I have the exact same problem, unfortunately, your picture on the part when you have soldered the antenna quite blurry. I cannot see to where did you solder the tip of the metal. I checked mine and did not see where should I solder it except white strip on the board. Do I just solder it to the board (that white strip)?
it's very simple, a weld should be made between the pin on the motherboard and the new antenna plug, and then you have to weld the external plug well so that it does mass, that's all ... if you need, ask
Went to turn on my Panasonic 39" LED TV and spotted a little pool of water on the floor beneath it.....after a night of heavy rain, water had trickled down inside the exterior holed aerial cable and straight into the tuner part before dripping out past the speaker! When turned on there is a NO SIGNAL message! Could it be that the aerial connection/tuner circuitry affected just need a gentle rub down and a bit of heat....can you suggest a cheap DIY fix for such a water-ingress problem...is it likely that electronic parts near the Tuner are damaged....your video gives me, well.......hope!? Any advice would be welcome!
hi, the best solution for your problem is a ispophilene alcholl and a good brush, the trick to solve problems caused by water, is to remove the boards as quickly as possible and avoid the oxide
Lo q necesito saber es donde va el positivo si el huequito del positivo no tiene soldadura quedo sin marca alguna esta sin nada y no c de donde lo puedo soladar xfa me puede ayudar con un video o tendre q comprar la tarjeta .gracias
Mine broke off just like that one. My fire wood ring is next to the TV and I loaded too much wood to one side causing the ring to roll. Result was it rolled on the cable yanking it right out of the tuner. Tried to repair it just like you did but must not be soldered properly to the board because it still don't work. Didn't make it any easier my eyes strain trying to see what I'm doing was hoping for better results.
@@SappohSamaWorkshop I gave it another try about 6 months ago and it's fixed now. I had to dig deeper and found a connection on the board that was broken also do I bridged it with some wire and like magic it was fixed.
si certo, se guardi dentro "lo scatolotto" dell'antenna, vedrai un piccolo puntino metallico dove prima c'era attaccata la connessione dell'antenna, và riattaccata esattamente li con dello stagno, a volte non è facile, in quanto il buco per far passare il saldatore è piccolo, e a volte và allargato con delle pinze e poi risaldato bene con lo stagno
the work works as shown by the video, and then it is not a welding course, it just plain shows a technique ... If you are that good at soldering, take your own videos and show others how good you are
I just tried this on our tv and to my amazement is worked! Thanks a lot.
You're a champion mate! I just fixed mine. Thanks👍
your'e welcome ;) TNX
I have the exact same problem, unfortunately, your picture on the part when you have soldered the antenna quite blurry. I cannot see to where did you solder the tip of the metal. I checked mine and did not see where should I solder it except white strip on the board. Do I just solder it to the board (that white strip)?
it's very simple, a weld should be made between the pin on the motherboard and the new antenna plug, and then you have to weld the external plug well so that it does mass, that's all ...
if you need, ask
Went to turn on my Panasonic 39" LED TV and spotted a little pool of water on the floor beneath it.....after a night of heavy rain, water had trickled down inside the exterior holed aerial cable and straight into the tuner part before dripping out past the speaker! When turned on there is a NO SIGNAL message!
Could it be that the aerial connection/tuner circuitry affected just need a gentle rub down and a bit of heat....can you suggest a cheap DIY fix for such a water-ingress problem...is it likely that electronic parts near the Tuner are damaged....your video gives me, well.......hope!? Any advice would be welcome!
hi, the best solution for your problem is a ispophilene alcholl and a good brush, the trick to solve problems caused by water, is to remove the boards as quickly as possible and avoid the oxide
You need to create a drip loop outside on your aerial cable or it will happen again 😪
Lo q necesito saber es donde va el positivo si el huequito del positivo no tiene soldadura quedo sin marca alguna esta sin nada y no c de donde lo puedo soladar xfa me puede ayudar con un video o tendre q comprar la tarjeta .gracias
so we need soldering with motherboard insides between the pin ? need to be touch with pin or not ? thanks
you only need to touch the pin in the motherboard, and then solder the antenna at the antenna box
Cheers helped me out.
your'e welcome ;)
Mine broke off just like that one. My fire wood ring is next to the TV and I loaded too much wood to one side causing the ring to roll. Result was it rolled on the cable yanking it right out of the tuner. Tried to repair it just like you did but must not be soldered properly to the board because it still don't work. Didn't make it any easier my eyes strain trying to see what I'm doing was hoping for better results.
i now it's not easy, but it's not impossible...
@@SappohSamaWorkshop I gave it another try about 6 months ago and it's fixed now. I had to dig deeper and found a connection on the board that was broken also do I bridged it with some wire and like magic it was fixed.
@@stoneyswolf i'm happy to hear ;)
big up!!!
where can I buy one of those antennas? Have the same problem.
I recover them from old broken motherboards, they are all compatible ...
That's expensive?
It all depends on the technician you bring it to ...
to give you an example I take from 20 to 30 euros (like 25 35 dollars)
where I can find this type of antenna connector any website links ..thanks
I have no luck finding one either, all the large component stores do not have anything like it, does anyone know he name of he component?
I recover them from old broken motherboards, they are all compatible ...
@@robbroadster I recover them from old broken motherboards, they are all compatible ...
Thanks
tnx u too bro, welcome to the channel!!!!
Esiste un punto esatto in cui va saldata la linguetta del connettore?
si certo, se guardi dentro "lo scatolotto" dell'antenna, vedrai un piccolo puntino metallico dove prima c'era attaccata la connessione dell'antenna, và riattaccata esattamente li con dello stagno, a volte non è facile, in quanto il buco per far passare il saldatore è piccolo, e a volte và allargato con delle pinze e poi risaldato bene con lo stagno
Wat if ther is just a Lil hole on motherboard
u can post a photo?
ma lo scopo di questo video quale era????
Le travail n'est pas soigné. Soudure des apprentis.
the work works as shown by the video, and then it is not a welding course, it just plain shows a technique ... If you are that good at soldering, take your own videos and show others how good you are
I'll
?
Would...HELP If Big Fingers....Wasn't Blocking My VIEW...!!!
yes, tell me my friend, how is your problem?