Hi Chantelle, if either the hotplate has failed or the switch has broken would result in the hotplate not working, you can test the hotplate with a multimeter and check the switch but make sure the cooker is disconnected first.
good day, what could be wrong if 2 of my 4 plates are not going on, both the plates are on the right. I turn my knobs and no light goes on. for both plates(Note they share one light). So in short the one half is off and not working.
Most electric cookers have a terminal block connector where the cable enters the unit. This often has metal 'links' that can burn if they were not tightened correctly. Check for signs of damage and replace if required. For more information see another video: ua-cam.com/video/F4zC4GYWSwk/v-deo.html
can you show how to connect 3 phase 440 volts rotary switch to low, medium, and high position electrical burner , using three electrical elements[ three elements 3 starting and 3 end terminal of elements] THANKS REPLY
Hello Spilt water after cooking all over plates Cooker turns off at main electric box how do i get rid of water. My cooker is badly fitted into the wall and I don’t have access for the rear can I send you Pictures??
Hi Hugh, leave the hob off and allow enough time for the components to dry out, I would normally suggest you test the appliance with a meggar before switching back on. you can take it apart but try this first.
Hi Cindy, It could be the hot plate or the control. Disconnect the power and check the control for signs of grease, burning or black marks as this may cause the problem. See another video: ua-cam.com/video/1jpfYgotUC0/v-deo.html
actually all electric cookers are hard wired in plus i have that exact cooker in white and its hard wired in also 1 cooking plate on that is 2000 watts so 2000 watts plus 6000 watts equals 8000 watts plus a 13 amp fuse rating is only 3000 watts which is 3 kilowatts.
Hi Chris, the model of this cooker is an Indesit K3E1. If you are trying to confirm your model there should be a small label on the oven cavity surround that you can see when the door is opened. For more information finding your model detail see our website at: www.espares.co.uk/findingmodelnumbers
Hi Sami, many elements can glow red when on full but to control the heat they should cycle on and off, If the other rings on half heat turn on and off for 50% of the time but the ring in question does not. The problem is likely to be the control (regulator) See these other videos: ua-cam.com/video/F4zC4GYWSwk/v-deo.html and ua-cam.com/video/BdVtk3ZH-Hc/v-deo.html
Thanks that looks like its going to save me a load of time
wow this guy is fantastic good teacher thank you my friend you are my hero
Thanks for the great feedback Answar, remember to 'like’ the video if you enjoyed it or it helped.👍
Hi There.. what cold be the problem ? i have replace the plates with the new one but heat is too low please assist .
Muchas gracias. Me sirvio mucho la explicación.
Thanks!!!
Is there a video detailing how to do this on a built in one?
How would I know which wattage plate replacement to buy? Thanks
Very helpful
Hi Craig. We're glad to hear this video helped you fix your appliance.Remember to give this video a thumbs up if you enjoyed it.
Should it smell like burnt plastics after you done
very nice but i just want to know why does a plate stop working what goes wrong ? it just stop working? no reason?
Hi Chantelle, if either the hotplate has failed or the switch has broken would result in the hotplate not working, you can test the hotplate with a multimeter and check the switch but make sure the cooker is disconnected first.
good day, what could be wrong if 2 of my 4 plates are not going on, both the plates are on the right. I turn my knobs and no light goes on. for both plates(Note they share one light). So in short the one half is off and not working.
Most electric cookers have a terminal block connector where the cable enters the unit. This often has metal 'links' that can burn if they were not tightened correctly. Check for signs of damage and replace if required. For more information see another video:
ua-cam.com/video/F4zC4GYWSwk/v-deo.html
:-)
can you show how to connect 3 phase 440 volts rotary switch to low, medium, and high position electrical burner , using three electrical elements[ three elements 3 starting and 3 end terminal of elements] THANKS
REPLY
Sorry we only have videos for single phase 'domestic' appliances and do not cover three phase as this is commercial/industrial equipment.
I was checking a video about how to replace or fix wiring of Two plate stove on the burners but i just cant find one.. Any help
Hi Sharlotte QSP, unfortunately we don't have a video on a 2 plate stove.
@@eSpares i keep blowing circuit braker i got all the hobs disconnected . Oven an grill ok any ideas pls tks
Hello
Spilt water after cooking all over plates
Cooker turns off at main electric box how do i get rid of water. My cooker is badly fitted into the wall and I don’t have access for the rear can I send you
Pictures??
Hi Hugh, leave the hob off and allow enough time for the components to dry out, I would normally suggest you test the appliance with a meggar before switching back on. you can take it apart but try this first.
Please I was wondering can an electric griddle pan be replaced as well?
Most parts are replaceable on most appliances, what is your model number?.
I have problem with one hot plate when using my fuse box cuts out could it be element?
Hi Cindy, It could be the hot plate or the control. Disconnect the power and check the control for signs of grease, burning or black marks as this may cause the problem. See another video: ua-cam.com/video/1jpfYgotUC0/v-deo.html
actually all electric cookers are hard wired in plus i have that exact cooker in white and its hard wired in also 1 cooking plate on that is 2000 watts so 2000 watts plus 6000 watts equals 8000 watts plus a 13 amp fuse rating is only 3000 watts which is 3 kilowatts.
can you replace the the top with induction type?
+jay sharr Induction rings cannot be fitted to a standard electric ring controller so cannot be fitted to any cooker that is not designed for them.
Hello, what is the model of that oven?
Hi Chris, the model of this cooker is an Indesit K3E1. If you are trying to confirm your model there should be a small label on the oven cavity surround that you can see when the door is opened. For more information finding your model detail see our website at: www.espares.co.uk/findingmodelnumbers
hi the plate turns red after a while everytime I turn it on is this normal ?
Hi Sami, many elements can glow red when on full but to control the heat they should cycle on and off, If the other rings on half heat turn on and off for 50% of the time but the ring in question does not. The problem is likely to be the control (regulator) See these other videos:
ua-cam.com/video/F4zC4GYWSwk/v-deo.html and
ua-cam.com/video/BdVtk3ZH-Hc/v-deo.html
thanks
thanks dear
Thanks for the comment Mohamed. Remember to like and subscribe if you find this video helpful.
you sond Matt
Is there a video detailing how to do this on a built in one?