Having this much power with so little skills required used to be a dream now you can literally build any hardware with a bit of programming knowledge using these modules.
BINARY UPDATES makes a useful point in an earlier comment: The TX pin on the UNO connector is connected to the *RX* pin on the chip that communicates with the PC. UBLOX datasheet says TX is an output from its chip, so TX-TX means we're connecting the output of the GPS to the input of the USB converter, which is correct. If you wanted GPS to talk to the Arduino instead of the PC, then you'd need to swap TX/RX. As far as I can tell, the PCB doesn't swap the names, but I remain to be convinced of that..
I think I've seen the Arduino/gps trick before, 2 or 3 years ago. Today somehow I had everything trashed out and you helped me find my way out of the jungle, thanks :-)
This video is well explained. But Facepalm after 5 minutes. If you use the 3.3 Volts from the arduino, cause the neo 6m module is only 3.3 volt toleranted, then use a levelshifter for the tx line aswell. The arduino will send the data via tx pin as a 5volt signal bro.
Hi Binary Updates. Thank You for the good detailed information on the Ublox NEO-6M gps module. I am going to buy this exact module for a Chromebook that have converted to Android-x86 to use as a dedicated tablet for a drone flying app. I am going to crack open the Chromebook and hopefully be able to figure out a UART location to solder the appropriate pins to along with the 3.3 VDC supply pad,,for module. From doing a lot of reading on these GPS modules there are always manual configurations you have to enter in a couple config files in linux. Have never actually found a how to on Android,which is surprising. Hopefully I can make it work.
Hi Refayet, I may continue this series later to interface GPS module with Arduino Uno. probably next month as i'm doing very busy these days. I hope you understand.
While the power delivered to the NEO 6M can be 5 volts since it has an onboard voltage regulator, the data lines do not allow for 5 volts and unless a voltage divider or line level shifter are incorporated the voltage of the UNO data lines will destroy most of the NEO 6M's in time.
Hi Ronald, Its possible considering lots of Arduino board these days come in market with poor design and power issues. I've used quality Arduino and because of good power and grounding my NEO-6M Ublox GPS Module has tolerated voltage. And it worked in my case without causing any damage to GPS Module. There are so many cheap clones with loosely designed board. And these board needs to be careful with.....This is just my opinion. By the way thanks for sharing. Have a good day
On voltage levels, as far as I can tell the module does accept 5V supply as it has a regulator. But UBLOX says the the data isn't 5V tolerant. It's 3.3V CMOS, 3.6V absolute max. The module doesn't add any protection to the TX/RX lines. For breadboarding, I'd stick a 1k resistor in series with each line.
Question: If the light doesn't turn on on the neo6m, does that mean I shorted it out? I'm still getting values from the SM, they just don't make any sense.
hello, can you answer some questions please 1. this module can work out without an arduino micropocessor? 2. can we send the data to some like mobile or to the web, what do we need to do? 3. does it have a cost to use the satellites, or work with like wifi o is just put the battery and thats all? 4. can we modify the base code and save them inside the gps module? thanks in advice for your time
My daughter tried to connect gps to arduine but could not get any responce. The light ddid not show The connection was correct as per yours but no signe of responce. I tried to help her withe soldering the 4 jumpers and i checked the ohm and the are all 4 pins connected. Is this normal or may be the medual is deffected?
Hi Virendra, it'll work all over the world. As this GPS Module NEO-6M will locate nearby satellite anywhere on the planet to fetch latitude and longitude data. I hope you enjoyed watching this video. Best wishes!
Does this module have different version? At 4:35 When you connected ground wire, the led immediate lit up. Mine doesn't. Anyway, I get gps data from serial port. So it's fine right? Also how long does it take for GPGLL to complete? I left it on for 5 minute and still got incomplete data.
Hi Pal, I've used Ublox NEO-6M Module in the video lesson. The ability of GPS module to take GPLL data depends on location where you've placed GPS Module. If its place in open space where GPS module finds satellite quickly then you get GPLL data quickly otherwise it takes time to get exact data. Now how long is bascially depends on place again where you're testing your module
Hello, i connected my gps module with my esp8266 for the first time it worked but after that I'm not getting the latitude and longitude it's showing 0.000000 for both, even though led is blinking, I'm getting this problem, what's the solution for this??
Hi Darshan, try to place GPS module outdoor in open space. The issue you're facing is because your Module maybe not able to locate satellite....I hope this may help. Good luck!
I have some questions for you: What is the GPS module supply voltage on this video ? 3.3v or 5v ?? Do you easily have problems to get satellites fixes ? Since you are indoor.. ?? Where is your clock located in the house ? 1rst floor ? Basement ? Do you use GPS repeater to get sat signals ? I built 2 clock GPS driven using another type of GPS module than the NEO-6M and I'm having a hard time to get satellites signals.. Thanks !
hello every one, I have two questions: 1 how accurate is this gps? 2 Which solution do you propose for some one who needs a precise positioning( maybe with an error equal to 2 cm at most) with respect to some fixed objects marked by a transmetter of signal
Late reply i know, this unit seems accurate to 2.5m on horizontal position. for something with 2cm accuracy you will need something with a ZED-F9P module. they are accurate to 1cm but come at a high cost.
Hello Sir. Could you make a video on how to use arduino with gps to turn on or off a relay based on speed detected. I'll like to have a gps control relay to turn some lights on in my car when current speed is 10mph. Thank you.
You advise me what type of GBS modules that will be compatible with a Bluetooth module and at the same time an SD card . You can advise me because I'm a little lost thank you
hello is it possible to collect and read the gps data to a cloud using this arduino and neo-6m gps module? how can i do that? Would be grateful for your kind response. Thanks.
Hi I am having a connections problem with the GPS module and the Arduino, the Arduino always got shutdown when I try to connect the GPS module, specifically when I connect it to the power (5V), I believe it is a problem in the power distribution, plz help me fix the problem 😫🙏🏻
Usually it takes sometimes around 4-8 Minutes for me. The outdoor satellites is quick to connect and for indoors it takes quite long to connect. i recommend you to sit near window if in case you Ublox NEO-6M GPS Modules takes time to through GPS cordinates. Wish you good day.
Sir i have done the connections as per ur circuit. but the LED module does not glow on the module. plz help me.i am working on the project related to GPS module. this is the second module. but am not able to understand the problem
I am using a UART to TTL USB to test my GPS, I keep on getting the raw data your were getting at first. I have waited many minutes but my GPS is not getting any signal. What could be the problem
Hi Tinotenda, Make sure the baud rate of serial communication with default baud rate of your module if you're using USB TTL Converter. Also, change the location. Try to test in outdoor means in open space where it would be easy for GPS Module to get signal. I hope this may help you
No, It will not ruin your module. The reason to unplug Tx and Rx while uploading code is because Arduino uses those pins. Once the upload is done then Tx, Rx pins will be free to connect to any external devices like GPS NEO-6M Module in this case. I hope this answers your question. Good luck and best wishes!
Did this module just worked right out of the box ? or you've to configure it first? Cuz mine one doesn't even power on and nothing shown on serial monitor :(
you have to send data to any local server using GPRS and your application to local server and you can access the data from any location. and i suggest use GSM 900A module for GPRS.
Sir I tried to connect gps and arduino with different connections still my GPS didn't got any signal(I have ordered a new gps still..) Can u plz help me out? 🙏🙏🙏🙏
Hi Sami, Usually it takes time to find satellite but try and test in open space once. If it can help to get data from GPS Module. Otherwise its possible that module may have issue
@@BINARYUPDATES thank you for replying , i searched what you said about hot/cold start and it helped me to understand how it works , now i do a cold start before starting my ardusat project then everything goes ok after that in the hot start
Its may be because your NEO-6M GPS module not able to able to locate nearby satellite. You must try in open space or near windows. I hope this may help. Good luck and best wishes!
Yes, you can power Arduino and GPS Module over standalone battery and it will still work. Once you upload arduino code you no longer need to stay connected to your PC. I hope this may help you. Good luck!
Hi Aman, you can use Nano version of Arduino with GPS Module to read data. The thing is all you need is to use Serial Tx and Rx Pin on Arduino Nano. I hope this may help you. Good luck!
Hi I've used arduino default sketch and connections uses very simple Tx and Rx Pins of an Arduino Uno to connect with GPS Module. Good luck and best wishes!
Show how to build a little GPS tracker for Cars or Bycycle. Mini Arduino 32 bit .. + GPS Bauteil (GPS6MV2)) + Arduino Battery Slot = U blox Programm forthe Live data, map
Hi Pratik you can use GSM Module which usually comes with GNSS support. This will let you track your vehicle and send data to cloud using mobile data network. I hope this may help you. Good luck!
what a brave man to give his exact position and data for free
Who cares where he lives
@@rajawikiaa pakistan and taliban does
@@kartikagarwal99 so sad to hear this from you. Kindly focus on the technology how we gonna use it in a better way.
@@Muhammadkhan607 Sorry for that
@@rajawikiaa its not about who care s , it just about how he is honestly :)
Having this much power with so little skills required used to be a dream now you can literally build any hardware with a bit of programming knowledge using these modules.
10:47 Not gonna expose my location, but here's my exact GPS coordinates
Yea Im a secret agent man I must keep hidden! ha
Layer of obfuscation if one lives in 50 story building.
yes it takes atleast 6 decimal number after point and then it trace the exact location
BINARY UPDATES makes a useful point in an earlier comment:
The TX pin on the UNO connector is connected to the *RX* pin on the chip that communicates with the PC.
UBLOX datasheet says TX is an output from its chip, so TX-TX means we're connecting the output of the GPS to the input of the USB converter, which is correct.
If you wanted GPS to talk to the Arduino instead of the PC, then you'd need to swap TX/RX.
As far as I can tell, the PCB doesn't swap the names, but I remain to be convinced of that..
Can you please elaborate, I'm still new in this so didn't understood much but I think what you are saying might be helpful to my project.
I need gps tracker coding for Arduino or NodeMCU
I think I've seen the Arduino/gps trick before, 2 or 3 years ago. Today somehow I had everything trashed out and you helped me find my way out of the jungle, thanks :-)
This video is well explained. But Facepalm after 5 minutes. If you use the 3.3 Volts from the arduino, cause the neo 6m module is only 3.3 volt toleranted, then use a levelshifter for the tx line aswell. The arduino will send the data via tx pin as a 5volt signal bro.
Thanks dear a lot.I was in the dark world of GPS clock.Ur video find out my path.Again thanks.
Glad it helped
3:13 Isn't there a 3.3V LDO regulator connected next to module jumpers. So technically you can connect the module VCC directly to 5v too.
yes you can connect Vcc to 5 volts.
@@bilal1708 can you please elaborate what you both are trying to imply
*some one knocks on door* I used your GPS info, I thought I could ask for advice in person
We Americans feel the need to f with people for no reason... it's called mental illness
Oh holy Indian tutorial man, I request utmost assistance.
Thank you for this (very) clear introduction !
Hi Michel, you're very welcome!
Best Wishes
Hi Binary Updates. Thank You for the good detailed information on the Ublox NEO-6M gps module. I am going to buy this exact module for a Chromebook that have converted to Android-x86 to use as a dedicated tablet for a drone flying app. I am going to crack open the Chromebook and hopefully be able to figure out a UART location to solder the appropriate pins to along with the 3.3 VDC supply pad,,for module. From doing a lot of reading on these GPS modules there are always manual configurations you have to enter in a couple config files in linux. Have never actually found a how to on Android,which is surprising. Hopefully I can make it work.
How much did it take for you to get the full line of data?
Mine has been on it for about 5 mints and I don't really see much progress!
Hi, It seems this series is not continued. Please give me with links if you published further videos on coding for GPS.
Hi Refayet, I may continue this series later to interface GPS module with Arduino Uno. probably next month as i'm doing very busy these days. I hope you understand.
While the power delivered to the NEO 6M can be 5 volts since it has an onboard voltage regulator, the data lines do not allow for 5 volts and unless a voltage divider or line level shifter are incorporated the voltage of the UNO data lines will destroy most of the NEO 6M's in time.
Hi Ronald,
Its possible considering lots of Arduino board these days come in market with poor design and power issues. I've used quality Arduino and because of good power and grounding my NEO-6M Ublox GPS Module has tolerated voltage. And it worked in my case without causing any damage to GPS Module. There are so many cheap clones with loosely designed board. And these board needs to be careful with.....This is just my opinion. By the way thanks for sharing. Have a good day
Thanks for shareing your knowledge i'm using the same GPS Module for Sole projects ;-)
On voltage levels, as far as I can tell the module does accept 5V supply as it has a regulator.
But UBLOX says the the data isn't 5V tolerant. It's 3.3V CMOS, 3.6V absolute max.
The module doesn't add any protection to the TX/RX lines.
For breadboarding, I'd stick a 1k resistor in series with each line.
Thanks Mr. Epi for your valuable advice and comment. I appreciate you time to write. Thanks
I was about to ask about that Tx pin and was worried it'd fry the board. Thank you very much.
This would be very useful on my rockets, if I could make my unit smaller...always gotta search for em
Hey I am here for the same reason haha
I believe it's tx to rx & rx to tx.... transmit goes to recieve
Question: If the light doesn't turn on on the neo6m, does that mean I shorted it out? I'm still getting values from the SM, they just don't make any sense.
I Connected GPS RX TO ARDUINO TX AND TX GPS TO ARDUINO RX, still works, also, wired on rx GPS 2 resistors 1k and 470 for ground
hello, can you answer some questions please
1. this module can work out without an arduino micropocessor?
2. can we send the data to some like mobile or to the web, what do we need to do?
3. does it have a cost to use the satellites, or work with like wifi o is just put the battery and thats all?
4. can we modify the base code and save them inside the gps module?
thanks in advice for your time
Bro got something to ask u , if I connect my arduino uno + arduino gps with using battery ? I'm still can get data in my laptop ?
Pls help me I'm urgent
My daughter tried to connect gps to arduine but could not get any responce. The light ddid not show
The connection was correct as per yours but no signe of responce. I tried to help her withe soldering the 4 jumpers and i checked the ohm and the are all 4 pins connected. Is this normal or may be the medual is deffected?
Thanks man, this information is golden :)
Thanks Mjallux for your comments. Wish you a beautiful day Cheers
After uploading the program in this module, can we track anywhere this module's position in India or the world ?
Hi Virendra, it'll work all over the world. As this GPS Module NEO-6M will locate nearby satellite anywhere on the planet to fetch latitude and longitude data. I hope you enjoyed watching this video. Best wishes!
@@BINARYUPDATES Ok but to get data from this module, we will need to connect this module with any internet source ?
stumbles across your post, very interesting ,well done and thanks for sharing.
Hi Mr. Bruce, Glad you enjoyed it
@@BINARYUPDATES this method is not working can you plz provide programming one
Is the location of the piece determined at the moment? Or experience talking about the itinerary of the trip to and from?
Thankyou for this wonderful video. I have learned a lot thanks to you =D
Thanks a lot sir, very well explained though I am still waiting for the NEO-7M GPS module to arrive
I'm sure you gonna have good time with your NEO GPS Module with Arduino Projects. Have a Fun..Cheers
Good work bro, s video ne channel subscribe krny py majbor krdiya, 😇, keep it up.
Thanks and welcome Brother. Good Luck
Thank god
I am shocked that I wasn't able to connect antenatal
Does this module have different version? At 4:35 When you connected ground wire, the led immediate lit up. Mine doesn't.
Anyway, I get gps data from serial port. So it's fine right? Also how long does it take for GPGLL to complete? I left it on for 5 minute and still got incomplete data.
Hi Pal, I've used Ublox NEO-6M Module in the video lesson.
The ability of GPS module to take GPLL data depends on location where you've placed GPS Module. If its place in open space where GPS module finds satellite quickly then you get GPLL data quickly otherwise it takes time to get exact data. Now how long is bascially depends on place again where you're testing your module
Hello, i connected my gps module with my esp8266 for the first time it worked but after that I'm not getting the latitude and longitude it's showing 0.000000 for both, even though led is blinking, I'm getting this problem, what's the solution for this??
Hi Darshan, try to place GPS module outdoor in open space. The issue you're facing is because your Module maybe not able to locate satellite....I hope this may help. Good luck!
bro ur so smart and explain clearly
perfect description good job man
Hi Alireza,
Glad you think so!
I have some questions for you:
What is the GPS module supply voltage on this video ? 3.3v or 5v ??
Do you easily have problems to get satellites fixes ? Since you are indoor.. ??
Where is your clock located in the house ? 1rst floor ? Basement ?
Do you use GPS repeater to get sat signals ?
I built 2 clock GPS driven using another type of GPS module than the NEO-6M
and I'm having a hard time to get satellites signals.. Thanks !
Voltage supply of the GPS module is 2.7-3.6V as you can see at it's chip's datasheet www.rlocman.ru/i/File/2011/04/22/1.pdf
Bro I live in viman nagar 😂 Revell orchid society
hello every one,
I have two questions:
1 how accurate is this gps?
2 Which solution do you propose for some one who needs a precise positioning( maybe with an error equal to 2 cm at most) with respect to some fixed objects marked by a transmetter of signal
Late reply i know, this unit seems accurate to 2.5m on horizontal position. for something with 2cm accuracy you will need something with a ZED-F9P module. they are accurate to 1cm but come at a high cost.
Hello Sir. Could you make a video on how to use arduino with gps to turn on or off a relay based on speed detected. I'll like to have a gps control relay to turn some lights on in my car when current speed is 10mph. Thank you.
Now I can finally track down that guy who keeps asking for my social security
How are you going to hide this monstrosity? It consists of 3 God damn boards!
@@armincal9834 11:19
Amazing video.. To get knowledge about GPS module
You advise me what type of GBS modules that will be compatible with a Bluetooth module and at the same time an SD card . You can advise me because I'm a little lost thank you
My GPs is not blinking
I am not getting any blinking on the GPS module. Want could be the issue ?
It may be because you GPS Module couldn't track or find satellite. You can try change place preferably in open space you can test if it helps....
Great video I have learnt many key points
Great video! Thank you for educational explanation
Hi Christian, thank you so much!
Glad to know you found this GPS NEO6M video useful
Wish you a beautiful day!
Question when the Module doesn’t light up no more it means it’s fried right?
😂
how to install gps neo 6-m antenna?Is it a plug-in model or is soldering required? Thank you.
Hi Muhammed, GPS antenna comes with its connector which can be easily plug-in to Ublox NEO-6M Module. We don't need to solder it on Module
@@BINARYUPDATES Thank you
I was able to attach your antenna
hello is it possible to collect and read the gps data to a cloud using this arduino and neo-6m gps module? how can i do that?
Would be grateful for your kind response. Thanks.
Hi I am having a connections problem with the GPS module and the Arduino, the Arduino always got shutdown when I try to connect the GPS module, specifically when I connect it to the power (5V), I believe it is a problem in the power distribution, plz help me fix the problem 😫🙏🏻
How much time takes to search satellite? I am not getting that long string.
Usually it takes sometimes around 4-8 Minutes for me. The outdoor satellites is quick to connect and for indoors it takes quite long to connect. i recommend you to sit near window if in case you Ublox NEO-6M GPS Modules takes time to through GPS cordinates. Wish you good day.
Sir i have done the connections as per ur circuit. but the LED module does not glow on the module. plz help me.i am working on the project related to GPS module. this is the second module. but am not able to understand the problem
I am using a UART to TTL USB to test my GPS, I keep on getting the raw data your were getting at first. I have waited many minutes but my GPS is not getting any signal. What could be the problem
Hi Tinotenda,
Make sure the baud rate of serial communication with default baud rate of your module if you're using USB TTL Converter. Also, change the location. Try to test in outdoor means in open space where it would be easy for GPS Module to get signal. I hope this may help you
What happen if we don't unplug the rx and tx connection when uploading? Does it ruin the module?
No, It will not ruin your module. The reason to unplug Tx and Rx while uploading code is because Arduino uses those pins. Once the upload is done then Tx, Rx pins will be free to connect to any external devices like GPS NEO-6M Module in this case. I hope this answers your question. Good luck and best wishes!
Very good presentation
thanks man, this video helped me alot! :D
Where can I buy neo 6m GPS module, I've searched Aliexpress seems like they are having fake ones...
Hi any chance you can show how to set up a 10mhz frequency standard (10mhz lock)
Cheerz
a clear step by step tutorial
It help me a lot, thx
Hi Cesaramirruizcorces, I'm glad to know this GPS interfacing tutorial was useful. Have a good day!
Did this module just worked right out of the box ? or you've to configure it first?
Cuz mine one doesn't even power on and nothing shown on serial monitor :(
Turned out, mine one was faulty. Got a new one that worked out of the box.
Thank you very much. Very very good explanation.
Glad you liked it
where's part 2 of the video to parse the longitude and latitude?
RX pin to RX pin?
How can i send the real time gps location to my application
you have to send data to any local server using GPRS and your application to local server and you can access the data from any location. and i suggest use GSM 900A module for GPRS.
you can input the NMEA messages from a GPS receiver into your application and parse specific messages (such as $GGA) for time of day.
You could even send the data in JSON format using web socket
Sir I tried to connect gps and arduino with different connections still my GPS didn't got any signal(I have ordered a new gps still..) Can u plz help me out? 🙏🙏🙏🙏
Did try connecting gps out in open?
tx goes to rx
Hi there , i have a question please, i use the same module but sometimes it takes up to an hour , is something wrong with my module?
Hi Sami, Usually it takes time to find satellite but try and test in open space once. If it can help to get data from GPS Module. Otherwise its possible that module may have issue
@@BINARYUPDATES thank you for replying , i searched what you said about hot/cold start and it helped me to understand how it works , now i do a cold start before starting my ardusat project then everything goes ok after that in the hot start
Very clear elaboration 👌
Thank you 🙂
Great information and presentation 🙂
Hi Mr. Prasad, Glad you enjoyed it!
@@BINARYUPDATES can we have the data continuously displayed on Google maps when this sensor is mounted on a moving object?
Thank you! Helpful video!
Waiting for 10 minutes, but still have not got the full nema sentence yet, does that mean my neo 6m is broken? Please someone help.
Its may be because your NEO-6M GPS module not able to able to locate nearby satellite. You must try in open space or near windows. I hope this may help. Good luck and best wishes!
When you connect the arduino with the gps without uploading the program and the gps does not turn on does that mean it's not working?
You must upload default Arduino code as i shown in video lesson. And if connections are right then you must see GPS data in serial monitor
red led not blinking after connecting with vcc ,gnd ,rx,tx of gps module to arduino .is gps module not working?
I suppose it works as long as you can see NMEA sentences on the serial monitor.
Facing same issue
@@meetalisharma8920 hey first time use GPS module in wide open area and wait for 10 minute it will work
@@abhirajroy2235 thank you!! It's working now 😄
@@meetalisharma8920 👍👍
can we have the location even if the Arduino is not connected to the PC
Yes, you can power Arduino and GPS Module over standalone battery and it will still work. Once you upload arduino code you no longer need to stay connected to your PC. I hope this may help you. Good luck!
@@BINARYUPDATES thank you so much
Thanks for explic this !!!
Hi Lulian, welcome !
Nice, easy explanations
Thanks bro. Really helpful.
Can I use this for my scooter ?
Yes you can use it with Scooter but just as an DIY Device
@@BINARYUPDATES so it won’t be reliable
Nice man😀😀
Now I know where do you live I am comming to your house
Is It accurate for indoor navigation ?
Is it unlimited range and can we also use it for feet detection for module rocket
Yes you can use NEO-6M GPS Module for your project!
Heh heh you were late but thank you 😅actually we are working on a different project our last one was done 👍 it worked.
Please post the next video of displaying the latitude and longitude in the serial monitor
technoelectronics44.blogspot.com/2020/09/neo-6mgps.html
Can i use aurdino nano inplace of uno
Hi Aman, you can use Nano version of Arduino with GPS Module to read data. The thing is all you need is to use Serial Tx and Rx Pin on Arduino Nano. I hope this may help you. Good luck!
@@BINARYUPDATES thanks sir
Can we track location using Ip adress of the module
Does it require internet to track position
Hi Sai, GPS Module especially NEO-6M Module doesn't require internet for reading latitude and longitude data.
very useful, thanks!
Glad it was helpful!
You can send all the appendices from the documents and programs of the project
Hi I've used arduino default sketch and connections uses very simple Tx and Rx Pins of an Arduino Uno to connect with GPS Module. Good luck and best wishes!
My module is sending data continuously but satellite is not capturing i have wait more then one hour but failed
I just wanna ask if there is voice command/record in it that will where the direction of a specific place?
I hope someone can answer me
Thanks
it is taking more than 5 minutes to display stagnant coordinates ? What to do ?
Show how to build a little GPS tracker for Cars or Bycycle.
Mini Arduino 32 bit .. + GPS Bauteil (GPS6MV2)) + Arduino Battery Slot = U blox Programm forthe Live data, map
Can it use in bike without Internet?
Nyimak
May i connect it with multi wii
your links are not working,please help .
what if you upload a code and the rx tx is still connected i accidently upload it does the module now is broken?
someone please answer
No module will not get affected
are you getting these data in indoor environment?
Hi Mohimangonj
Yes, I have tested my NEO-6M GPS Module with Arduino indoor while shooting this video lesson. I hope you enjoyed watching video
is this need any internet ? or gprs or sim ?
No need of Internet/gprs/sim since its just GPS Module
How to send data to cloud ? On Our own server. If we don't have wifi in vehicle ?
Hi Pratik you can use GSM Module which usually comes with GNSS support. This will let you track your vehicle and send data to cloud using mobile data network. I hope this may help you. Good luck!
@@BINARYUPDATES means we have to add Sim card ? And also monthly datapack recharge ?
Thank u sir pls make a video with apm 2.6 with same gps
Yes, I'll be coming up soon publishing videos on Drone and relates APM 2.6 with the GPS Module