Це відео не доступне.
Перепрошуємо.
Making ESP32 projects smaller😱🤩 | How to program ESP32 Chip using ESP32 Board
Вставка
- Опубліковано 6 сер 2024
- This video will guide you with programming ESP32 chip using ESP32 development board
To try out free trial version of Altium, click here - www.altium.com/yt/techiesms
You can support me🙏🏻 and also get benefitted on Patreon :- / techiesms
Subscribe now💪🏻 to watch some amazing videos coming up soon.
bit.ly/techiesms_youtube
_________________________________________________________________
👨🏻💻 Purchase links 👨🏻💻
Esp32 chip - www.sunrom.com/p/esp32-esp-wr...
Breakout PCB - www.sunrom.com/p/breakout-pcb...
_________________________________________________________________
Now you can get free PCB with every order of techiesms T-shirt or techiesms pocket notebook.
You can buy the merchandise from here,
techiesms.com/merchandise/
_________________________________________________________________
👀 You may Like these videos 👀
Smallest Home Automation project using ESP32 module - • Smallest 🔥🔥 Home Autom...
_________________________________________________________________
Buy the components from your projects 💡🔌
ESP32 Dev board - amzn.to/3jiwCD6
ESP32 Module - amzn.to/3g5CKh5
NodeMCU - amzn.to/2wbzNrZ
Raspberry Pi 4b - amzn.to/3phsKFN
Raspberry Pi pico - amzn.to/2RgeSyW
Arduino MEGA - amzn.to/3vMEkLw
TTGO TCALL module - amzn.to/2SQG6wH
Visit my Amazon Storefront for purchasing any components you need for this project or any other project :-
bit.ly/techiesms-Amazon-Store
_________________________________________________________________
🎥 🎙 My Video Gear 🎙🎥
Camera - Canon 750d
Lens - 50mm f/1.8 STM Lens (amzn.to/32gqnsi), 24mm f/2.6
Key Light - Godox SL60W (amzn.to/3522mHe)
Fill Light/Back Light - Osaka Lightning Setup (amzn.to/2I5cdDi)
Tripod - amzn.to/3uNhC4H
Microphone - Samson Meteor (amzn.to/32jfVAt)
Editing - Final Cut Pro X on MacBook Pro ( amzn.to/3vHcSyJ )
_________________________________________________________________
Subscribe Now :- bit.ly/techiesms_youtube
Facebook :- / techiesms
Twitter :- / imtechiesms
Instagram :- / techiesms
Website :- www.techiesms.com
WhatsApp number :- +91 82000 79034
You can support me and also get benefitted on Patreon :- / techiesms
_________________________________________________________________
techiesms
explore | learn | share
I was looking into the esp32 and saw the smaller boards- I could not find any resources explaining anything but you- so thank you much🙏😊
Excellent job man. It seems all your videos are exactly on the dot for what I am looking for. I already developed some project at home based on your mesh video, and now this will save me lots of space
Actually, the programming device part does not work for all ESP32 board models. So the error "Failed to connect to ESP32: Timed out waiting for packet header" appears, and the solution will not to be add capacitor etc. A solution for this is to use other development boards that have different serial converters, for example: ESP8266, ARDUINO DUE that WORKS FOR THIS PURPOSE. The only difference is that, on the Arduino board we take the reset for GND. Apparently there are two types of serial converters in ESP boards, some of them use the chip that has the CH340 driver that WORKS for it PERFECTLY, and others use CP210x driver that works with the esp8266 for this purpose. Some tests that I performed that do not work are: Arduino UNO model DIP and Arduino Mega. All tests were performed on the W10. I hope to help someone avoid the same headache that I had with this problem kkk
Thank you Sir very kind of you
Hey I have CH340 TTL but I'm also facing this issue, so what can i do buddy
So is better use FTDI module right?
It works like a charm! Thanks, great video!
thank you so much for this, u got urself a new subscriber!
Excellent project !!!
Really really I like it.
It was great, it worked for me. I also used a switch for the boot button so that it doesn't need to be held every time
thanks a lot. this video helped alot
I like your style and way of guiding
I must find my ESP32 Dev board. For I have an important project to make. Thank you for showing the way.
Thanks for sharing, nicely done
Great video! Super interesting, so glad I was recommended
Explore our channel
You’ll get so many more interesting videos here
Enjoy
Creative video, thanks :)
Really interesting!!!
Dude, love the content! Good energy and enthusiasm to keep my ADHD attention and even learned some stuff. At the moment,I am one step deeper, I am working directly with the ESP32-C3 chip and not the chipset. It is impossible to find good content on a minimal circuit for the ESP32-C3 chip (not module). Perhaps a good idea for your next video :)
Super Energetic video.... New idea every Sunday. Great 💙👍💙
Just keep supporting keep sharing and I’ll keep innovating 😇
Nice tutorial, thank you. BTW there is also smaller esp32 dev board on he market, it's called wemos esp32, the size of the board is the same as wemos mini, and it's also compatible with all wemos shield available.
❤️❤️❤️ thank you very much
Great video
Which resistance are you using in this video for ESP 32 breakout board
The quality of your videos had greatly improved.....
Nice and useful video as always...
👍👍👍👍👍❤️🔥
Thank you so much
And
Glad to see that you are noticing the difference and loving it 🥰
Wa Kya entry Mari hai bhai.....cha gye
It was easy, so I clicked the Like button !!
Completely new and amezing concept.
Please make a new video for making the break out pcb in our own.
Is there any way to check if a PCB would work right before ordering it?
3-4 days back I ordered the All in one home automation project. Please, help me when it will be delivered?
What is the battery used for esp32?
Which battery is more efficient ?
Wow! That solder helping hand is really awesome! @2:58
Yeah… 😇
Really interesting thanks! I would be interested to see how to design a PCB containing the ESP32 chip and USB programming interface onto a single PCB, if designing a PCB. It's so cheap to get JLCPCB to manufacture boards with SMD components (including the ESP32-VROOM chip) and I am looking at this for shrinking down my next project.
Wouldn't that be a ESP32-C3-DEVKIT? Schematics are open source
just get devkit ref design ^^
Whatever u think,u can built by learning from this channel....thank u sir for giving such a good creative knowledge....
A huge compliment for me 🙌🏻🙌🏻🙌🏻🙌🏻🙌🏻
Thank you so much 😇
Greeat Video !! Kudos , I have one question Can we directly connect the ESP32 SOC with the ESP32-dev board and program it , without the use of breakout board ,if not why ? my final product needs to be very miniaturized.
How can i USE "HSPI" instead of "VSPI" in ESP32-wrover-b (Which is mounted on TTGO-T-CALL with SIM800L). I want to left "VSPI" for GSM communication.
Subbed! Even sped up your English is excellent from a US Speaker. Looking forward to program my esp32. Any reason you used a soldering iron instead of an oven or hot air gun?
Schematic diagram please, On how that two button is connected
Are you an engineer or an actor ? Your enthusiasm is contagious !
I’m just a maker who is passionate about his work.
And hence my energy resonates with the people who are also passionate enough about this field
If he is not engineer, what is your plan?
And if he is not actor, what is your plan?
@@pareshmhatre4019 techiesms make entrepreneurs 💞🇮🇳😍
@@gsvasanth9077 well said
he is 2 in 1, in indian language it is called Dogla😆
Hi Sachin, you always comes with new concept and feature. I like your all concepts and ideas.
One Request...Can you please make more videos using esp32 module?
Hey, I'm working on a project which uses a battery backup, i saw you used a 250mA 3.7v battery with what i can think is a tp4056 module. I have been studying the sheet of the module and came across the fact that it needs different Rprog (R3 resistor) for different battery current levels.
Did you change yours in any other way as the one which comes with the module is for 1000mA battery
do tell me if your project works fine even though?
Can I read the data inside the board after I program it, for reverse engineering
I think if we want to make my project commercially then we can use this esp32 chip rather than using the development board. It is small in sizs and fits perfectly. Can we use it for commercial selling products??
Can do this with the esp8266 nodemcu and i don't have a pcb what is the diagram?
I dont have any option in stead of ft232 and how do ı use ft232 for programming the esp32?
Excellent! The most important thing I got out of this video is the need for the 2 resistors on those 4 pads. There was nothing in the package to suggest what goes there (I thought the chip had its own pull-up and pull-down where needed). I have an FTDI breakout, but even though the IOs are 3.3V, it's VCC out is 5V, so I'm using the 3.3V power from the dev board. I don't have it programming yet, though, because I don't have the resistors. Maybe I can find out where those resistor pads go and use "real" resistors that I can actually see and handle!
Without any investigation, I presume those 2 pull-up resistors are for the push buttonts.
@@Glanmire3 On my sample of ONE, that was the case. Without the pull-ups, touching, or just getting my finger near the reset button, would cause the module to continuously reset. Sometimes it would not do anything. Adding a single 10k pull-up on the Reset line cured that behavior. It seems to be working fine, even though I did not use a PU on the GPIO 0 line
do you know how much time it takes for a code that is uploaded to repeat itself. I know it is small but if you have a value please help.
Can i make prototype project which I tried on esp32 dev board using this chip?... Without any external vtg regulating? Only push buttons n pull up resistors
Which resister is used
Greetings from México! 🤩
Love from India 😇
Hello. Thank you so much for the great video. I intend to use ESP32-C3-WROOM-02-H4 chip, so can I use ESP32 Board to program it like your video ?
Bro is it not possible to solder wires directly to the chip TX-RX-VCC and GND pins and direct try to program it
why do we short the enable pin to gnd
Hold this chip one at a time to run the program ..?
Can you do a project on nodemcu with pulse sensor?
Hello sir. Hope you are well and safe. Please can you make a video on the "sipeed Maixduino kit"? It has Esp32 chip along with the RISC V K210 processor. There isn't sufficient reviews and application on UA-cam here. Really appreciate your work. Thank you, lots of respect.
Please Friend, I recently purchased ESP8266. Unfortunately the device driver could not install automatically with my version of window 7. After several attempts, I managed to install the driver from sparkfun. I have installed the esp8266 in my Arduino ide library. The problem now is, I am unable to upload a simple code inside the node MCU device. I always get error, "port can't be opened, access denied". If I manage to open serial monitor on code view, I get the following error "port 4 busy" what do I do please?
Under my computer device manager, esp8266 is installed as com port 4. If I switch USB port for the node Mcu, the com port will change to com port 17. I have no other device with com port except the esp8266.
I shrunk the quantum computer down to a grain of dust but I sneezed and it when somewhere. Guess miniaturization has its limits.
Any idea how to unlock a door with the fingerprint scanner on a phone
Nic 😶👍
6:06 which battery you have used there? And can please share the link to that video
Is it wotk eap32 wrover b module.
whats the difference between esp wroom32 and wroom32D
is this chip doesn't require bootloder and all?
i have designed and developed own customize ESP32-S3- board. but i can't able to upload program. pls help me
Can we flash firmware by this method?
Sir can we program it with ttl program
nice...
Tx pin is an output pin. The Tx pins of both chips may have different outputs at the same time. Will this damage the chips? Does it corrupt the communication with the computer?
Probably not, because the chip on the dev board is disabled by grounding the EN pin.
Nice video thanks
😇😇
@@techiesms can we also programme esp 8266 chip like this?
How can I get the components
how to upload code in esp32 using a arduino uno. I tried myself but the code is not uploading.
Hi, thanks for the great videos you've produced. I'm just wondering if you can consider making a video for programming MQTT to wemos D1 mini using Arduino platform with PubSubClient library or any other library which you find more stable. I would like to subscribe/publish to Mosquito broker in home assistant. I personal find that using Arduino with MQTT provide the most flexible way to introduce automation into home assistant because many people have the basic knowledge of programming Arduino in basic level. The only missing link is integration to home assistant. ESPhome is also flexible but is a bit difficult to pick up due to lack of sharing material in the community. Tasmota is easy but not flexible. Thanks again for your great work.
Can esp32 io pin 0 to gnd
What was the code use,
Quite interesting you have not used any voltage regulator and your esp32 is also working well with lipo battery, how it's possible
@@Gocast2 Battery charging module don't regulate voltage
please make video of pograming esp32 use fdti .
Bro, can we compact the wrover module( TTGO TT-CALL). Please let me know if possible, bro.
Link to the module? People help people who help them help them
Dear Mr. Sachin I want to buy this breakout board soldered with ESP32 Chip from JLCPCB using their SMD assembly service. Will they have readily this Break out board design to supply along with ESP32 Chip. If not available can you post a UA-cam video, the PCB design for the Break up board. It will be very useful for subscribers who can not solder the chip on their own but to use JLCPSB's SMD assembly service. Or at least post/ reply the link where this design is available in internet. Please reply.
Thanks for the nice videos,
but how much power does your designed board consume?
Is this first thing that you showed us, either Module Or Chipset ??? It was looking as model more than looking chipset. Esp32 chipset could be smallar than what you showed us.
One question I would like to buy a large number of esp32 chips, where could I buy them with the bootloader?
Connect with us, we can provide you
Just WhatsApp on - +91 82000 79034
Do I need the Reset and Power Button for programming (Bootmode) at the ESP 32 - S2 Wroom Module? I havent planned these on pcb.... is there any other way?
You have to follow this on every ESP modules
@@techiesms thx, great video ... btw
Also.. plz tell how to use the esp8266 chip in a similar way.. BTW Great work.. Keep it up
Yes you can
Are you using it for future projects, like home automation
Well…..
Just subscribe the channel
&
You’ll get the notification for that video
Soon…….😉
Since 3 year subscribed
Only youtuber maker using the epic dialog-
Bhag!😜
Hahaha 😝
Unable to Join.... Unexpected Error - OR-RWE-03. Please look and help me to join.
Hello, whats the package size of resistors?
Let me guess 0603
"A fatal error occurred: Serial data stream stopped: Possible serial noise or corruption."
I was getting error like this. Is it hardware issue or software configuration issue?
Can you please help me to resolve it
Same error with me
Hi, great video. I have a question. I bought an ESP Wroom 32D, I can't programming it. I have tried many different schematics, I have contacted many people's and consulted various blogs and videos, but no one could help me. Arduino IDE give the error about serial communication. I tried to program esp using ch340, co2102 and various Arduino board, but no one helps me
What’s the error?
@@techiesms I have already solved. Basically I didn't connect GPIO12 to ground, I didn't put resistor between GPIO2 and ground and I have connected NC with GPIO23. After solved these error, I could able to program the esp without problems
Amazing
@@techiesms yes. It's very difficult find a correct schematic for esp32. I tried various ones, but only one works for me
Hi Sir, please let me know how can I determine accurately the RAM ROM and EEPROM size of a microcontroller for a professional project? Waiting for your reply, Jayabrata Biswas
from it's data sheet?
@@aayush_789 My question is for a specific program what should be my required RAM and ROM will be?
Suppose I have done a project in Arduino nano. How much RAM or ROM will be optimum for this project if that code will run on a microcontroller?
Or in other words if I write a program in Assembly language how I determine the required size of RAM and ROM that a microcontroller should be so that it would operate properly?
@@jayabratabiswas01 Create your program, compile it and see the size of compiled file. Choose a microcontroller with more than that size in ROM.
are esp32 dev board and nodemcu the same thing?
I think nodeMCU is the esp8266 module
Hey! Where to buy ESP32 chip in Ahmedabad? Any clues?
Search for Sunrom electronics
It’s in Isanpur,ahmedabad
You’ll get there
Sunrom purchase links are expensive than in Amazon, Any cheaper alternative sites other than chinese sites?
well I purchased from that website so I left those links
You called module a "chip". :) A chip (black IC) really resides under metal cover of the module. Anyway, thanks! Good idea, indeed.
Wouldn't it be better to put the lock INSIDE?
not uploading could you help me
I use ota to code it....😎
Can I use the same method with ESP8266 chips? Thanks.
Yes
You can program that using nodemcu board
@@techiesms okay
Thanks👍😊
❤❤❤❤❤❤❤
Lockdown hatwao pehle 🔥
making a watch bot for trading forex
Please make a video on the difference between the ESP8266 chip and ESP32, and also on NodeMCU vs the ESP32 board. Thanks
Smart ir blaster bana de bhai request kri thi 50 baar