Well done! Thanks! I appreciated your illumination with old shop light & incandescent bulb. Also good was not having to remove the leads to the colis! $400+ saved from dealer shop!
found a spec on a blog site - says 13.3 ft lbs. I'm setting my torque wrench to 14 (old analog wrench) and calling it good. Thanks for the video@@Subariblet
Nice vid, my brother showed me but he didn't understand I have a GT and from the angles I'm seeing your engine either sits higher than mine or is more foward because my rear spark plug is directly blocked by the frame
The rear drivers side plug is always the worst on Subaru’s. I’m guessing that is the one you are talking about. I’m not sure what the frame situation is on the GT. I did my Crosstrek too and that plug was way worse than this one. Hardly no room between the frame and the hole. Like maybe 1.5 inches. Had to piece the parts in to get to the plug. I’ve heard it’s expensive to take it somewhere because sometimes they have to raise the engine which is ridiculous.
Amazing video. I am doing my research and will be attempting this myself as I am being told by subaru that it will cost $680 for this service (getting my 60K service). I wanted to ask if you used any antiseize? or any other items not mentioned in the beginning of the video? (ratchet, extension, 14mm sparkplug socket, and sparkplugs)
@@dwdchen5514 Get the “thin walled” 14mm spark plug socket. It will give you a little more room. Just search it up and use the words thin walled and they will pop up.
Took me 10 hours my gf got a v6 there was a spark plug on the driver side that took my 6 hours to do bc I couldn’t get to it bc the space was 2 in wide I had to wiggle and maneuver shit was wild but the the passenger side took me a hour so much easier
Man that’s crazy. I read some threads that said that the V6 were really difficult. The 4’s are enough of a problem but the 6’s practically impossible. They should make the engineer that came up with this setup the change the spark plugs in his garage by himself with regular tools before they release a car.
@@Subaribletyeh the 6 banger has 3 on each side the passenger side there was space even for the one in the back but the driver side I allmost gave up I got the fucker off and had get a skinny Rachet w a extension for the spark plug socket then had to grab it w my hand I’m re living this terror right now 😂😂😂
Those two vertical 14mm bolts to the frame rail derailed my complete sparkplug replacement work. Hummed along on the passenger side, but those factory torqued bolts to the battery box was a showstopper. Need an extra long 14mm wrench to complete this project. Thanks for a good DIY video.
Well done! Thanks! I appreciated your illumination with old shop light & incandescent bulb.
Also good was not having to remove the leads to the colis! $400+ saved from dealer shop!
Thanks!
They gonna charge me 580 for everything I never changed the spark plugs in a Subaru. Only fords and Mitsubishi but imma give it a try
Excellent and very helpful video 👌🏾
Great video, thanks for posting. Going to do the plugs on my 2014 Legacy in the next couple weeks. Did you have to gap those plugs?
@@ChunkStyle These particular spark plugs were pre gapped so I did not have to gap them.
Thank you so much!
whats the wrench size to take the passanger side box out i know you need an extension?
10mm
@@Subariblet thanks
Do I need to replace the spark plug tube seals when I do this? Only have 60k on it
No. I didn’t replace mine.
Thanks brother, very helpful video
torque for plugs?
I have no idea. They are just snugged up. Didn’t want to strip them out in the aluminum.
found a spec on a blog site - says 13.3 ft lbs. I'm setting my torque wrench to 14 (old analog wrench) and calling it good. Thanks for the video@@Subariblet
They didn't look tight enough to me but hard to tell.
Much needed for my project today. Great Video!
Nice vid, my brother showed me but he didn't understand I have a GT and from the angles I'm seeing your engine either sits higher than mine or is more foward because my rear spark plug is directly blocked by the frame
The rear drivers side plug is always the worst on Subaru’s. I’m guessing that is the one you are talking about. I’m not sure what the frame situation is on the GT. I did my Crosstrek too and that plug was way worse than this one. Hardly no room between the frame and the hole. Like maybe 1.5 inches. Had to piece the parts in to get to the plug. I’ve heard it’s expensive to take it somewhere because sometimes they have to raise the engine which is ridiculous.
how the hell did u get those bottom two bolts holding the battery case? my god mine are so tight its unreal
It was a pain to get out. Hardly no room and used a longer wrench because I couldn’t use a socket.
Great video, thanks! Did you lift the engine a bit to access the rear driver side spark plug?
No engine lift needed. It’s tight but can be done just like I did.
Amazing video. I am doing my research and will be attempting this myself as I am being told by subaru that it will cost $680 for this service (getting my 60K service). I wanted to ask if you used any antiseize? or any other items not mentioned in the beginning of the video? (ratchet, extension, 14mm sparkplug socket, and sparkplugs)
If you use the same NGK plugs that I used, you do not need anti seize. NGK does not recommend that on their plugs.
@@Subariblet thank you!
@@dwdchen5514 Get the “thin walled” 14mm spark plug socket. It will give you a little more room. Just search it up and use the words thin walled and they will pop up.
thank you I appreciate the advice. Any tips to make sure I am not over tightening it?@@Subariblet
So there’s only 5 spark plugs i got a 2016 legacy
5? Mine is a 4 cylinder. Do you have the 6 cylinder then?
Took me 10 hours my gf got a v6 there was a spark plug on the driver side that took my 6 hours to do bc I couldn’t get to it bc the space was 2 in wide I had to wiggle and maneuver shit was wild but the the passenger side took me a hour so much easier
Man that’s crazy. I read some threads that said that the V6 were really difficult. The 4’s are enough of a problem but the 6’s practically impossible. They should make the engineer that came up with this setup the change the spark plugs in his garage by himself with regular tools before they release a car.
@@Subaribletyeh the 6 banger has 3 on each side the passenger side there was space even for the one in the back but the driver side I allmost gave up I got the fucker off and had get a skinny Rachet w a extension for the spark plug socket then had to grab it w my hand I’m re living this terror right now 😂😂😂
That battery box is a huge pain in the ass 😂
Yes it is 😂
Those two vertical 14mm bolts to the frame rail derailed my complete sparkplug replacement work. Hummed along on the passenger side, but those factory torqued bolts to the battery box was a showstopper. Need an extra long 14mm wrench to complete this project. Thanks for a good DIY video.