Not sure if anyone has mentioned this, but version 1.7.1 is required. I tried using an older version (1.6.x) and noticed different behavior. Initially, I thought there was an issue with my soldering, but it turned out the problem was due to using the outdated version. Note: Thanks a lot for the idea! My build is almost the same, and I'm very happy with it
I connected my c plus 2 stick to the c1101 with jumpers, it recognizes the module, but the spectrum doesn't work for example, and it doesn't even send signals
Hi thanks for this great video!i noticed that you connect with cable to the cardputer all the pins,while on bruce repo schematics of the cc1101 connection with sd sniffer it's needed to connect only g1 an g2,could you plese share the schematics you followed? Thanks!
the schematics in the bruce repo is correct, the gnd and vcc on grove port in the video isnt connected to the female pins for cc1101, only the scl and sda is wired to the pins. he just doing it for convenience so he dont need to keep swapping cable for the other modules with grove port.
It's the same schematics from bruce repo. The only difference is that I didn't connect the CC1101 directly, instead I used connectors to make it easier to plug it and change between modules
Sir can I tell me the name of the board that has grove I was checking in online i didn't find can u tell the name of the board blue color used to connect grove port
You can't, cardputer does not have enough GPIO pins for that. You can only do this with cables in the StickC Plus2. Check Pirata's video in the description
I believe I saw a scheme to solder the wires directly to the cardputer circuit. It has its difficulties, but it would skip the sd sniffer step. I think I saw this on Bruce's github.@@R3CkTech
Not sure if anyone has mentioned this, but version 1.7.1 is required. I tried using an older version (1.6.x) and noticed different behavior. Initially, I thought there was an issue with my soldering, but it turned out the problem was due to using the outdated version. Note: Thanks a lot for the idea! My build is almost the same, and I'm very happy with it
I connected my c plus 2 stick to the c1101 with jumpers, it recognizes the module, but the spectrum doesn't work for example, and it doesn't even send signals
I get defected modules all the time
Sometimes it’s because the pins are not soldered all the way due to the assembly line process
Hello i just bought RF433T and R modules, but dont know where to use them. Is there a repo with only 433mhz signals?
btw, is there spectrum with rf433r module? I'm using cardputer and it freezes every time i click spectrum
Muito bom o vídeo!!
Hi thanks for this great video!i noticed that you connect with cable to the cardputer all the pins,while on bruce repo schematics of the cc1101 connection with sd sniffer it's needed to connect only g1 an g2,could you plese share the schematics you followed?
Thanks!
the schematics in the bruce repo is correct, the gnd and vcc on grove port in the video isnt connected to the female pins for cc1101, only the scl and sda is wired to the pins.
he just doing it for convenience so he dont need to keep swapping cable for the other modules with grove port.
It's the same schematics from bruce repo. The only difference is that I didn't connect the CC1101 directly, instead I used connectors to make it easier to plug it and change between modules
Sir can I tell me the name of the board that has grove I was checking in online i didn't find can u tell the name of the board blue color used to connect grove port
you have to make it yourself. Buy the connectors and solder everything
Which modules are you using? I think you have 5 and how you connect all of them in one. It looks really good and slim btw
Do you mean the ones in the back of the cardputer? If so it’s an RFID2, RF433R, RF433T, GPS and IR
hi, i am going to buy m5stickc plus 2 but what modules/cards do you suggest me to buy?(And can u describe what can i use them for)
@ it depends on what you want to achieve. Bruce supports IR, RF, RFID, GPS… First you need to define what your goals are
@@R3CkTech i got a cc1101 and a 433mzh Lora module
How can I solder the wires to the proto? Do you have a template?
ok ok I'm stupid it's the same scheme as without proto lol
Can i use both nrf24 and cc1101 on the sd sniffer at the same time?
@@sufiasarowar4240 Nope, because it does not have enough gpio pins. And I can’t imagine a scenario where you would need both at the same time.
how you attach m5 modules to cardputer ? with something custom 3d printed or ?
@@nikolaydachev9691 they’re attached using some Lego technic pins
It is possivel you make a 3d print case for the cardputer module? Thanks. Great job
Yes, it is. But I don't have a 3D printer
@ ok, when you have stl files, ia possível you put here?
@ Or if you already have the stl files put in thinkverge with the reference to cardputer mod cc1101 case
do you have the links for the things that are used in this video pls?
@@xampu7892 we have links for every module and every part on our discord server. Join us there discord.gg/bruce-firmware-1264994142769909854
what is the way that i can do it without the sd sniffer ( its not available ) , the cables way is batter for me but how
You can't, cardputer does not have enough GPIO pins for that. You can only do this with cables in the StickC Plus2. Check Pirata's video in the description
I believe I saw a scheme to solder the wires directly to the cardputer circuit. It has its difficulties, but it would skip the sd sniffer step. I think I saw this on Bruce's github.@@R3CkTech
Could you please provide schematics for connections or something?
Check out Bruce’s repository and wiki page
Alright thanks what do you think about nrf24? Which of those 2 is better in your opinion? @R3CkTech
i broke my stick c plus 2
trying to modify the case
@@saski-v7h 🤷♂️
@@R3CkTech yeah i know lol, i will make my own flipper with an esp wroom
cus just cus i need a prankster device