Tuxing TXES031 300bar pcp compressor cooper serpentine mod pumpung FX Maverick faster
Вставка
- Опубліковано 26 вер 2024
- Tuxing TXES031 300bar pcp compressor with cooper serpentine mod pumping FX Maverick with 400cc from 140 to 260 bar after the mod for 1:50 and max temp of the serpentine is 25C not 82C like with the original pipe between stage 1 and 2. With this mod the air from stage 1 is much colder when go to stage 2 and this reduce the time for pumping,,reduce the condensations ,reduce also the teperature of the head and extend the life of the compressor. The pipe is cooper,diameter 6mm, ticknes 1mm, 12 windings with diameter 40mm. Only the first 4 windings on bottom is hot,the pipe on top is super cold.
An interstage cooler is one of the most important mods for these types of pumps. BUT it does not reduce the total amount of condensation. That is independent from where the heat is drawn out. All air ends at ambient temp. That defines the amount of water at the end. The air comes in with the amount of water that it has. Cold air is good. The difference drops out.
Тоже думал о том, что нужно подавать в компрессор воздух температурой ниже точки конденсации, на пример переохлаждая его холодильной установкой, как бы из морозильной камеры, но это сложно и дорого, хотя , скорее всего уберёт всю или почти всю влагу...
@@alexmackey9922 You can use water vapor pressure tables to see that.
When you compress directly to 300 bars, you need to cool ambient air down to -80°C to not get condensation at 300 bars/20°C. Not very practical.
If you precompress to 10 bars and cool then, -22°C is enough to crash out enough water to not have condensation at 300bars/20°C. At 15 bars it is -19°C. More viable, but still a hassle.
If you use a high pressure condenser inside a freezer, it will probably work well at higher pressures. Still the first 100 bars tend to carry too much moisture into the bottle, if not run over molecular sieves.
I like to dry the air at that intermediate pressure level. Cool down to ambient, drain the water and then run the rest through quite large molecular sieve beds. 2'' stainless steel pipes with endcap fittings filled with sieves. These can easily be regenerated in a kitchen oven at 250°C, or with a vacuum pump and milder heat. Whatever is more practical at the moment.
Buen video compañero like parati y nuevo suscriptor 🤝
Is it plug and play? And what's the length of the copper pipe?
Not sure what that first stage pressure on your compressor is but ATSM 280 refrigerant line in 1/4 with an .030 wall (close to your 6mm with 1mm wall) is rate for 1200psi. While big box stores sell K,L, and ACR copper that are rated for around 900PSI. For a 4500psi compressor that might be sketchy without knowing the first stage pressure.
First stage outputs around 150psi max I think
Knowing would be better, sure. But I think there is PLENTY of headspace to 900 and even more to 1200psi.
1mm wall thickness would be a 0.040 wall. Quite a bit more even than your 1200psi pipe.
I have absolutely no safety concern here.
ótimo equipamento meu amigo um sonho pra quem tem PCP
If u want to have answer, You must write on english. I have NO IDEA waht u say hahahah 😄
@@PETRAKOV1 He said ( Great equipment my friend a dream for anyone with pcp)
@@PETRAKOV1 Here in Brazil there are few that use a compressor to recharge the pcp, most use a manual pump to recharge
@@shotdown4167 So big airtank wich need to be fill to 300bar with hand pump is suicide 😁 This compressor is not so expencive. From aliexpress cost 200 euro with delivery and pum 580cc airtank from 150 bar to 300bar for 2 min 😁 The compressot work perfect also is wery simple bild and cheep to be repair if stop for some reason.
@@PETRAKOV1
Here there are few who are able to buy, but thank God I bought mine now it's just joy 🙏
Que tipo de óleo você esta usando? Subiu óleo para o cabeçote?
If u want to have answer, You must write on english. I have NO IDEA waht u say hahahah 😄
1. Does FX like wet air?
2. Can the copper pipe withstand the pressure?
The copper pipe in in the interstage section. It does not see 300 bar. Interstage pressure is much lower. Let's say 20 bar. Copper pipe can hold that easily.
People don't understand that when they fill their guns this way, they get water in their tank. And when their guns break, they don't understand that it may be from water. So you don't get a reliable answer to this.
I don't fill anything without a fill throttle and fill with high pressure ambient temperature air. So all condensate is out.
Você teve algum problema com óleo no filtro, qual óleo você tá usando?
If u want to have answer, You must write on english. I have NO IDEA waht u say hahahah 😄
Здравствуйте,здорово,змеевик от самогонного аппарпта)))))))
English,please.
@@PETRAKOV1 Вась,не гони)
This truly works. Thanks for the idea. I used about 1.2 meters length of 6mm diameter copper tube and bent it around (not coiled) so that I can fit it within the existing cabinet. Much faster filling of my home-made PCP air rifle. ua-cam.com/video/KOyCoE68mIU/v-deo.html
Great thanks for sharing this video can i ask you are you recommend this compressor model ?
полное фуфло,пользуюсь больше года ,ремонтировал 20 раз уже
Можели да се ползва антифриз вместо вода?
Слага се дестилирана вода ,примерно 8-10 литра и в нея се слага 200 грама хубав антифриз за БМВ например,защото бмвтата са с алуминиеви блокове и глави. Главата на компресора е алуминиева и чист антифирз ще я прецака.Добавянето на малко антифриз предпазва от корозия и замръзване.
@@PETRAKOV1English please ;)
Hi friend! Where did you buy this serpentine? Is there some specific name for this part? Thank you!
I made it. Its very easy to make a cooper pipe on coil. they simply wind the pipe around the handle of a shovel
It is a piece of pipe wound around something round.
За какво служи малкия бутон до дисплея за температурата забелязах на моя че спира през 10тина минути и не иска да тръгне отново докато не го натисна имам чувството че чисти някакво напрежение от кондензатора или просто моя кондензатор е за смяна
What is it connected to on the inside? My yong heng clone does not have this button.
Copper tube 6mm, is this the inner or outer diameter?
Outsite 6mm
hello from brazil. why did you change the tube? does it improve cooling? thanks
This serpentune keep lower temperatureof the air wich going from stage 1 to stage 2.This inprove the time for pupping,aslo save the compressor
Interstage cooling. The heat drawn out there does not get amplified during HP compression. You can reduce peak temperature at the high pressure side significantly.
Тръбичката от тези за АГУ ли е или друг вид?
Google : "медна тръба ф6х1мм цена" Важното е да е 1мм дебелина за да държи повече налягане. Мисля,че на ф6х1мм и даваха към 160бара максимално налягане. За първа степен на компресора е ОК. Там налягането е доста по ниско.
The copper pipe inside 6 mm ?
OD. Inside 4