@@umairpk11 Hello What is WP(IO2) and GND. GND is ground or minus, and IO2, the second pin. If you can attach a photo of the system you repaired, mark which pins you shorted. Regards
Disable wifi adapter first, Goto Local Area Network, change ip address: 192.168.1.10 & default gateway: 192.168.1.1 Now holding reset button plug in your router, Open 192.168.1.1 in your browser tab, select original firmware file then click on upload. *when the recovery page shows in the browser you release the reset button.
Great VDO, I bricked my tenda years ago and don't remember the IP address I have set it to (it's not the default ip address) is there anyway to find out what it was? Currently the computer auto config the IP to 169.254... range, any help would be greatly appreciated
@@umairpk11 did that, after renew command, CMD show message along the line cannot config IP, I tried wireshark but couldn't get anything for ARP either From your clip, once you know the static IP, disconnect the power from router, reconnecting the power while holding on to the reset button, once all the light on the router flash, short the 2 legs, is this correct?
@@waqastariq5941 1. Download Tenda firmware file (BIN) from the official website. 2. Format USB drive (FAT32). 3. Copy firmware .bin file to USB drive root directory. Recovery Steps: 1. Power off router. 2. Insert USB drive into the router's USB port. 3. Press and hold the reset button. 4. Power on router. 5. Release the reset button after 10 seconds. 6. Router will automatically detect USB drive and update the firmware.
did this worked please reply 🙏i have also n301 its starting lights are on but not showing wifi name and not connecting to my pc through Ethernet cable its say unidentified network
@@Mohammad-Al-Amin try same process, if not work try 1. Plugin Router & Press Reset Button for 30 seconds. 2. While holding the reset button Plug off the router and plugin again.
Tenda router galat software ke karan brick ho geya aur abhi Ethernet unidentified and network hidden dikha raha hai, connect bhi nehi ho raha hai... Kya karu, pls help
Bhai mene tenda ac7 1200 buy kiya tha iss main disconnect ka issue a raha ha............main jb speedtest krta hun tou download test k bad jese hi upload test ata ha yeh router disconnect ho jata matlab jb uploading hoti ha tou disconnect hota ha 1 minutes ke liye aur yeh setting se reboot bi nhi hota phir iss ko manually reboot krna parta ha................apko problem sumj ayi aur ap kya advise karein gy??
Reset kar k dobara configure karen. Ager phir b problem aati hy tu tenda ki official website sy isi model ka latest firmware download kr k upgrade karen.
Open Network & Sharing Center goto Change adapter settings right click on Local Area Connection double click Internet Protocol Ver 4 then select Obtain an IP and DNS server address automatically. OK.
Also try this method: Disable wifi adapter first, Goto Local Area Network, change ip address: 192.168.1.10 & default gateway: 192.168.1.1 Now holding reset button plug in your router, Open 192.168.1.1 in your browser tab, select original firmware file then click on upload. *when the recovery page shows in the browser you release the reset button.
To update the firmware of your Binatone WR1500N router, follow these steps: Go to the official website of Binatone and search for the firmware download section. Look for the latest firmware version available for your router model and download it to your computer. Connect your computer to your Binatone WR1500N router using an Ethernet cable. Open a web browser and type in the IP address of your router. The default IP address for most Binatone routers is 192.168.1.1. Enter your router's login credentials to access the web interface. Look for the firmware upgrade option in the settings or maintenance section of the web interface. Click on the firmware upgrade option and browse for the firmware file you downloaded earlier. Click on the upgrade button and wait for the firmware upgrade process to complete. Once the upgrade is complete, your router will reboot automatically. It is recommended to backup your current router settings before updating the firmware. Also, make sure not to power off the router during the firmware upgrade process as this can brick the device. Follow the firmware upgrade process carefully and wait for it to complete before attempting to use the router again
Disable wifi adapter first, Goto Local Area Network, change ip address: 192.168.1.10 & default gateway: 192.168.1.1 Now holding reset button plug in your router, Open 192.168.1.1 in your browser tab, select original firmware file then click on upload.
What pins did you shorten VCC and HOLD?
I would like to do the same with the BIOS of the MX25L1606E system in the Tenda AC6 router
/WP(IO2) and GND
25q16bsig chip in this router.
@@umairpk11 Hello
What is WP(IO2) and GND. GND is ground or minus, and IO2, the second pin. If you can attach a photo of the system you repaired, mark which pins you shorted. Regards
/WP(IO2) is the 3rd pin of IC
Datasheet link: www.datasheetmeta.com/search.php?q=25Q16BVSIG
Muhammad eres un crack, muchas gracias por tu tutorial, ya iba a tirar a la basura mi Router Tenda W311r+. Muchas gracias...
Disable wifi adapter first,
Goto Local Area Network, change ip address: 192.168.1.10 & default gateway: 192.168.1.1
Now holding reset button plug in your router,
Open 192.168.1.1 in your browser tab, select original firmware file then click on upload.
*when the recovery page shows in the browser you release the reset button.
Great VDO, I bricked my tenda years ago and don't remember the IP address I have set it to (it's not the default ip address) is there anyway to find out what it was? Currently the computer auto config the IP to 169.254... range, any help would be greatly appreciated
Open CMD, type ipconfig/release press enter, ipconfig/renew press enter
@@umairpk11 did that, after renew command, CMD show message along the line cannot config IP, I tried wireshark but couldn't get anything for ARP either
From your clip, once you know the static IP, disconnect the power from router, reconnecting the power while holding on to the reset button, once all the light on the router flash, short the 2 legs, is this correct?
@@splco.ltd.9400 yes
It really worked !!!!!
Thanks
@@umairpk11 me kr rha hu but ho ni rha
which router? model?
@@umairpk11 same
apka number mil skta ???
Bhai same problem digsol router ka recovery mode par video bhanavo na
digsol router model??
fh456 maib galat firmware install ho gaya . ab router stuck hai sys light per
@@waqastariq5941
1. Download Tenda firmware file (BIN) from the official website.
2. Format USB drive (FAT32).
3. Copy firmware .bin file to USB drive root directory.
Recovery Steps:
1. Power off router.
2. Insert USB drive into the router's USB port.
3. Press and hold the reset button.
4. Power on router.
5. Release the reset button after 10 seconds.
6. Router will automatically detect USB drive and update the firmware.
@@umairpk11 lekin mera router v1.0hai. aus ki file hi nai hai website per
@@waqastariq5941Tenda FH456 (V1.0) Router Firmware 10.1.1.1 drivers.softpedia.com/get/Router-Switch-Access-Point/Tenda/Tenda-FH456-V10-Router-Firmware-10111.shtml
bro ptcl sa modim ka hl nikalo softwer upgrad krte ho lite chili gi
model?
Very good
Thanks
Tenda n301 ka same process rhahega Kay ?
1. Plugin Router & Press Reset Button for 30 seconds.
2. While holding the reset button Plug off the router and plugin again.
did this worked please reply 🙏i have also n301 its starting lights are on but not showing wifi name and not connecting to my pc through Ethernet cable its say unidentified network
@@rawafkarim4469 try to add manual IP or open cmd (command prompt) i.type 'ipconfig/release' press enter, ii.type 'ipconfig/renew' and press enter.
@@umairpk11 brother i have this problem in tenda f3 .. Help me with the process
@@Mohammad-Al-Amin try same process, if not work try 1. Plugin Router & Press Reset Button for 30 seconds.
2. While holding the reset button Plug off the router and plugin again.
Tenda router galat software ke karan brick ho geya aur abhi Ethernet unidentified and network hidden dikha raha hai, connect bhi nehi ho raha hai... Kya karu, pls help
Router model?
@@umairpk11tenda N300
@@jaatscorpion manual ip daal k try kren, 192.168.1.1
Nhi ho rha sir @@umairpk11
Bhai mene tenda ac7 1200 buy kiya tha iss main disconnect ka issue a raha ha............main jb speedtest krta hun tou download test k bad jese hi upload test ata ha yeh router disconnect ho jata matlab jb uploading hoti ha tou disconnect hota ha 1 minutes ke liye aur yeh setting se reboot bi nhi hota phir iss ko manually reboot krna parta ha................apko problem sumj ayi aur ap kya advise karein gy??
Reset kar k dobara configure karen. Ager phir b problem aati hy tu tenda ki official website sy isi model ka latest firmware download kr k upgrade karen.
www.tendacn.com/product/download/AC6.html
bro , need urgent help regarding TENDA N301, unidentified network and on pc's wifi hidden network show ho rha h ,
Open cmd, type ipconfig/release press Enter
ipconfig/renew press Enter.
Or add manual IP address
vai apka video dekhke mene kiya lekin computer pe router ka koi adapter nehi aa rahahe abb kiya karu
Check Lan driver
& connect with the Lan port not Ethernet
@@umairpk11 yes is ok. thanks
Cool
Sir same problam mtlink 850 help me
mtlink?
will this work on tenda f6
Maybe
@@umairpk11 no it doesn't . haha😁
Sam default gateway kdr se ho ga
Open Network & Sharing Center
goto Change adapter settings
right click on Local Area Connection double click Internet Protocol Ver 4
then select Obtain an IP and DNS server address automatically.
OK.
Tenda F6 ufo model proses
tenda w268r funcionara?
try same method...
Tenda n301 router ase recovery mai nhi jaa raha bro help me plz
Try the same procedure if not working using the ic programmer tool.
Also try this method: Disable wifi adapter first,
Goto Local Area Network, change ip address: 192.168.1.10 & default gateway: 192.168.1.1
Now holding reset button plug in your router,
Open 192.168.1.1 in your browser tab, select original firmware file then click on upload.
*when the recovery page shows in the browser you release the reset button.
Sir binatone 1500n ka btao sir firmware kaise hongya
To update the firmware of your Binatone WR1500N router, follow these steps:
Go to the official website of Binatone and search for the firmware download section.
Look for the latest firmware version available for your router model and download it to your computer.
Connect your computer to your Binatone WR1500N router using an Ethernet cable.
Open a web browser and type in the IP address of your router. The default IP address for most Binatone routers is 192.168.1.1.
Enter your router's login credentials to access the web interface.
Look for the firmware upgrade option in the settings or maintenance section of the web interface.
Click on the firmware upgrade option and browse for the firmware file you downloaded earlier.
Click on the upgrade button and wait for the firmware upgrade process to complete.
Once the upgrade is complete, your router will reboot automatically.
It is recommended to backup your current router settings before updating the firmware. Also, make sure not to power off the router during the firmware upgrade process as this can brick the device. Follow the firmware upgrade process carefully and wait for it to complete before attempting to use the router again
Ic pin number kiya hai
/WP(IO2) and GND
/WP(IO2) is the 3rd pin of IC
Bhai plz tenda f6 ka batao
Try the same, if it does not work, Program bios file to ic with programmer.
tenda ac5 please
Disable wifi adapter first,
Goto Local Area Network, change ip address: 192.168.1.10 & default gateway: 192.168.1.1
Now holding reset button plug in your router,
Open 192.168.1.1 in your browser tab, select original firmware file then click on upload.
*when the recovery page shows in the browser you release the reset button.
@@umairpk11how long it’s take to reset??
@@mohammad.rana.sheikh maybe 30sec to one minute, if not work try plug off and replug in with the holding reset button.
Thnx bro
Welcome bro
Hlw
D-Link work
which model?