How one can measure Amp.on both positive and negative wires at a time amp. Can only be measured by using it separately on either Negative wire or positive wire separately Can the Inventor Replay my Question. Thanks.
"When measuring a 3-phase circuit, the clamp meter should be applied around the R, S, and T wires (all three wires) at once. Leakage current can also be measured by applying the clamp meter around a grounding wire."
…a clamp meter around all 3 phases at the same time reads zero unless there is a fault to earth. During non-fault conditions the meter would read zero amps as all the current that flows in, flows back out again, cancelling the input. This one part of the video confirms this is being run by the motor. If it really works, cut the belts from the ‘start’ motor. Even then the alternator could be driving the flywheel as a synchronous motor. Of course, it’s smoke and mirrors. And some second hand electrical control gear.
Totally impossible, there is nothing called free energy in this world. What about friction? If there is no power supply to the fly wheels, it will eventually come to rest after a certain periods of time. Through the initial power supply, you are able to rotate the wheels, but if there is no constant inputs, it will eventually stop. You can never generate energy, you can only convert from one form to the other. @dattabenurcreation , please don't encourage this kind of video in your channel.
@@freaking_natureBoy its not some kind of free energy . Flywheel act as battery it store mechanical energy in the form of rotating flywheel depending on the output load it will slow down aftrer some long duration of time . before battery was invented buses use to run on flywheel base storage called "gyro bus". this is proved concept similar to spring base toys car . since this has huge flywheel when well optimsed it will run for longer idk how much
That's fine, spring based toys is fine, there we provide the tension to the springs to store the energy that later runs the toy. There is some sorts of inputs. But, here it claims 0% input and 100% output!!! Is that possible?
@@freaking_natureBoy oh yah yah ! That point it slip from my mind. That's not possible at all no doubt. Even that gyro bus also use to rotate in a vaccum chamber inorder to reduce friction.
When he put the amp clamp on the wire for input at about 4:30 , he put it around all 3 conductors, amp lamps won’t work around all conductors. When he put it on generator output, he put it on one leg or conductor. This thing is a hoax and can’t possibly work, otherwise he would be a very wealthy man.
Congratulations sir this is very great invention this country requires people like you pl go ahead and start duplicating and solve the power problems.I have seen such unit in Hyderabad but till date it has not been takem off'.
What is the friction losses value couldn't be zero. Reverse current mechanism from the starter motor, Start button from the flywheel machine and stop button from distribution panel, we have more doubts in its process. Mechanical losses, electrical and thermal losses are zero? Not possible
U maths n physics is wrong so u live n believe this is impossible, u've being lied to all ur life, science isn't completely correct ,get that ,why would the entire world no naking fly weel generater ?? Just to trick people? U guys really have n brain!!
The amount of energy input to this machine is much higher that the energy output. Bearing friction losses, drive belt loses, windage losses, motor losses, generator losses, gearbox losses, etc. If the machine is really efficient, at best you may get about 60% of the energy out of the generator that you put into the motor.
@@arthurrichardson3439 I am as an engineer! The free energy generator can produce electricity for a few minutes, but the air resistance, the fraction, the gravitational force, these factors act on the free energy generator and finally stops the free energy generator. But if we have ccount for the equation and keep some energy storage in between (I mean a powerful battery) in this way we can get power for long hours
It's called the Inertial Increase of Electrical Power. It uses inertia to amplify the torque and as such amplify your power input by the motor. Resistance doesn't matter because the motor overcomes it. The amplification comes from the fact that to stop acceleration of a flywheel you don't need to apply an "equal" force but only opposite. The force can be half if the distance from the center is doubled. This works in reverse if your taking power closer to the center which causes the moving mass (further from the center) to produce an amplification of torque. Atleast that's how I understand it. Research Energy Impulse Secrets and Power Impulse Secrets by kanarev for more information. The impulse probably comes from gravity due to the imbalance flywheel. But by using two imbalance flywheel 180 degrees out of phase to remove vibration problems.
While you are checking the input consumption with clamp meter not showing any amp because of you have clamped with insulated negative and positive together running wire. The clamp meter will read only a single polarity wire only. Please don't post like this 0 input with high output.
پاگل بنارھا یہ ملباری پوری دنیا کو صرف یوٹیوب چینل کے لیے پہلے انہوں نے کوشش کی ہوگی فری انرجی بنانے کی لیکن شاید ناکامی اور پروگرام کے وڑ جانے پر یوٹیوب کو لوٹنے کا پروگرام بنا لیا ہے
It's an energy storage device. The utility spins up 2.5 tons of kinetic energy. Then it can supply electrical output from the rotating flywheels. The useful output must be some percentage less than the total input.
How do you give the input energy continuously if the generator consumed total stored energy. Again the 15 kw motor will be started right?? . How much electric energy will be generated per hour after subtraction of input motor energy consumption
Those who are saying it won't work, it's against the laws of physics, they don't understand how really it works. The real secrets are not shown here. The real secrets lies in the windings of alternator. They take the default coil winding out, and put a new coil winding of high impedance high gauge wire, the property of high impedance coil is that it delays the development of magnetic field when current flows through it. In electrical engineering we call it rise time and decay time of magnetic field, which is directly proportional to the impedance. That's why during on load conditions, the alternator coil delays the development of magnetic field and meanwhile the rotor magnet passes by the coil, as a result the coil doesn't repel the approach magnet and doesn't attract the departing magnet, so there's no drag or no lenz resistance, only friction exists and that is overcome by heavy flywheel easily. It's age old technology but doesn't put to the welfare of society. It's hidden and kept for military applications only in countries where it exists.
And how is a "high impedance, high gauge" wire constructed? Is there some special material is it constructed from? That part doesn't make sense because a higher gauge wire will have a lower impedance. And a lower gauge wire will have a higher impedance.
The whole video is a lie. He was driving the flywheels with the motor all the time. He basically turned off the motor driving the flywheel. The electrical load and losses in the system made it stop that quick.
Hi Mr Roshan Nice to see the demo appreciate your project Can you please let me know the cost of your free energy generator for our borewel motor of 15KW
This is very interesting invention.companies should do more reseach to create machine like this one, to produce cheaper electricity to communities. very fascinating.
You said you use EB power only to kick start, and then no power to the primary motor you showed it too I agree.. And the generator was running successfully Good, then you said it is running with the help of some gare box which you invented that's secret OK agree... Later your assistant switched off a switch and the generator stopped what was that switch from where the power supply came to it which motor was switched off could you explain to me please... If you don't give me your address I'll come and clarify my doubts
You are having 3 phase current shifted 120 degrees. When you combine the current on these wires the net adds up to 0. That is why when you measure input wire it is showing 0 in the meter. Don't defraud people like this
@4:30 the amp meter is showing 0 amps. Well it should because all three phases are being measured at once. Even if it were single phase it would also. But monitor a single conductor (as in power wire) at a time ....then you have a true reading and not till then. 😮
They say, once it is started to full speed, the motor gets disconnected from grid, till this point, what they say is correct, but later they say, the motor is totally disconnected from power supply, which is not correct, because the kinetic energy cannot be created and ultimately the flywheels will slow down and stop, to retain the flywheel RPM, we have to give the power supply from the alternator to the motor, so the chain reaction goes on.
Partly. There is no chain reaction happening here. This machine at the most gives you a stable voltage from the generator fed by a fluctuating power supply fed to the motor.
इस मशीन को पहले गती (रनिंग) देना पडता है बाद मे जनरेटर अपनी ऊर्जा (करंट, पावर सप्लाई) देता है ओर बिना पावर सप्लाई से यह मशीन चालू रहती है बडे दो चक्के के आर पी एम के वज से इस मे बडे दो चक्के का खेल है ( गती, आर पी एम, रनिंग समतोल रखना, यह सभी के दिमाख मे नही आता है 100%✔️👌👍😃
If you total all the energy created by generator and used by motor plus losses it must match. So no new energy created dear. I am surprised no one is talking about theory of energy!! It cant be created !!
How much energy is lost in the gearbox? This is very similar to the Adams generator which also uses flywheels, 2 1kW motors and a 10kW generator. The 2 small motors are pulsed to maintain the speed of the flywheel once it has reached sufficient momentum to run the generator and runs quietly and for much longer periods of time if this one only runs for 45 minutes.
Flywheel can produce energy for sometime but by the time you connect a big load to it it will stop spinning the motor shaft will get very tight due to the load
@@shayarchoksi2566 yup he is faking it. Anyone who had played with simple mini motors in childhood by convecting it to an Led to produce electricity shoud already know this. It's basic physics
@@francisappiah8549 nothing run forever without input power. flywheel will stop after some time. friction is on of the culprit loss energy even without output. need hug amount of power to running flywheel.
I’ve always felt certain about perpetual motion machines. Thanks for your contribution. I am sure once we get past human greed we will have a pleather of wonderful creations that make our life more fun
Sorry Sir. We cant get past Human Greed. Everything we do today is guided by both hunger and greed. These guys are both hungry and greedy, sorry to say so. They are selling a 50Kw machine for US$ 60,125. They call this a Deposit. After you buy, then you will wait for 12 months for the machine to be delivered to you after which you pay them 4.0 Indian Rupees for every unit of power you produce. That is GREED WITHOUT BORDERS. These guys are planning to collect ALL the world resources and store it in their houses. This will not be possible and therefore this is a scam, and may be the machine can not work.
Mr. Roshan, please see that you don't confuse electrical energy and total energy. electrical energy can be amplified 15 to 20 folds with low spec machines. don't even need higher weights having flywheels. with regular ebike motors and home made alternators, with sufficient cooling setup, the torque difference between the ebike motors and Alternators can be given and the whole concept just works based on inertia and one more basic idea, that is, the input getting motor's torque to spin at specific rpm should be always greater than the output generating alternator's torque necessity to generate the necessary electrical power. All one need is to know the basic understanding on motors and generators (or alternators) for building this kind of machine.
If the machine is not running on power and flywheels are running alternator with the help of gear box which is generating the power; then how come it can be put off with the help of switch. If switch is provided for alternator to stop producing power, then what is the relationship of alternator with flywheel which leads flywheels to stop
Menurut sy ini blm efektif Karena menggunakan dunamo penggerak Bila ingin efektif Harus gunakan kincir air dimana tidak menggunakan dinamo penggerak melainkan menggunakan air jatuh dari bakpenampungan ( toren air) sehingga kerja dinamo penggerak tdk ada yg ada hanya dinamo mesin air buat mengisi air bak penampung air( toren)sehingga bisa kerja maksimal mesin airnya Dimana air jatuh mutar kincir air dan masuk bak penampung ( kolam air) lalu disedot airnya buat isi air bak penampung diatas( toren )
In this setup, AC Motor continues getting supply. actually motor switch is bypassed inside. what he is showing by clamp-on current meter is false. this wire is three phase ( 3 core ) wire putting clamp-on current over entire cable will show zero current whether motor getting supply or not ,Impossible, there is nothing called free energy in this world. i wonder why he spending so much money on a false project.
According to my understanding there is no energy is created without spending some form of energy. If you spin a flywheel with an electric motor and stop it after some time the kinetic energy will fade away as factors like the friction of the setup plus the load connected to it. For demonstration you can show the voltage until the fly wheel stops as there is no backup for flywheel to keep it running continuously. You can use a flywheel setup to have non iterupted power supply for communication and runway lights used in airports to overcome the voltage buildup delays of a standby generator.I personally have experience in seeing a 650kVa French made SACM make with fly wheel setup with 3 sec.interruption.This is all about a setup in 1978.
No load, it will run for long time. With load only for a few minutes. The motor must work in Island mode and sync to supply through a ups. The flywheel supplies will generate some power in the generator aka motor for a few minutes. When another generator is started or mains power restored, the ups will sync and run the motor from the last speed and keep it ready again. This system can be used only where continuous power is required in a factory like ceramic plants, semiconductor fabs etc. Now for other applications, this is a useless applications. An UPS with Lithium battery power can power the plant until standby genset is started. No mechanical wear outs. Regards.
When the flywheel reaches its rotation to its fullest speed then main power supply to the flywheel motor is cut off. But to maintain the rotation of the flywheel certain amount of eternal power is definately required sir. May be certain amount of power which is generated is drawn back to maintain the rotation of the flywheel. ...There is lot of doubts arising in your explanation. The interviewer should have asked this question in technical perception.
The world will be stunned one day, when it realises that all along the Creator had always given us clean energy , right under our noses. We have only closed up our minds with the little science we thought we knew. We could and now have free electricity without breaking the law of conservation of energy. It has always been in our Physics , but we were all blind to it. Selah!
Dear good efforts, what is the cost of it, second it is too noisy, try to improve it and reduce its noise. During mechanical movement there will be an energy loss, how you recover that loss.
Я изобрел трансформатор эфира. Это обычный трансформатор обмотанный синей изолентой. Суть в том что потребляет он 0 Вт, а выдает 1000 Вт, могу дать схему интересующимся
"free energy" finally happens when all the energy that was used to get the ore, smelt the ore, cast the flywheels, make the iron for the frame, make the copper wiring, the transformers, gear box, motor....all the energy added up needs to be offset by the energy actually created. And then there is the energy to create the money to buy this huge machine, hire a crane to get it on a truck, transport it to the site and set it up to work. You start this thing with a HUGE deficit of energy and there is major catching up to be done just to break even. So you aren't just "creating" free energy on the spot, you have to make up for all the energy put into actually getting it to work at your site. Only then will you start getting "free" energy, which won't happen. so the only person who came out with free energy is the maker in the form of money.
Can we stop complicating things by trying to pretend you don't understand what they mean. If it's so easy to castigate others why not show us your innovation that really works.
a Zero in can only make a zero out.if this would work why are we still building giant wind-wheels and Solar-Modules? Please go to Las Vegas because its a nice Illusion^^
![Lp. Сердце Вселенной #60 РОЖДЕНИЕ ЛОЛОЛОШКИ [Финал] • Майнкрафт](http://i.ytimg.com/vi/YoR0pAV9FVQ/mqdefault.jpg)
I wonder the way you use clamp meter to measure motor current of 3 wire at one instead of one by one
Good question?
To prove you can’t measure it that way
Bravo!
Love from Serbia.
I like the way he measured the current to the motor. What a trick!!! :)
How one can measure Amp.on both positive and negative wires at a time amp. Can only be measured by using it separately on either Negative wire or positive wire separately Can the Inventor Replay my Question.
Thanks.
"When measuring a 3-phase circuit, the clamp meter should be applied around the R, S, and T wires (all three wires) at once. Leakage current can also be measured by applying the clamp meter around a grounding wire."
…a clamp meter around all 3 phases at the same time reads zero unless there is a fault to earth. During non-fault conditions the meter would read zero amps as all the current that flows in, flows back out again, cancelling the input. This one part of the video confirms this is being run by the motor.
If it really works, cut the belts from the ‘start’ motor. Even then the alternator could be driving the flywheel as a synchronous motor.
Of course, it’s smoke and mirrors. And some second hand electrical control gear.
😂😂😂😂😂
Let's find out what college he graduated from..?
Lol, don't disapprove if you know nothing. Can you make a better free energy device?
Totally impossible, there is nothing called free energy in this world. What about friction? If there is no power supply to the fly wheels, it will eventually come to rest after a certain periods of time. Through the initial power supply, you are able to rotate the wheels, but if there is no constant inputs, it will eventually stop. You can never generate energy, you can only convert from one form to the other.
@dattabenurcreation , please don't encourage this kind of video in your channel.
The fly wheel supplies the free! All other components receive! It works
I totally disagree, it won't work.
@@freaking_natureBoy its not some kind of free energy . Flywheel act as battery it store mechanical energy in the form of rotating flywheel depending on the output load it will slow down aftrer some long duration of time . before battery was invented buses use to run on flywheel base storage called "gyro bus". this is proved concept similar to spring base toys car . since this has huge flywheel when well optimsed it will run for longer idk how much
That's fine, spring based toys is fine, there we provide the tension to the springs to store the energy that later runs the toy. There is some sorts of inputs. But, here it claims 0% input and 100% output!!!
Is that possible?
@@freaking_natureBoy oh yah yah ! That point it slip from my mind. That's not possible at all no doubt. Even that gyro bus also use to rotate in a vaccum chamber inorder to reduce friction.
The power to the motor cannot be measured around all 3 conductors, as the sum of their current is zero.
THAT IS EXACTLY RIGHT.
AMPS ARE MEASURED IN A SINGLE WIRE.
His meter was set on Vac
😂
Plz send the pH no
And the gen set was showing 32Amps with no load connected.
When he put the amp clamp on the wire for input at about 4:30 , he put it around all 3 conductors, amp lamps won’t work around all conductors. When he put it on generator output, he put it on one leg or conductor. This thing is a hoax and can’t possibly work, otherwise he would be a very wealthy man.
Haha 0%input 100%output ❎
0%brain 100%idiots ✅
3wire at same time=neutral
Fix, this device is not her own, just steal from other
Up
Up
Up
Up
Respect the way he try to measure the current of the whole bunch of wires at once.
Mehn that was when i realized it's a hoax.
Load up the generator to its rated load and the flywheel will eventually stop due to larger counter emf and losses on the rotor.
Congratulations sir this is very great invention this country requires people like you pl go ahead and start duplicating and solve the power problems.I have seen such unit in Hyderabad but till date it has not been takem off'.
What is the friction losses value couldn't be zero. Reverse current mechanism from the starter motor,
Start button from the flywheel machine and stop button from distribution panel, we have more doubts in its process. Mechanical losses, electrical and thermal losses are zero? Not possible
It's amazing the money and energy spent on building this monster bogus machine. Who would buy it? Or was this for UA-cam hits?
U maths n physics is wrong so u live n believe this is impossible, u've being lied to all ur life, science isn't completely correct ,get that ,why would the entire world no naking fly weel generater ?? Just to trick people? U guys really have n brain!!
@@AffordBindEquipmentYes, it's because it works!
The amount of energy input to this machine is much higher that the energy output. Bearing friction losses, drive belt loses, windage losses, motor losses, generator losses, gearbox losses, etc. If the machine is really efficient, at best you may get about 60% of the energy out of the generator that you put into the motor.
Not only is this correct, but the stored energy would have to be used within minutes, otherwise it would be completely consumed by the losses above.
@@arthurrichardson3439 true
@@arthurrichardson3439 I am as an engineer! The free energy generator can produce electricity for a few minutes, but the air resistance, the fraction, the gravitational force, these factors act on the free energy generator and finally stops the free energy generator. But if we have ccount for the equation and keep some energy storage in between (I mean a powerful battery) in this way we can get power for long hours
You are right.
It's called the Inertial Increase of Electrical Power. It uses inertia to amplify the torque and as such amplify your power input by the motor. Resistance doesn't matter because the motor overcomes it. The amplification comes from the fact that to stop acceleration of a flywheel you don't need to apply an "equal" force but only opposite. The force can be half if the distance from the center is doubled. This works in reverse if your taking power closer to the center which causes the moving mass (further from the center) to produce an amplification of torque. Atleast that's how I understand it. Research Energy Impulse Secrets and Power Impulse Secrets by kanarev for more information. The impulse probably comes from gravity due to the imbalance flywheel. But by using two imbalance flywheel 180 degrees out of phase to remove vibration problems.
This is just what I need at my ocean front property in arizona!!
what is arizona?
Name place
@@JTNRAO7 a place with no ocean front property. It was sarcasm...
Yes, and then you could power the lights on that bridge you just bought...lol
@@runrau9275well maybe you'd have a bridge but no lights.
First of all please don't mix Kinetic and Electrical energy with spiritual energy 😂😂
Dangerous 😂😂
Excellent 😂😂😂
Gold 🤣
MECHANICAL Energy is like a magic and spiritual.
This is what I dreamed when I was 13 years old child !!!
Same here 😂😂😂😂
Hopefully you are smarter now😅
While you are checking the input consumption with clamp meter not showing any amp because of you have clamped with insulated negative and positive together running wire. The clamp meter will read only a single polarity wire only. Please don't post like this 0 input with high output.
پاگل بنارھا یہ ملباری پوری دنیا کو صرف یوٹیوب چینل کے لیے
پہلے انہوں نے کوشش کی ہوگی فری انرجی بنانے کی
لیکن شاید ناکامی اور پروگرام کے وڑ جانے پر یوٹیوب کو لوٹنے کا پروگرام بنا لیا ہے
Great achievement, keep it up, thanks for sharing
Thank you! Will do!
It's an energy storage device. The utility spins up 2.5 tons of kinetic energy. Then it can supply electrical output from the rotating flywheels. The useful output must be some percentage less than the total input.
Yes, and many companies offer this service in Europe
that's the thermodynamics law. always an energy loss when converting one energy to another.
How do you give the input energy continuously if the generator consumed total stored energy. Again the 15 kw motor will be started right?? . How much electric energy will be generated per hour after subtraction of input motor energy consumption
It's an "energy from the vacuüm-extraction" device. How could a little motor in 20 sec. store such an amount of energy.Think.
@@mohitkoker7441 Lol, maybe , but they make a high RPM and you can only store what you put in.
Wow amazing talent my friend full support your channel from Philippines
Thanks and welcome
One start for how much long run the flywheel, it will stop after few time
It will run as long as you supply power through the hidden cable.
you r correct.
Those who are saying it won't work, it's against the laws of physics, they don't understand how really it works.
The real secrets are not shown here.
The real secrets lies in the windings of alternator.
They take the default coil winding out, and put a new coil winding of high impedance high gauge wire, the property of high impedance coil is that it delays the development of magnetic field when current flows through it.
In electrical engineering we call it rise time and decay time of magnetic field, which is directly proportional to the impedance.
That's why during on load conditions, the alternator coil delays the development of magnetic field and meanwhile the rotor magnet passes by the coil, as a result the coil doesn't repel the approach magnet and doesn't attract the departing magnet, so there's no drag or no lenz resistance, only friction exists and that is overcome by heavy flywheel easily.
It's age old technology but doesn't put to the welfare of society. It's hidden and kept for military applications only in countries where it exists.
And how is a "high impedance, high gauge" wire constructed? Is there some special material is it constructed from? That part doesn't make sense because a higher gauge wire will have a lower impedance. And a lower gauge wire will have a higher impedance.
Is it April 1st?
Similarly velocity force/spring/trigger force like that used for firing a gun bullet can also be used for producing kinetic energy.
Thanks to you freands,, your English is good,,,big love from Africa Kenya
I'm curious to know what he shut off to cause it to stop rotating. Is there a braklng system, it slowed quite rapidly.
He turned the eclectic motor off….
The whole video is a lie. He was driving the flywheels with the motor all the time. He basically turned off the motor driving the flywheel. The electrical load and losses in the system made it stop that quick.
Without load why the AMP IS showing 38 amp. In put motor amp u have tested wrong u have to put it on a single wire not in whole three wire
Hi Mr Roshan
Nice to see the demo appreciate your project
Can you please let me know the cost of your free energy generator for our borewel motor of 15KW
He is using kw,s to run his demo water pump it is joke give the load which you produced
If you buy this you can sell it for scrap 😂
This is very interesting invention.companies should do more reseach to create machine like this one, to produce cheaper electricity to communities. very fascinating.
You said you use EB power only to kick start, and then no power to the primary motor you showed it too I agree..
And the generator was running successfully Good, then you said it is running with the help of some gare box which you invented that's secret OK agree...
Later your assistant switched off a switch and the generator stopped what was that switch from where the power supply came to it which motor was switched off could you explain to me please...
If you don't give me your address I'll come and clarify my doubts
The secret box containing motor only ,my thought, they want to blame us by saying this is gearbox
@@suriyap5643 100%
good job! Excellent idea
Shivam starts it initially with which power source?
If external electric power is connected then how much of energy it consumes?
calculate it...the power input to the motor is for 15 secs...
Very nice ❤
Surely, when the motor is disconnected from the grid supply it is then powered by the generator?
Anyway, a very impressive machine! 👍
Super ❤
Is it possible?
NEVER !
@@mgr3566 so why he build it it time for every part and money
@@tomhankstomhanks2579 he knows dumb people will invest. He is not dumb he is a genius in that sense
bravoo🎉🎉🎉🎉🎉
Could we have the design as well for replication everywhere else?
most will not give you design spec. and you really don't need them, only if you intend to use all the same components they are using.
Le gros probleme c'est que tu semble, comme beaucoup d'autres a cette farce !
You are having 3 phase current shifted 120 degrees. When you combine the current on these wires the net adds up to 0. That is why when you measure input wire it is showing 0 in the meter. Don't defraud people like this
This seems to be impossible. What about the system losses ? I will like to visit and inspect the site shown in the video.
@4:30 the amp meter is showing 0 amps. Well it should because all three phases are being measured at once. Even if it were single phase it would also. But monitor a single conductor (as in power wire) at a time ....then you have a true reading and not till then. 😮
Very impressive, the introduction of gear box & fly wheels made it successfully working. 👍👍👍
Very good actors both utuber n the person explaining 😅
They say, once it is started to full speed, the motor gets disconnected from grid, till this point, what they say is correct, but later they say, the motor is totally disconnected from power supply, which is not correct, because the kinetic energy cannot be created and ultimately the flywheels will slow down and stop, to retain the flywheel RPM, we have to give the power supply from the alternator to the motor, so the chain reaction goes on.
also to stop it he just turned it off with a electrical switch when its driven mechanically
Partly. There is no chain reaction happening here. This machine at the most gives you a stable voltage from the generator fed by a fluctuating power supply fed to the motor.
How does he power his home? I did not see it.
इस मशीन को पहले गती (रनिंग) देना पडता है बाद मे जनरेटर अपनी ऊर्जा (करंट, पावर सप्लाई) देता है ओर बिना पावर सप्लाई से यह मशीन चालू रहती है बडे दो चक्के के आर पी एम के वज से इस मे बडे दो चक्के का खेल है ( गती, आर पी एम, रनिंग समतोल रखना, यह सभी के दिमाख मे नही आता है 100%✔️👌👍😃
E
If you total all the energy created by generator and used by motor plus losses it must match. So no new energy created dear. I am surprised no one is talking about theory of energy!! It cant be created !!
How much energy is lost in the gearbox? This is very similar to the Adams generator which also uses flywheels, 2 1kW motors and a 10kW generator. The 2 small motors are pulsed to maintain the speed of the flywheel once it has reached sufficient momentum to run the generator and runs quietly and for much longer periods of time if this one only runs for 45 minutes.
I really need such a machine...even if it runs for 30 minutes free energy
@@issanyamu8445 What electrons giveth, friction taketh away.
@@AffordBindEquipment what friction taketh away spinning flywheel mass over cometh.
@@rmendes2mendes915 friction always wins. It's the law.
@@AffordBindEquipment it depends on the output load capacity
Flywheel can produce energy for sometime but by the time you connect a big load to it it will stop spinning the motor shaft will get very tight due to the load
Magnetic field of generator is biggest resistance, we need more power to move continuously it. Mechanical advantage is not enough
@@shayarchoksi2566 yup he is faking it. Anyone who had played with simple mini motors in childhood by convecting it to an Led to produce electricity shoud already know this. It's basic physics
Very excellent, thank you ؟
The kinetic energy decreases due to constant slow RPM and then the flywheel stops after some time.
have you tried this?
@@francisappiah8549 nothing run forever without input power. flywheel will stop after some time. friction is on of the culprit loss energy even without output. need hug amount of power to running flywheel.
@@francisappiah8549 a wheel stop spinning after sometimes.
@@francisappiah8549 do you know how many engineers lose their minds due to friction and force resolution ?
i guess almost everyone working in mechanical field hits F&F balance problems at some time🙃
Ye machinery kahan milegi... Please suggest me this kind of machernery market location in India?
I’ve always felt certain about perpetual motion machines. Thanks for your contribution. I am sure once we get past human greed we will have a pleather of wonderful creations that make our life more fun
Sorry Sir. We cant get past Human Greed. Everything we do today is guided by both hunger and greed. These guys are both hungry and greedy, sorry to say so. They are selling a 50Kw machine for US$ 60,125. They call this a Deposit. After you buy, then you will wait for 12 months for the machine to be delivered to you after which you pay them 4.0 Indian Rupees for every unit of power you produce. That is GREED WITHOUT BORDERS. These guys are planning to collect ALL the world resources and store it in their houses. This will not be possible and therefore this is a scam, and may be the machine can not work.
Would you buy this machine to power your house or business or farm?
Fks would always say like that. You keep going. Amazing. Tamilnadu Chennai City.❤
But how the energy losses are recovered to maintain the speed and load . The other person should have asked this question ....
I believe the energy losses are overcome by the stored energy in the flywheel.
Hey I would like to buy this may i know the price of this machine.
Mr. Roshan, please see that you don't confuse electrical energy and total energy. electrical energy can be amplified 15 to 20 folds with low spec machines. don't even need higher weights having flywheels. with regular ebike motors and home made alternators, with sufficient cooling setup, the torque difference between the ebike motors and Alternators can be given and the whole concept just works based on inertia and one more basic idea, that is, the input getting motor's torque to spin at specific rpm should be always greater than the output generating alternator's torque necessity to generate the necessary electrical power. All one need is to know the basic understanding on motors and generators (or alternators) for building this kind of machine.
Exactly. It's not 0% input because input Has to be higher than output. That's why this doesn't work.
Dear Mr.Roshan,
Invite BHEL, Hyderabad or ARAI, Pune to authenticate your claims.
is it different from kamma gear fly wheel technology or same
If the machine is not running on power and flywheels are running alternator with the help of gear box which is generating the power; then how come it can be put off with the help of switch. If switch is provided for alternator to stop producing power, then what is the relationship of alternator with flywheel which leads flywheels to stop
Menurut sy ini blm efektif
Karena menggunakan dunamo penggerak
Bila ingin efektif
Harus gunakan kincir air dimana tidak menggunakan dinamo penggerak melainkan menggunakan air jatuh dari bakpenampungan ( toren air) sehingga kerja dinamo penggerak tdk ada yg ada hanya dinamo mesin air buat mengisi air bak penampung air( toren)sehingga bisa kerja maksimal mesin airnya
Dimana air jatuh mutar kincir air dan masuk bak penampung ( kolam air) lalu disedot airnya buat isi air bak penampung diatas( toren )
In this setup, AC Motor continues getting supply. actually motor switch is bypassed inside. what he is showing by clamp-on current meter is false. this wire is three phase ( 3 core ) wire putting clamp-on current over entire cable will show zero current whether motor getting supply or not ,Impossible, there is nothing called free energy in this world. i wonder why he spending so much money on a false project.
According to my understanding there is no energy is created without spending some form of energy. If you spin a flywheel with an electric motor and stop it after some time the kinetic energy will fade away as factors like the friction of the setup plus the load connected to it. For demonstration you can show the voltage until the fly wheel stops as there is no backup for flywheel to keep it running continuously. You can use a flywheel setup to have non iterupted power supply for communication and runway lights used in airports to overcome the voltage buildup delays of a standby generator.I personally have experience in seeing a 650kVa French made SACM make with fly wheel setup with 3 sec.interruption.This is all about a setup in 1978.
The motor is receiving continuous power supply from the generator after power cut off due to which it slows down after running for 45 minutes.
No load, it will run for long time. With load only for a few minutes. The motor must work in Island mode and sync to supply through a ups. The flywheel supplies will generate some power in the generator aka motor for a few minutes. When another generator is started or mains power restored, the ups will sync and run the motor from the last speed and keep it ready again. This system can be used only where continuous power is required in a factory like ceramic plants, semiconductor fabs etc. Now for other applications, this is a useless applications. An UPS with Lithium battery power can power the plant until standby genset is started. No mechanical wear outs. Regards.
When the flywheel reaches its rotation to its fullest speed then main power supply to the flywheel motor is cut off. But to maintain the rotation of the flywheel certain amount of eternal power is definately required sir. May be certain amount of power which is generated is drawn back to maintain the rotation of the flywheel. ...There is lot of doubts arising in your explanation. The interviewer should have asked this question in technical perception.
the grid power supply is shut off and that is when the generator now becomes the power supply for the drive motor.
When Technically possible, why such Power Generation is not available commercially ?
That's called corporate business
It is called bull s**t
lol, PT Barnum would be proud...........
No he wouldn't. He was clever; these people are idiots.
The world will be stunned one day, when it realises that all along the Creator had always given us clean energy , right under our noses. We have only closed up our minds with the little science we thought we knew. We could and now have free electricity without breaking the law of conservation of energy. It has always been in our Physics , but we were all blind to it. Selah!
Dear good efforts, what is the cost of it, second it is too noisy, try to improve it and reduce its noise.
During mechanical movement there will be an energy loss, how you recover that loss.
Я изобрел трансформатор эфира. Это обычный трансформатор обмотанный синей изолентой. Суть в том что потребляет он 0 Вт, а выдает 1000 Вт, могу дать схему интересующимся
These folks didn't take physics...
ممكن ان تزودني بنتيجة المخطط الدائره الكهربائيه
ارجو تزويدي بالمخطط بالو سمحت
Podría pasarme el diagrama por favor
Is there any chance of it being commercialized. How soon?
"free energy" finally happens when all the energy that was used to get the ore, smelt the ore, cast the flywheels, make the iron for the frame, make the copper wiring, the transformers, gear box, motor....all the energy added up needs to be offset by the energy actually created. And then there is the energy to create the money to buy this huge machine, hire a crane to get it on a truck, transport it to the site and set it up to work. You start this thing with a HUGE deficit of energy and there is major catching up to be done just to break even. So you aren't just "creating" free energy on the spot, you have to make up for all the energy put into actually getting it to work at your site. Only then will you start getting "free" energy, which won't happen. so the only person who came out with free energy is the maker in the form of money.
Can we stop complicating things by trying to pretend you don't understand what they mean. If it's so easy to castigate others why not show us your innovation that really works.
@@kelvinnwosa6885 There is no "innovation" that provides free energy.
What answer do you have to the points I raise?
Gear ratio = free energy 😂😮🤔lol
പുളിച്ച ചിരിയുമായി മുഴുത്ട്ടിപ്പും കൊണ്ട് നിരന്തരം ഇറങ്ങാനുള്ള തൊലിക്കട്ടി ഒത്തിരി അപാരമാണേയ്...
Rubish. Violation of law of conservation of energy
energy ??? do you think electrical energy is same as total energy? study your physics books well before answering.
If you don’t know something then it’s rubbishy?
Using Centre Of Gravity for Rotating purpose and thus it is acting as a generator. Very good concept
If something is success why you call it as bull shit
Man made law.
Thermodynamics never going to sue you.
Instead of criticizing, try to do on your own
Why did you start the machine from two places ?One from the wheel base and the other from the box.
How gearbox runs the generator , we need to replace all the engines that runs generator with this man's gearbox 😅. Law of energy seems to be a myth
the school system was an indoctrination...you couldn't possibly tell me that only Albert Einstein and the rest were the smartest amongst us...
Great, Adani or Relince should be use this Idea for Free Energy…🙏🏻🙏🏻🇮🇳🍃
Fraud
What is the price for this setup
Where is it installed, after seeing I want to buy
Can you please share your location
I want this mechinary
Price for setup
The small motor up top. that 15 hp motor is powering it all
Then what about the law of conservation of energy energy can neither be produced nor destroyed but can be converted from one form to another
how much total cost, how long can run continuely
How is the fry wheel rotated after the starter motor
This will help humanity! Great minds!
who set the law of conservation of energy???
What is the cost of the set up
Total set-up price ?
I am not able to get their contact no for enquiry
How much price i will interested buy this podect
How abaut efficiency between cost and power production,...?
is it free energy a schema plz
I want to buy this product
بكل إحترام . مشروعكم كبير 👍 لكنه غير جدير 👎
هل تعتقد ذالك
لماذا لا توجد ترجمة الى العربية
للتعليقات
فعلة هذا قبلك 🧠 و لكي لا تضيع وقتك⌚إشتغل مثلا على طاقة الشمس أفضل☀️ ( من أي بلد أنت لأنصحك ) 👍
Bravo!
Ooh my god!!!!😮😮😮
He is real life RAJNIKANT
do you have published white paper on this machine? something not quite right. ?
To all the comments, what spins the earth for millions if years?
What is the price of 50 kwt unit
Cool video, 2024 version of "Snake Oil".
a Zero in can only make a zero out.if this would work why are we still building giant wind-wheels and Solar-Modules? Please go to Las Vegas because its a nice Illusion^^