How To Remove A Gib Key hit and miss engine
Вставка
- Опубліковано 11 жов 2024
- ,,, just a little something for that blank page in your book, pencil it in,, hit and miss engine repair, going to be sparks, weld flash, loud noises, oil spatter, and smoke, all on a rainy day,,, could ask, what did you do today, the bread and butter for a job shop, GIB KEY REMOVAL,, said wait a minute,, you got a John Deere type e,,,, how you going to get that key out, leave a comment, subscribe, pass it on
We spent 2 full days wrestling with a gib key that was on our Hesston baler. It stuck out about an inch beyond the end of the shaft (A MISTAKE). We used a cape chisel, heated it up, you name it, it would not budge. Last night after coming in from the shop frustrated and at our wit's end, we found your video. This morning, ( day 3), after splicing a 5/8" bolt on the end of the key and welding 2 5/8's bolts on either side, we used a 2" pipe and a 3/8" plate (with a hole it it), and double nutted the bolt. Had to use a 3 foot, 3/4" drive Snap-On ratchet to turn it. We crossed our fingers. I'm happy to say that the gib key surrendered, and has been removed! Thank you so much for sharing your ideas and knowledge. You're a genius!
Rodney & Pam Sequeira
Willow Creek Angus
Caldwell, Idaho
,,, I be working on valve guides next, thanks
Thank you so much Sam. I’m at a point where I need to pull my first flywheel and didn’t know where to start before watching your video. Now I have a game plan
I had 208 Fairbanks and C96 continental's running pump Jack's. A few witties. Pumping 400 bbls of oil per day. I'm impressed to see someone intersected in restoring old engines. Old E42 Ajax impress me.
CMA Ajax. Got any. I would love to see you restore some of these. I love to see expert's work on these engines. I'm a old timer. Bethlehem and Steel mechanic.. Back in the Day's.
I’m going to be doing this in a few weeks. I hope I have the same success. Your knowledge is much appreciated.
Excellent Sam! So glad to see! How about cooking some of them bologna sandwiches again? For old time's sake? Please take care, stay safe..
Can't beat that; excellent shop class lesson today.
A sight to behold. Got my welder's helmet on in the nick of time! Penciled it all in my notebook. Dogeared the page. Nice work SDS!
Another fine job, Sam. keep up the good work.
Hmmm, well, Sam, it was easy in principle. Took some pretty clever convincing, though. Thanks for letting us watch.
I know I am late to the party but I have been building a house the last year. I had a 5HP Fuller & Johnson where the key wouldn't budge. I ended up pressing the flywheel on farther with an attachment I built to remove the key. I used 2" x 1/2 steel, two pieces of 5/8 all thread and a 2" 1/4 wall tube. It worked also
Very enjoyable watch Sam, thank you.
Excellent job as always that’s how it gets done. If I need to know how to do something I’d watch your videos I’m sure I could do it then. Kinda neat to see you working on a different brand of engine. Thanks 😊
mr sam i miss videos when you was cook pie with ham with two glass of water. my mom like your vids too.
I have a old engine that powered pump Jack's. I would love to see it run again. Setting in a shack on the oil lease.
Nice one SDS... you came a bit close to my nose with that damn hammer though.....
Nice demo!
entertaining as always Shopdog
Good job
Good one!!
Brilliant!
Sam don't you think that beard is a fire hazard when welding:-))
that probably felt pretty satisfying to get out
Sweet! Pretty amazing how the penetrating oil you used made it as far in along the key as it did. Once you removed the key it appeared wet. Good stuff--was it PB Blaster? I know you like to use that stuff.
free all and pb used them both
Retired want a John Deere powering a Ice cream freezer On a cart less than 10k. Can you do it? Challenge. I'll pay it. Dual ice cream freezer?
👍👍💯💯🇺🇲🇺🇲
See my last comment on last vido