how can we make the buzzer keep buzzing until it is reset the person can pass the beam quickly and you might not be sure you heard a beep and also the sound will probably make them run away
No that would require a capacitor, this is just a simple potential divider system with Vout being controlled by a ldr, the current going into the base gets amplified which helps get a better frequency for the buzzer at the collector
Patrick! U think u could make same circuit adding a mechanism to let buzzer beep continuously until resetting it...therefore adding a reset switch ! ???
+BEES Gab I tried that but it gives me no more than 2 seconds. I would like it stay on for 20 or 30 seconds.I can use a DPDT Relay and make I stay on till reset, but like I said I would like it to stay on 30 seconds and then reset itself (without Arduino)
excuse me but im getting it in the reverse order!!! when the laser hits the LDR it lightly beeps if nothing is shone to the LDR there is just silence pls tell the solution
Replace buzzer with input if 555 time in monostable mode. Output from 555 drives the buzzer instead. The resistor and capacitor in the 555 will determine how long the buzzer stays on.
The technical explanation is not correct. An npn base to emitter juntion acts as a diode and will not allow the voltage to go to 4.5v as is mentioned in the video. It will stay at about 0.7..0.8v,. Instead of vbe to go to 4.5v, the base-emitter current will increase and active the npn.
Great video. Thanks a lot. How do we make this buzzer to stay on until a reset button is pressed?
Please advise
Laser security system is my first experiment .this is a good experiment in Electronics.
how about if we make it continuous alarm what kind of transistor we need ??????? plssss answer
can i have a look of how the 5v battery looks plss?
how can we make the buzzer keep buzzing until it is reset the person can pass the beam quickly and you might not be sure you heard a beep and also the sound will probably make them run away
why don't u add capasitor to regulator 7805 ?
You are using a laser... so what do safety curtains normally use?
I built the same circuit and unable to get it to work... Whats the amps on the power Supply?
hi just want to ask if you have any tutorial how to make a simple remote controlled alarm. a simple on and off alarm. =)
May i use BC547 transistor?
Can we use a PNP transistor instead of a NPN transistor? If no, then pls explain the reason.
Yes you can buddy
could you make a flip flop beeper with N2222A? ( beep-beep-beep instead of constant beeping?)
what LDR did you use ?
Can I use 2N2222A transistor by replacing the 2N2222 transistor??? Please help me...😌
Why don't you specify what caint of buzzer you are using active vs passive.
can I use 2N7000 transistor for the circuit?
pls reply soon
look at the datasheet of both to be sure
Whats the main principle ?
Is it RC series circuit?
No that would require a capacitor, this is just a simple potential divider system with Vout being controlled by a ldr, the current going into the base gets amplified which helps get a better frequency for the buzzer at the collector
Awesome! Nice, clear and concise. Thanks for making it simple.Cheers,LD
Partick, where I can buy the LDR 1K light -100K Dark? I have been looking on line but I have not found it yet. Is it ok if I use a LDR 5K-100k?
How to convert to 12v
Any way to have the opposite, The buzzer silent and when the beam is broken, it will sound?
I think it is possible, try to move the BUZZER in serial with the LED receiver (LDR)
Use pnp transistor or interchange the LDR and the 10k resistor.
Patrick!
U think u could make same circuit adding a mechanism to let buzzer beep continuously until resetting it...therefore adding a reset switch ! ???
Use an SCR which will stay on until grounded. Alarms are popular applications for SCRs.
can i use bc547 transistor instead of 2n2222?
Sure you can, it is one of its equivalents, especially in this case
Hi Patrik Is there a way to make it stay on for a few seconds after the laser hits the LDR?Or is there a way to make it stay on, until a manual reset?
+dana miller add some 555 timer
+BEES Gab I tried that but it gives me no more than 2 seconds. I would like it stay on for 20 or 30 seconds.I can use a DPDT Relay and make I stay on till reset, but like I said I would like it to stay on 30 seconds and then reset itself (without Arduino)
excuse me but im getting it in the reverse order!!! when the laser hits the LDR it lightly beeps if nothing is shone to the LDR there is just silence
pls tell the solution
mee too
It was your mistake in ldr or transtor
One quick question, instead of using a laser, can we use LED's for it? just wondering.
yes of course, but laser is for big distance
LED produces a much weaker beam. A divergent beam.
Sooo good.Very clear and looks simple. Really useful...
hy ,can any body plz tell me how to shield LDR from stray light?
Put it in darkness place
can i put a PNP transistor instead of NPN?
how to keep the alarm beeping for a few seconds?
Replace buzzer with input if 555 time in monostable mode. Output from 555 drives the buzzer instead. The resistor and capacitor in the 555 will determine how long the buzzer stays on.
Can I use a photo diode instead of LDR? If yes then how??
Abhiti Sachdeva both are same...
How to add 555 timer
This is my 1st project in my college
I am tried this but didn't work
Nice vid, good explained and simple!
Brilliant just what I needed, thanks
Thanks Very Much bro. I made one with help of your video.
thank you for sharing your knowledge.....
Thanks for the great video
Great. Love you, bro.
i love u you r a genius
dont't ........ shut up u fool
very thnxxx
the greatest results that I have had was by using the Gregs Electro Blog (just google it) without a doubt the most useful course i've followed.
The technical explanation is not correct. An npn base to emitter juntion acts as a diode and will not allow the voltage to go to 4.5v as is mentioned in the video. It will stay at about 0.7..0.8v,. Instead of vbe to go to 4.5v, the base-emitter current will increase and active the npn.