You want a good trick for stripped screws in plastic. get a roll of ABS 3d printer filament. the small roll, cut a piece of it put it in the plastic hole, with a little bit of CA glue (superglue) to hold it in. and put screw in hole. and yes, a roll of the filament will last a lifetime. also, you can take it out and put it back and it will still hold.
there is a reset in the plastic that the bolt goes in when built correctly its fine worth a check if rubbing i had ame issue rebuilt it saw the problem now its fine
About your radio tray issue, is there anywhere underneath the tray where the screw goes into to put lock nuts underneath? as that's what i normally have to do on my race cars.
replace that 1000mah battery 2 x 7,4 volt servos gonna kill that real fast out bashing get a decent one from Answer RC XTR Receiver Battery Flat LiPo 7.4v 2400 Mah V2 i use this in my S35-4 Worlds Edition
@@HaggardRC nice. I really did not try much. I drilled a few times. Then i was like my mate Haggard RC could deff yous this OS and he will run it and make some nice content. Lovely mate. Sounds nice. But you can not expect the best performance out of it. It is like a 5.0 302 Ho smoking out the left bank from being loose from all the nitrous .💯🥇take care . Keep the minions safe and warm. Stay positive my friend. Thank you again
Push a bit of match stick in the stripped hole and the screw will grab fine.
You want a good trick for stripped screws in plastic. get a roll of ABS 3d printer filament. the small roll, cut a piece of it put it in the plastic hole, with a little bit of CA glue (superglue) to hold it in. and put screw in hole. and yes, a roll of the filament will last a lifetime. also, you can take it out and put it back and it will still hold.
You tube changed you man, new savox servos 😂😂 once upon time it was recycle only 👍 nice buggy dude
Nice bud sound good
I had the problem with the servo horn rubbing on the servo too. I think there are other servo horns with more offset ;)
there is a reset in the plastic that the bolt goes in when built correctly its fine worth a check if rubbing i had ame issue rebuilt it saw the problem now its fine
Haggard keep up with new videos tank you for being good UA-cam channel 👍💯😎🎊
Hag !! Hope all is well with ys 👊👊 watching now!! Sounded good with that race time Brother 😂😂 More videos you old HaG 😂😂 take care Brother!!
Will you do the start of the savage build as a live stream?
About your radio tray issue, is there anywhere underneath the tray where the screw goes into to put lock nuts underneath? as that's what i normally have to do on my race cars.
replace that 1000mah battery 2 x 7,4 volt servos gonna kill that real fast out bashing get a decent one from Answer RC XTR Receiver Battery Flat LiPo 7.4v 2400 Mah V2 i use this in my S35-4 Worlds Edition
Looking for ssk Thunr Tiger pull starter bud
On the radio tray. Fill the screw holes with baking soda then a drop of ca glue and re-drill the holes.
Good idea
when storing nitro's you are supposed to keep the piston bottom of the cylinder bdc that help with first start up
Sorry mate. I watched at 5am and forgot to comment. Nice buggy. You have 2 lovely platforms
Thanks, I got that 30VG running well this evening!
@@HaggardRC nice. I really did not try much. I drilled a few times. Then i was like my mate Haggard RC could deff yous this OS and he will run it and make some nice content. Lovely mate. Sounds nice. But you can not expect the best performance out of it. It is like a 5.0 302 Ho smoking out the left bank from being loose from all the nitrous .💯🥇take care . Keep the minions safe and warm. Stay positive my friend. Thank you again
another trick for stripped plastic, a melted zip tie.
What’s that on the cooling head !?
Do you mean the engine heater? 🧐
@@HaggardRC oh ok I was thinking that what it was