The following data relate to a cam profile in which the follower moves with uniform acceleration and deceleration during ascent and descent. Minimum radius of cam 25 mm, Roller diameter 7.5 mm, Lift = 28 mm, Offset of follower axis 12 mm towards right, Angle of ascent = 60°. Angle of descent = 90°, Angle of dwell between ascent and descent = 45°, Speed of the cam= 200 rpm Draw the profile of the cam and determine the maximum velocity and the uniform acceleration of the follower during the outstroke and the return stroke.
Dear In this video u have not explained that how to draw the displacement diagram. For that u can please see the complete playlist from my channel. All the best..... The complete playlist is at follows: ua-cam.com/play/PLhcTfWz-LJxNUtHMoVBlA8S00KHxrOhqU.html For Displacement Diagram pls follow the following link: ua-cam.com/video/Y2UA830Qphk/v-deo.html
sir why is( s )value 0.04 during outstroke and 0.05 during return stroke calculations why are the values different i thought it was only 0.04(40 mm) for everything
The following data relate to a cam profile in which the follower moves with uniform acceleration and deceleration during ascent and descent. Minimum radius of cam 25 mm, Roller diameter 7.5 mm, Lift = 28 mm, Offset of follower axis 12 mm towards right, Angle of ascent = 60°. Angle of descent = 90°, Angle of dwell between ascent and descent = 45°, Speed of the cam=
200 rpm Draw the profile of the cam and determine the maximum velocity and the uniform acceleration of the follower during the outstroke and the return stroke.
Its very straight doubt to everyone , that how to divide 100 and 90 degree by same scale into 6 equal parts .
Or either it taken approximately?
Dear In this video u have not explained that how to draw the displacement diagram. For that u can please see the complete playlist from my channel.
All the best.....
The complete playlist is at follows:
ua-cam.com/play/PLhcTfWz-LJxNUtHMoVBlA8S00KHxrOhqU.html
For Displacement Diagram pls follow the following link:
ua-cam.com/video/Y2UA830Qphk/v-deo.html
sir why is( s )value 0.04 during outstroke and 0.05 during return stroke calculations why are the values different i thought it was only 0.04(40 mm) for everything
Dear
u r correct...
it was a clerical error only...
Nice Interpretation..All the best
How to divide equal parts in displacement diagram
Dear kindly check the following video link to understand the displacement diagram
ua-cam.com/video/Y2UA830Qphk/v-deo.html
Thank you sir❤
Sir please make a video for disk cam with oscillating flat face follower. Badly needed it 🙏😭
sir can you post solving video on the above question please?? i want to know how to solve that problem.. please help me sir
Off-set circle not showing
Dear Kindly see the following link to understand the offset circle question....
ua-cam.com/video/1yaPumvnE_Q/v-deo.html&pp=gAQBiAQB
Offset 15mm draw cheyyaledhu🙄
ua-cam.com/video/1yaPumvnE_Q/v-deo.html&pp=gAQBiAQB
Se the above link....
Sir u didn't draw the offset circle
Sandeep
the question is covered in two videos...
check this link for offset follower part of the question..
ua-cam.com/video/1yaPumvnE_Q/v-deo.html
@@TECHCAD tnq sir 🙏🙏
How can I contact you?
dear
u can contact at enquirecad@gmail.com