@cblack1863 Thanks! No foam for me lol. When I was working out of my other box as an aircraft structure mechanic, it was foamed. I'm slowly phasing that out.
Awesome nice set up my dad had a ltd like that tuna boat could burn the tires off l think it had 429 in it and no l was not brake standing thanks for sharing
@howardsutton3502 Thanks for watching and commenting! If it was a 67, it was likely the 428. I can't wait to get this going again. Should be a nice cruiser with plenty of torque.
Killer set up! Only suggestion I have is swap out the fixed wheels on the cart to swivel casters so all 4 wheels spin. Makes it much easier to maneuver around the shop and harbor freight usually has them in stock for $7 each. . I just did mine a couple weeks ago.
Item number 69852 That’s the wheels I used for my 4 drawer tech cart. Was a direct bolt on, even reused the original hardware. Just used a jack to lift up the cart a little and swapped the wheels out. Took 10 minutes. Totally worth the $15 and no more parallel parking the tool cart 😆
Really nice setup. I have a 4 drawer cart that I have packed to the gills. Literally more tools than most guys have in 2 carts lol. Love seeing a guy using cheap tools. Can't wait for more videos, I do some myself on another channel.
@larrydudgeon2846 Thanks for watching and commenting! I try not to spend on expensive stuff if I don't need to. I've built and repaired plenty of stuff with less lol. Share your other channel, I would love to check it out!
@@critiical Thanks for taking the time to watch and comment! It's been through a few configurations over the years, but I think I finally have one I like.
@RAY44444 If I'm slinging stuff around, I usually move it to the lid for any open container. I keep water bottles nice and low so my old self can slide over and grab it without getting up off the floor lol. Thanks for watching and commenting!
@Benzene3686 Thanks for the feedback. I noticed it was a bit off sounding, and I think it was my fault [poor positioning]. The prybars are a great deal!
@Carterthielftw_ I started with a set from the Yard Store when I was just getting into the aviation industry. Over the years, the bits have been replaced by the places where I worked. I couldn't find a brand on the bits, but here is the setup. www.yardstore.com/drill-bit-set-combo-fractional-letters-numbers-high-speed Thanks for watching!
@mavrik9475 Thingiverse.com under modular ratchet holders. There are many different types. If you aren't able to print your own, check out www.toolprintingtechnologies.com
Anyone organizing on the cheap? Casoman Socket Organizer is on crzy sale right now on amazon. Ordered trays for 1/4,3/8,&1/2 SAE & Metric for 14$ total - single listing. Peg Type like a Jensen socket trays if familiar. The setup in the vid is nicer for reaching down into. But for my non-production level work - hope these cheapies do the job.
@patricksquires77 I've never tried those, but I do have a lot of Goliath Industrial socket rails. I got them pretty cheap on eBay. They had a bunch of lower priced options that have held up decent. I think the magnet style like I have can be found for pretty cheap now too. A lot of different brands carry them on Amazon.
@techman7141 The green and black magnetic holders in the top are Ares brand. The others in the top are Ernst twist lock rails. There are links in the video description that will take you straight to them on Amazon 👍
Nice clean set-up man👍 great organization. Not needed, but I'm surprised you haven't caught that foam bug goin around, lol
@cblack1863 Thanks! No foam for me lol. When I was working out of my other box as an aircraft structure mechanic, it was foamed. I'm slowly phasing that out.
Awesome nice set up my dad had a ltd like that tuna boat could burn the tires off l think it had 429 in it and no l was not brake standing thanks for sharing
@howardsutton3502 Thanks for watching and commenting! If it was a 67, it was likely the 428. I can't wait to get this going again. Should be a nice cruiser with plenty of torque.
Very nice organization! You are making very efficient use of the space. Impressive.
@montestu5502 Thanks for the feedback!
Killer set up! Only suggestion I have is swap out the fixed wheels on the cart to swivel casters so all 4 wheels spin. Makes it much easier to maneuver around the shop and harbor freight usually has them in stock for $7 each. . I just did mine a couple weeks ago.
@willpierson5861 Thanks! Which caster did you go with? Direct bolt on? I've been meaning to do that mod.
Item number 69852
That’s the wheels I used for my 4 drawer tech cart. Was a direct bolt on, even reused the original hardware. Just used a jack to lift up the cart a little and swapped the wheels out. Took 10 minutes. Totally worth the $15 and no more parallel parking the tool cart 😆
@willpierson5861 I'll look into that. Thanks for the info!
The red hyper tough pry bars look so much better than the black ones they actually look professional 😂
Really nice setup. I have a 4 drawer cart that I have packed to the gills. Literally more tools than most guys have in 2 carts lol. Love seeing a guy using cheap tools. Can't wait for more videos, I do some myself on another channel.
@larrydudgeon2846 Thanks for watching and commenting! I try not to spend on expensive stuff if I don't need to. I've built and repaired plenty of stuff with less lol. Share your other channel, I would love to check it out!
By far the best Tool box 5 drawer setup. Really like the links to all products as i too have a green 5 drawer and like to color match. Great job
@@critiical Thanks for taking the time to watch and comment! It's been through a few configurations over the years, but I think I finally have one I like.
Very nice. Thanks for all the links too. I’m picking up that box and need those organizing trays - looks like they fit perfectly
@jasoncharles6980 they are a perfect fit. Thanks for checking out the video!
Very, very nice setup !!!!!
@@toddhickox4757 Thanks for watching and commenting!
Cool video and sweet box setup. Thanks for the video
@@hoobsgarage Thanks for checking it out!
Keep the videos coming, love the OBS
@mattlyles2419 Thanks for taking the time to watch and comment! I'll be working on more soon. It's time to get my stuff back on the road.
Good video. I picked up a couple of ideas. Good luck with your projects and your channel. I'm a new subscriber.
@77gmcnut Thanks for watching and subscribing! I'm glad to hear you saw something helpful in there.
Send one of those clean Chevys up here to NY. Ours are all rotted!
the 1st shortbed in the video is stipl mu dream truck
@@patrickbledsoe2176 That one is definitely my favorite. It's low and wide, really fun truck.
Vid on the truck @5seconds !!?
subbed! great vid! are you gonna do tours of your other boxes?
@@bafagu2 Thanks! I was planning on doing them as well. I'm in the middle of 3D printing tool holders for them since everything has been moved around.
cup holder should be higher on a taller toolbox to avoid contaminants . thanks for the video .
@RAY44444 If I'm slinging stuff around, I usually move it to the lid for any open container. I keep water bottles nice and low so my old self can slide over and grab it without getting up off the floor lol. Thanks for watching and commenting!
Tool thrift store? I gotta find one
Nice setup, I enjoy tours like these. (But buddy, get a better mic!) I have some of those Hyper Tough prybars, huge fan
@Benzene3686 Thanks for the feedback. I noticed it was a bit off sounding, and I think it was my fault [poor positioning]. The prybars are a great deal!
I really like those ratchet holders, do you 3D print them
@@jazzman452 I found files for these on Thingiverse.com and printed them. They are ok, could definitely be better
@@jazzman452 If you can't print your own, these guys do nice work.
www.toolprintingtechnologies.com/
I see your drill bits are in a Huot case, but what brand are the bits themselves? Im looking for a pretty complete index like thaf myself. Great tour!
@Carterthielftw_ I started with a set from the Yard Store when I was just getting into the aviation industry. Over the years, the bits have been replaced by the places where I worked. I couldn't find a brand on the bits, but here is the setup.
www.yardstore.com/drill-bit-set-combo-fractional-letters-numbers-high-speed
Thanks for watching!
where do you find those ratchet holders
@mavrik9475 Thingiverse.com under modular ratchet holders. There are many different types. If you aren't able to print your own, check out www.toolprintingtechnologies.com
Anyone organizing on the cheap? Casoman Socket Organizer is on crzy sale right now on amazon. Ordered trays for 1/4,3/8,&1/2 SAE & Metric for 14$ total - single listing.
Peg Type like a Jensen socket trays if familiar.
The setup in the vid is nicer for reaching down into. But for my non-production level work - hope these cheapies do the job.
@patricksquires77 I've never tried those, but I do have a lot of Goliath Industrial socket rails. I got them pretty cheap on eBay. They had a bunch of lower priced options that have held up decent.
I think the magnet style like I have can be found for pretty cheap now too. A lot of different brands carry them on Amazon.
Please can you tell me what brand are your socket organizers? Thank you.
@techman7141 The green and black magnetic holders in the top are Ares brand. The others in the top are Ernst twist lock rails. There are links in the video description that will take you straight to them on Amazon 👍
@@Double7-DIY-Garage I'm sorry I saw the links after, But Thank you for letting me know
@@techman7141 No problem, always happy to answer questions
What 3D printer do you use to print?
@@jake7833 I have the Elegoo Neptune 4 Plus. I'm still pretty new at 3D printing, but it's great for toolbox stuff.
The sound isn’t that great for some reason.
@@montestu5502 That was poor mic placement. Noob mistake on my part.