unit it’s compatible with rear view camera. Sorry for the late response!
@@Servicetutorials Hi, i've tried installing signal filter, which had no effect on the behaviour... My Radio is rcd330+ which is compatible with the camera and via vcds the camera is coded. I couldn't find the delay box as everyone says that rcd330+ doesn't need it... When the reverse light is not connected there is a video, but the badge doesn't flip, when the power is not connected the camera flips but there is no video and etc.
@@Alex-lw9cq you have to disable the cold diagnostic check with OBD2 (Golf 5) or VCP (Golf 6 - EEPROM), VAG Cars are checking all Lamps of funcitonality on ignition
@@VamteTamte26 thanks for the information. I have only OBD11, and was searching for this, but couldn't find it. I guess I will look for someone with VCP to turn off the cold check.
Cheers!
Can you switch to OPS view?
What is OPS?
@@Servicetutorials optical parking system, view with parking sensor graphics
I am looking to doing this to my mk6 golf, however, I also want to install the Alpine i902D-G6 head unit. I'm looking at the link provided to the aliexpress website with the trunk handles, but see a few different options for the mk6 golf. Would I need the RGB version to work with the Alpine i902D-G6? Or could I get the RCA version?
If there is no option to work with the Alpine head unit, that is fine, but I figured there would be a way since the head unit is plug and play.
Hello! You have to ask the seller for the details.
tried installing a VW flip camera on my 2013 VW CC using an aftermarket head unit, the head unit works, but I cannot get the camera to flip open. Any suggestions?
Same issue you every find the problem
Can you install this on mk5 Jetta with rcd330?
Hi! Before you buy the flip rear view camera, check if it’s compatble with your rcd330. Check the details from the product.
Does this method apply for the VW Eos and will it work right off the bat if connected to the RNS 510 radio ?
You may need VCDS to activate the feature and program your system to use it with the RNS 510. Not all radios have this feature available. You should research your radio's features before committing to purchasing this upgrade. Good luck.
Did anyone need to code in the camera or did it work without?
Everything works great.... but the camera flips when I turn power on the ignition. It returns with no problem. Hatch opens with no problem when I unlock with the keyfob.
I’m having the same issue
robert kamber The vendor sent me a filter relay? Supposed to fix it apparently. Still waiting for it to arrive from China.
albert427 what do we do with the relay
Where do you wire the relay to?
97jackbmx what relay
Hello i have a vw golf 6, I have installed an after market 2din radio (podofo) with canbus included. Can I wire the powercable to the back of the radio to the reverse wire (positive) instead of wiring to the fusebox?
No it won’t turn off with the car
Hi, Great video and I installed in the Golf 5. Camera power has constant 12V power and reverse wire I connected to the Head unit "reverse" wire instead of the reverse light. Work well but I have just one problem. If I switch to ignition ( dosn't matter I start the engine or not ) the logo come out like in the reverse mode ( shift is not in reverse ). After the "waiting" period go back. This is happened always after switch to ignition. Other case camera work well, stop the engine in reverse mode take out the key, camera goes back etc. I don't connect the red wire what is in the RCA connector based this label is for DVD. I also tested without ignition take out the camera fuse and put back bat in that case nothing happened. So camera goes out and back when I switch to ignition and I don't find why. Do you have the same issue ?
Have you solved your problem? If yes, how?
I’ve got the same problem with mine. Any help please
@@AnwarE13 I think the only way is as others said, program the car NOT to do the automatic lights checking
@@michaelyimingqiu sorry what do you mean by that?
@@AnwarE13
Someone commented with this message as below. That's the only way to solve the issue.
-----------------
@Daniel Bralic
1 year ago
you have to disable the cold diagnostic check with OBD2 (Golf 5) or VCP (Golf 6 - EEPROM), VAG Cars are checking all Lamps of funcitonality on ignition
-----------------
So the reason is when the car is started, it will do an diagnostic check to see if all the lights are working including the reverse light, which triggers the reverse camera
Bonjour, j’ai une Volkswagen Polo 5 de 2014 en fin de série.
Savez-vous si je peux l’installer dessus ?
Sachant que j’ai un autoradio Carplay avec option caméra de recul.
Merci d’avance.
I did what you did. My trunk opens, but when in reverse the camera doesnt flip.
Good morning, I installed the aftermarket camera and everything works fine. The problem is that every time I turn on the ignition the camera opens for a short period, due to the check lights. Is there any way to solve it? It's annoying that it opens every time I turn the car on, even if reverse gear isn't in gear. Thank you
Same with my car
any Volkswagens have a function called light self-check. When you insert the car key, the car will start the light self-check to determine which bulb is damaged. If any bulb is damaged, the dashboard will show that the car bulb is damaged. This is a function that Volkswagen has opened for driving safety considerations. In this self-test, a current will be transmitted to the reversing light bulb to judge whether the light bulb is good or bad, and at the same time, this current will activate the flip motor.
That's exactly how it is. I researched it and came to the same conclusion. Furthermore, the byte (I think 19) is not configurable on my golf 6, and therefore it is not possible to disable the light check. Thanks for the reply
where do you get those plastic pry tools from??
Hi! You can find them HERE: amzn.to/30b9Ofx
Hello. Does anybody know if it's possible to get the camera a little cheaper somewhere? Every site I looked they're 100€ or more...
Does this work with oem vw infotainment screen on 2017 polo?
Just take the infotainment screen out and check the back of it to see if it has an input for the camera
how do you move the wires from the fuse box to the radio? i can't figure it out, this is the only thing last to do.
my kit is a little different i can't disconnect it I have to move all the wires from the fuse box to the radio.
The fuse wires connect to the camera emblem not the radio. Only the RCA plug port adapter connects to the radio.
my camera opens immediately as soon as I turn on the ignition , is that normal?
I think you have wired the signal wire for the flipping mechanism to a constant 12v, you have to wire it to your backup light
@@wiljandejong7594 I connected everything the same way as on the video, it is the same with him, watch at 16:00
Muhamed Besic Okay that’s strange, it leads me to think that you put the signal wire to a constant 12v but if you did not, i don’t know why it gives you this problems
@@wiljandejong7594 Yes it is on number 16 in Fusebox
Same problem here, did you find a solution ?
So this cannot fit in a mk5?
Jarno Geerdink Yes, it can.