Cutting Board 101 & 102: How to Make a Cutting Board -Tips from Hundreds of Boards Made

Поділитися
Вставка
  • Опубліковано 11 чер 2024
  • How to make a cutting board. I've made hundreds of cutting boards in all kinds of styles. This video walks you through how to make a cutting board; primarily focusing on Edge Grain butcher block styles. In this video there are tips for beginners as well as advance techniques for more refined boards too. Of course it's loaded with tips and tricks along the way too.
    #cuttingboard #choppingboard #woodworking
    -⏱Timestamps⏱-
    00:00 Cutting Board Intro
    02:12 Wood Selection
    04:15 Milling Wood
    05:26 Edge Grain Cuts
    06:03 Patterns
    07:07 Face Grain Boards
    07:49 Surfacing Strips/Superior Glue Ups
    13:43 Glue Up Tips
    15:33 Flattening Boards
    16:13 Warped Board Solutions/Troubleshooting
    18:43 Squaring Board
    19:00 Juice Grooves
    20:26 Handles
    22:11 Clean Burn Marks
    22:49 First Sanding
    23:53 Branding
    25:08 Edge Profiles
    25:32 Sanding Tips
    27:05 Raising the Grain
    28:27 Wood Finish
    30:57 Oiling Boards
    31:56 Super Smooth Boards
    32:25 Wood Wax
    33:25 Final Tips
    -🔨Tools/Supplies I Use🔨-
    www.amazon.com/shop/6_8woodworks
    -As an Amazon Associate, I earn from qualifying purchases.-
    Disc Sander for Table Saw: amzn.to/46Mzgsi
    Benchtop Jointer: amzn.to/3uNrG3n
    Jobsite Table Saw: amzn.to/3sw2A2G
    DeWalt Planer: amzn.to/3sutCaF
    Helical Planer (a bit more, but amazing upgrade) amzn.to/3GtFtOT
    Router: amzn.to/3HqKNSV
    Drum Sander: amzn.to/3NSkLdS
    Wood Glue: amzn.to/3tYoxb8
    Starbond CA Glue Kit: amzn.to/3l9fS4p
    Juice Groove Bit: amzn.to/2YV305M
    Cutting Board Oil: amzn.to/3RtUbMf
    Mineral Oil: amzn.to/3tZ55Lf
    Board Wax: amzn.to/3u0gmey
    Heat Gun: amzn.to/3Rs6fh5
    Round Nose Bit: amzn.to/3COYYBd
    Juice Groove Scraper: amzn.to/3dYBZJt
    Benchtop Sander: amzn.to/3AoyRxZ
    Chamfer Bit: amzn.to/3b33rUZ
    1/8" Roundover Bit: amzn.to/3QTVX6L
    1/4" Roundover Bit: amzn.to/3pMz0Gt
    Cove Bit: amzn.to/3AOuj5x
    Large Cove Bit: amzn.to/3TbUv3F
    Router Lift: amzn.to/3Qgpojv
    Matchfit Clamps (Straightline Jointer Jig): amzn.to/485KNUq
    Pushstick: amzn.to/4a4tdSH
    Tung Oil: amzn.to/3TfPTXN
    Citrus Solvent: amzn.to/3AqIRH5
    Premixed Tung Oil & Solvent: amzn.to/3CynEgV
    Wood Wax: amzn.to/3pJhnHN
    Orbital Buffer: amzn.to/2QfjzbK
    Light Scouring Pads: amzn.to/3uGW7Dj
    Buffer Bonnets: amzn.to/3w9IRrh
    Air Compressor: amzn.to/47KsSD3
    To learn more about the lasers, check out this link: www.xtool.com/?ref=QeZa4pIV3R...
    (Purchases made using this affiliate link helps support the channel and enables more content like this.)
    💡Promo Code ($80 off Use code: xTool68)💡
    💵US Store: bit.ly/43cjsP8 (Use code: xTool68)
    🍁CA Store: xtool.pxf.io/jr0qGM
    💶DE Store: bit.ly/49KwvKc
    💷UK Store: bit.ly/3Tf0QcJ
    💶EU Store: bit.ly/48Sh7ua
    💶FR Store: bit.ly/4c5upq1
    ➡️xTool P2⬅️
    💵US: bit.ly/3PhBxWk
    🍁CA : xtool.pxf.io/zNGJ9G
    💶DE: bit.ly/3TdE4lB
    💷UK: bit.ly/3Vfny7k
    💶EU: bit.ly/4ad3B5r
    💶FR: bit.ly/3wQBZ7G
    ➡️xTool S1⬅️
    💵US: bit.ly/4c8eC9L
    🍁CA : xtool.pxf.io/Or0P3P
    💶DE: bit.ly/3Vb714l
    💷UK: bit.ly/3wZCvjE
    💶EU: bit.ly/3VbLSXN
    💶FR: bit.ly/3ThgODj
    ➡️xTool F1⬅️
    💵US: bit.ly/3Tlqzk6
    🍁CA : xtool.pxf.io/dag6j2
    💶DE: bit.ly/3wTlJTu
    💷UK: bit.ly/43dlajx
    💶EU: bit.ly/3v8NBT0
    💶FR: bit.ly/3IywehF
    This sander and the foam abrasives are truly a game changer! ZERO HAND SANDING ON CUTTING BOARDS....INCLUDING JUICE GROOVES! But seriously...The 3x4 Sander, foam abrasives, other abrasives and more can be found at surfprepsanding.com Use my affiliate code “68WOOD” for 10% off your order and to support the channel. It's a game changer. Seriously.
    -📸Instagram🎥-
    / 6_8woodworks
    -💻Website💻-
    www.sixeightwoodworks.com (Items will be updated 12/10-12/11/23)
    6% of sales donated to Orphan Care organizations, 8% of sales donated to Foster Care organizations, and 6.8% donated to the Equal Justice Initiative
    To see different cutting board handhold ideas, check out: • Cutting Board Handles
    For more about woods I use, where to buy the wood, and other tips and info, check out my Wood 101 video: • Wood 101 For Woodworke...
    Wood Whisperer Food Safe Finish Video: • Stop Using Mineral Oil...
    Wood species I commonly use with cutting boards: Walnut, Cherry, Maple, Sapele, Padauk, Mahogany, Jatoba, White Oak, Wenge, Yellowheart, Morado, Curly Maple, and more.
    I always encourage the recipients of my boards to use them! All those extra steps are taken to make it food safe, so why not use it for more than kitchen decoration. To get ideas for other board uses, check out: / useyourboards
  • Навчання та стиль

КОМЕНТАРІ • 83

  • @thomaschandler4831
    @thomaschandler4831 5 місяців тому +4

    The fact that you teach your Son your craft makes me glad I watch your channel and now I’m a subscriber … he is the future of your family and business … also you do fabulous work and I appreciate your teachings.

  • @chrisroyak4479
    @chrisroyak4479 6 місяців тому +2

    Great sequel to the original! As someone who watched the first "Cutting Board 101" video intently (learned A LOT!), it's great to see that there's always new things to learn! Really appreciate the time you take to share the latest and greatest with everyone! Also... it's cool to be able to drop by the set from time to time! All the best!!

  • @larrybaker5316
    @larrybaker5316 3 місяці тому +1

    thanks for sharing. your son looks like a natural wood worker!

  • @joyous7777777
    @joyous7777777 5 місяців тому +3

    Love the Micah 6:8 reference! It's the only way to live! Thanks for your tutorials!

    • @victoryak86
      @victoryak86 3 місяці тому

      One of those verses that’s kind of a “life verse.” It covers the inner state of my heart, how I should live and be among others (loving true Justice while cultivating mercy towards those in such need for it; and then the humility we must have as we “walk” with Our God. Oh for grace to live this way!

  • @rickpouley7561
    @rickpouley7561 6 місяців тому +3

    Love it to see your son working with you on your projects!!

  • @UAL012
    @UAL012 Місяць тому

    My friend, your cutting board patterns are inspirational. I have a LOT of scrap wood that I picked up for free and have been trying to figure out some patterns. Thanks to you, I have some cool ideas I want to try out.

  • @Sebastopolmark
    @Sebastopolmark 6 місяців тому +2

    Hey Nick, thanks for taking your time to make our projects, so much, better. The tips and tricks are always well received. I hope you and ALL your kids have a GREAT holiday season. My daughter is a middle school special ed teacher and as I tell her, Carpe Diem! !! !!!

  • @ToolsandTime
    @ToolsandTime 6 місяців тому

    Cool tips and really awesome looking boards!

  • @woodworks2123
    @woodworks2123 6 місяців тому

    Great in-depth video with some great tips to get that end product a bit better.

  • @dennisdownes9319
    @dennisdownes9319 3 місяці тому

    Great video! Thanks DD

  • @vninjadfw
    @vninjadfw 6 місяців тому

    Incredible video! Great job.

  • @aaronkarger814
    @aaronkarger814 4 місяці тому

    Great video I learnt a lot I needed to change in my next chopping board

  • @hardtruth63americanpatriot66
    @hardtruth63americanpatriot66 5 місяців тому

    Great video, bro! Keep them coming!

  • @mrcig3
    @mrcig3 3 місяці тому

    CONGRATULATIONS ON 100K SUBSCRIBERS !!!!!

  • @vcap7886
    @vcap7886 6 місяців тому

    Great video! Love the family helper! Subscribed,,,,

  • @XxBloggs
    @XxBloggs 5 місяців тому

    Great video

  • @joelcopeland3018
    @joelcopeland3018 6 місяців тому

    Great video... Very nice boards and your son looks like he is a great helper.

  • @vdice2
    @vdice2 Місяць тому

    Great Work. I've been using Goldman's Wood Balm for finishing cutting boards. It works well.

  • @user-kj3xs2uq4y
    @user-kj3xs2uq4y 5 місяців тому

    Thank you for this video!!! There are so many videos out there that just show banging thru the process but don't really talk about what to really expect. This is exactly what i needed to get past the fear of trying these. Thank you, thank you!!! do you happen to have any videos out there how to utilize good dimensional small pieces? Like how to glue up small pieces to make usable larger pieces for boards?
    mg

  • @benjaminbrookins9273
    @benjaminbrookins9273 5 місяців тому

    Great vid man. I’ve been making and selling boards for a few years. Glad your son loves this stuff too. Wood like to see an in depth review of your drum sander sometime

  • @befmx31
    @befmx31 6 місяців тому

    Beautiful boards.

  • @guybowers9094
    @guybowers9094 6 місяців тому

    Appreciate the great video. I have yet to make a cutting board and the tips will help me when I do make one

  • @victoryak86
    @victoryak86 3 місяці тому

    One thought about avoiding snipe, perhaps prep the longer boards first before cutting them. I’m sure you do this as well, just tossing it out there👍. On the glue clean up do you ever wait for just like an hour or so (or whatever the sweet spot is) so the glue isn’t sticky but still flexible for easier clean up. I find it want to do this but don’t always time it well. Great channel and example of being a wonderful dad. Love to see young people getting after it in the shop! God bless.

  • @EversoleNathan
    @EversoleNathan 5 місяців тому

    Subscribed. Great Video!!

  • @BradyFlanary-kw8zz
    @BradyFlanary-kw8zz 2 дні тому

    Great content and step by step instructions.
    I've just completed my 1st cutting board and it looks awesome.
    Now that it’s completed i’am concerned that the humidity level of the wood before the construction may be wrong? The wood was purchased as rough cut lumber and air dried for 1 year. I milled it down to my specifications. How should I be sure that moisture within the wood isn’t a problem on my next cutting board. The 1st one looks fine so fare but it’s only been a couple days of completion.

  • @markduggan3451
    @markduggan3451 6 місяців тому

    Very nice boards.

  • @togger2151
    @togger2151 3 місяці тому

    I like the idea of the disc sander for the table saw. What grit do you use for surfacing for glue up?

  • @CreativeCustomDesigns
    @CreativeCustomDesigns 6 місяців тому +1

    I'm just finishing up my first batch of boards ( cutting and charcuterie ) I'll be looking at the sanding products that you came across.. I also picked up a couple other tricks that I'll use on the next batch
    Thanks for this video Nick.

    • @SixEightWoodworks
      @SixEightWoodworks  6 місяців тому +1

      Awesome! Good luck with your boards!

    • @CreativeCustomDesigns
      @CreativeCustomDesigns 6 місяців тому

      @@SixEightWoodworks If I wipe water on the boards, then wipe it off after a couple mins.....is that long enough? Or do I need to let it sit longer?

    • @Renrondog
      @Renrondog 4 місяці тому +1

      That's long enough , even just a spray then wipe for a minute is enough. Just want to raise the grain once then sand it down
      @@CreativeCustomDesigns

  • @jasonmadison4599
    @jasonmadison4599 Місяць тому

    You inspired me to make cutting boards and sell at my first craft show in May. I see with your boards you include a little information paper (woods, care, etc.). Would you mind sharing what you provide when you sell your boards?

  • @handymadness
    @handymadness 6 місяців тому

    Did you buy that Surfprep system after my advice I left on your original video years ago? I remember writing a long comment on saving your hands on the grooves with that system.

  • @icecreamladydriver1606
    @icecreamladydriver1606 4 місяці тому

    When you start getting the cutting boards looking good how do you determine how much to sell them for? Thanks.

  • @jeffsimmons658
    @jeffsimmons658 Місяць тому

    I have a quick question for you.
    I am new to woodworking and I’m starting little projects.
    The first one was a cheeseboard. I used a planer jig (melamine )with my Dewalt 735X.
    As I was planing my wood, I noticed that one end of my 20” board was becoming much thinner.
    Was I shimming the wrong end of the board?
    Did I need to flip over my board?
    Lastly, on my planer there’s a round wheel on the left side called a Turret Stop. I have mine set a 1/8”. Is that where I want it set and when would I change that?
    Thanks
    Jeff

  • @user-vn2lq8qb6f
    @user-vn2lq8qb6f 4 місяці тому

    How do you figure what you charge for your boards. I’m new and still figuring out the finances of the business. Great video and have subscribed to learn as much as possible.

  • @edivdp
    @edivdp 5 місяців тому

    Wondered what the "6:8" was on your apron and it's on your wall! Nice scripture!

  • @terryreichel7193
    @terryreichel7193 2 місяці тому

    I am beginning at the cutting boards. What glue do you recommend and what about food grade?

  • @SkydiveDriver
    @SkydiveDriver 4 місяці тому

    You make everything look so easy thank you for all your tips. I was wondering how do you handel your sales, do you use paypal or what. Your response would be greatly appreciated Thank you

  • @sauron636
    @sauron636 3 місяці тому

    Great video man... i have a question if you have the time I'd appreciate it..... the ca glue its the same as crazy glue ? And if its isn't toxic ? Beginner here not trowing hate your way its just a concern i have

  • @pnwgrown_360
    @pnwgrown_360 5 місяців тому

    Nice dude. Come to my
    Shop in Bellingham!!!!

  • @jamesgoodrich8355
    @jamesgoodrich8355 Місяць тому

    Q for ya. The difference between face and edge? Is that just that the gluing up of taller strips than wider strips? If I'm saying that correctly. Thanks

  • @jeffreymoskovic3499
    @jeffreymoskovic3499 6 місяців тому +1

    Hey Nick, why not use double-sided tape to attach thin strips to thicker board to run through the planer?

    • @SixEightWoodworks
      @SixEightWoodworks  6 місяців тому

      Definitely an option. I usually don’t like to mess with double stick tape that has to be removed eventually, but there’s some better products nowadays and an option for folks to get those thinner strips!

  • @pa.fishpreacher6166
    @pa.fishpreacher6166 6 місяців тому +1

    Greetings, What would be a good lathe for someone who wants to learn to turn wood? Which lathe would you recommend?

    • @SixEightWoodworks
      @SixEightWoodworks  6 місяців тому +1

      I’d say this is the best deal: amzn.to/46SD5fz There are about five companies that have the same manufacturer for this beginner lathe. I have this version as the Rockler “Excelsior” one and it’s great. I have several Wen tools, and they do quite well for the price. I would recommend going with carbide cutters instead of traditional gouges. To maintain the sharpness of my chisels and gouges I had to spend a ton on accessories. So it’s much more affordable to just get a basic set with removable carbide cutters, like this one: amzn.to/4a8m9EJ

  • @Apollyon-er4ut
    @Apollyon-er4ut 4 місяці тому

    New subscriber, having never built a cutting board (river tables & shelves of reclaimed wood is my thing). I came into a 150 year old broken piano. Wood salvage meant lots of oak, a 3x6x5' piece of unfigured cherry (supporting sounding board), and several 3x4x3.5' pieces of old-growth doug fir. Laser straight ultra tight grain w/o a single knot, hard as a rock. Not normal, but could you use as end-grain cutting board? Anyone?

  • @moradmoses3779
    @moradmoses3779 3 місяці тому

    I bet you have the most beautiful cutting boards at home ❤👍

  • @befmx31
    @befmx31 6 місяців тому

    What product do you use from the SurfPrep line do you use to sand the juice grooves? Thanks.

    • @befmx31
      @befmx31 6 місяців тому

      Looking at the video, looks like you are just using one of the square ones and using the edges?

    • @SixEightWoodworks
      @SixEightWoodworks  6 місяців тому

      I use the 3x4 electric ray. It’s fantastic and so versatile for loads of projects. On deeper grooves I just use the pro foam 10mm and 1/2” a little offset on the sander. Works amazingly well!

    • @befmx31
      @befmx31 6 місяців тому

      @@SixEightWoodworks thanks.

  • @sherkiaprather9273
    @sherkiaprather9273 4 місяці тому

    Do you have a project book that shows the measurements and and steps to building the projects

  • @moradmoses3779
    @moradmoses3779 3 місяці тому

    I was wondering if you sell them to individuals! and if you do, how much are they, thank you.

    • @SixEightWoodworks
      @SixEightWoodworks  3 місяці тому

      I do. You can see the price range of my boards at www.sixeightwoodworks.com

  • @user-pr5qt5jm8j
    @user-pr5qt5jm8j Місяць тому

    Really like your channel and life philosophy. Hope to purchase when there are products for sale. Do you have an email list?

  • @JohnClark-tt2bl
    @JohnClark-tt2bl 6 місяців тому

    For the super thin pieces i would use double sided tape to stick them all down together and use a orbital sander. Easier to get them uniform that way.

  • @mpe777
    @mpe777 3 місяці тому

    Beautiful job brother. I’ve been learning some from you so thank you for that. I’m subscribed and follow you.

  • @kevinwalter5373
    @kevinwalter5373 6 місяців тому

    how do i get affiliate help?

  • @shannonm8202
    @shannonm8202 3 місяці тому

    Aren't face and edge grain basically the same thing in terms of the wood itself? I thought the only reason for the terminology of "edge" grain is to give a name to the process of cutting thinner face grain and flipping it to achieve a greater overall thickness.

  • @rogertyler3237
    @rogertyler3237 2 місяці тому

    I Have 2 Sanders A Viberating
    Mouse & sheet Sander.

  • @OurLlama
    @OurLlama 3 місяці тому

    I'm months late here, but epoxy to fill holes on a cutting board seems like a bad idea. CA glue might be food safe, I'm not sure, but I've seen people do sawdust with tightbond glue before, might be a decent alternative

  • @gppatnude
    @gppatnude 5 місяців тому +1

    .INCLUDING JUCIE GROOVES! ===> "JUICE" is spelled incorrectly

  • @rogertyler3237
    @rogertyler3237 2 місяці тому

    If The Glue Squeeses Out
    Won't The Project Be Glued
    To The Clamps & The Table

  • @trex283
    @trex283 6 місяців тому +2

    Your showing the quarter sawn side. So don't always flip the boards. Look at the grain direction.

  • @billnelson9108
    @billnelson9108 Місяць тому

    Great tips except for the idea of gloves and the sander. Never, never use gloves near anything spinning at a high speed. Once it grips the gloves, you could lose a finger or more.

  • @devito770
    @devito770 3 місяці тому

    What grit is on your drum sander for the thin strips?