@@mehdibessaad3388 Dear sir, Because some configuration of channel not correct sir like selection hardware to voltage but configuration amp it will has some fault. But we can use it for other channels that we make correct configuration. Thanks!
I have a problem: I set the range from 0 to 100% for example, Why when I do the test if I put 0 as a value It gives me 3.5 mA and if I put 100 It gives me 17.5 mA on the tester. The only difference with your settings, Is that i set 2 wire configuration and not 4 wire.
Dear sir, First please check the configuration of hardware such as connections, power supply 24VDC? Second please check the scale setting of 2 wire and 4 wire of scaling block and test again. Thanks
hello sir, thanks foe tour great videos ı have the same analog module ı had a temperature transmitter 2 wire 4-20ma output ı set everyting the same with you and ı wired m+ to my transmitter positive and m- to my transmitter negative ı saw 32767 value or -32767 İ am not sure what is the problem. ı saw when ı put a multimeter between analog card ma- pin and transmitter- pin ı saw 6ma value what is the problem what is my mistake
Same analog configuration and it's used two wire thermocouple sensor at each 8 channel I'm facing SF singnal even having 24v supply at pin 1 and 20 Please is their anything else to check
@@generaltechnologyknowledge5165 thanks for reply sir Actually it's running system for long time and suddenly all 3 AI module has SF fault and online diagnostic module status is ok
Dear sir, We cannot do it with running system. Please do it with stop system. Because it will effect to other modules or other machines during running. I'm not recommend to replace during running system. Safety first! Thanks you!
4 wire configuration not found in your vedios
Dear sir,
Let me create it
Thanks
@@generaltechnologyknowledge5165
Sir your aproch is very good .
Appreciate your reply
I will share your vedios to all my friends related plc
@@immadhussain4319 Thanks sir
@@immadhussain4319 Thanks you so much sir,
I will share what I have.
Thank you very much for this video , all your videos are very valuable.
My pleasure!
Excellent video Sir.i believe this is a complete tutorials hehe.
Dear sir,
For PC we used other software like Modicon... or some software that can link with PLC S7-300.
Thanks
My pleasure!
Why the led sf is on?? Do you have any problem??
@@mehdibessaad3388 Dear sir,
Because some configuration of channel not correct sir like selection hardware to voltage but configuration amp it will has some fault.
But we can use it for other channels that we make correct configuration.
Thanks!
Input analog sir you used potentiometer sir to adjust 4 to 20ma.hehe pls show in the camera Sir.thank you Sir.
Thank you for Response Sir.
My pleasure
I have a problem: I set the range from 0 to 100% for example, Why when I do the test if I put 0 as a value It gives me 3.5 mA and if I put 100 It gives me 17.5 mA on the tester. The only difference with your settings, Is that i set 2 wire configuration and not 4 wire.
Dear sir,
First please check the configuration of hardware such as connections, power supply 24VDC?
Second please check the scale setting of 2 wire and 4 wire of scaling block and test again.
Thanks
None of the lights are changing on your analog input module, how do you get them to show up?
Please check your configuration and try again
hello sir,
thanks foe tour great videos
ı have the same analog module
ı had a temperature transmitter 2 wire 4-20ma output
ı set everyting the same with you
and ı wired m+ to my transmitter positive and m- to my transmitter negative ı saw 32767 value or -32767 İ am not sure what is the problem.
ı saw when ı put a multimeter between analog card ma- pin and transmitter- pin ı saw 6ma value
what is the problem what is my mistake
Dear sir,
Thanks, please check your selection between hardware and software for setting.
What software that you use? TIA Portal or Simatic Manager?
@@generaltechnologyknowledge5165 ı use simatic manager ı selected 2 wire configuration on software as you showed
How to absulte Encoder thank you
Same analog configuration and it's used two wire thermocouple sensor at each 8 channel
I'm facing SF singnal even having 24v supply at pin 1 and 20
Please is their anything else to check
Dear sir,
Please check software configuration on each channel must be the same as hardware selection.
Thanks
Anyway I will create more video about how to connect Thermocouple with two wire connection for you.
Thanks
@@generaltechnologyknowledge5165 thanks for reply sir
Actually it's running system for long time and suddenly all 3 AI module has SF fault and online diagnostic module status is ok
@@generaltechnologyknowledge5165 it's always appreciated efforts to guide us thank I hope it's will helpful to
@@somnathwaghmare51 My pleasure!
Can i replace an AI module for a Running system? If I want to replace an AI module with a same new module in an Running system then what to do?
Dear sir,
We cannot do it with running system.
Please do it with stop system. Because it will effect to other modules or other machines during running. I'm not recommend to replace during running system.
Safety first!
Thanks you!
@@generaltechnologyknowledge5165 it's ok,But if I do then what types of problem can be occurred?;and what types of fault can be create?
@@sujitkumarsantra5996 Sorry sir,
Please detail the problems! what is the fault?
Thanks you!
Hello. Do somebody want to buy 6ES7331-7TF01-0AB0?