Vielen dank. Quick tip, I flaten them in oven (specially used for plastic and cans, NOT for baking). 450F and interestingly enough, afterwards you can remove paint with steel wool and nail polish remover ;) Just FYI as some ppl are afraid to use pressure cooker))
This is great! I saw something I wanted to make out of soda cans but thought it was too much trouble to get flattened. You not only showed how to do that you made cutting the cat much easier, you added cleaning the ink off, and a special project. So much in one video. Great job. Thank you for sharing you knowledge.
@@LapisCyborg oh wow this was a long time ago. Well I tried to make some little windmills but the aluminum just didn't hold up to So Cal winds. Fun trying though. Thanks for asking
Thanks for these step by step instruction. Your method works efficiently and produces great results. I am going to try this with a sheet of paper or cardboard, on the ink side. Some cans have great colors I want to preserve.
I used baking paper for this job - but you immediately feel that you loose heat - so if you have a paper between the iron and the soda can it takes a little bit longer... have fun
I don't have an iron, but if the maximum temperature is about 450F/220C, maybe one could use an oven. The can section could be placed between two flat pans or cookie sheets with a little weight on top. What do you think?
I like with my adding machine tape you can just run it over the sharp edge of a table. In opposite direction of curl. Curl up. I’d maybe do that first then iron a tiny bit if you want total flat and shiny. I also warped my green cutting matt without thinking and putting a warming tray on it to press flowers. The heat was still near enough it permanently made a bump.
That is one of the best instructables I have seen in a while! I would like to know where you get soda with 7% alcohol in it though. LOL! And the stars are great too!
Hello, I looked at a few videos. I don't know if you already know but you can cut the aluminium sheet with a Cricut machine. 😊 . And make for example leaves from a flower. And attached that together to a beautiful tin flower. The sky is your limit. Thank you for your video's !
@@LeFreak it's really a nice machine. You can do so much with the machine. 🥰...look special for a Cricut machine where you can cut thin tin! Have fun 👋
Hi. TQVM for the teach how :) I need a big sheet of aluminium to cover cabinet door. May I know is there an easy way to join many small pieces of these flatten soda cans pls?
I would just a hot cast iron pan instead, easy faster though paint might burn. I would turn one pan upsidedown on the stove then sandwich the sheet between it and another pan.
Do anyone know how to flatten tinned steel cans (0.2-0.3mm thick)? I was trying hammering it (with wooden hammer), bending over edges, rubbing with wooden block - nothing help, still wavy like a crap. Instructions which I can found show how to deal with thicker and softer material. Cans have specific that if you apply force to bump, sheet clicks and concavity appears at the place of bump. Turn it over - and exactly the same happens :/
I want to flatten a beer can to glue to a wood piece that will be a Christmas ornament - the can has a glued on label on it that I want to keep the label on (its a craft beer can). Can I do this same method just ironing it on the inside so as not to ruin the label? Hope I'm making sense. thank you!
I feel like a good way to get this result en bulk would be placing a baking dish atop a stack of sheets and putting it in the oven on low for a few minutes. great stuff though, definitely helped.
Anyone know if this method also works for flattening the thicker, tin-plated steel sheet one can salvage from food cans? This stuff is quite a bit more rigid and thus is more likely to hold a shape you bend it into, but the sheets still stubbornly cling to some of the can's original curve unless I decide to fold parallel to the corrugations.
Hi! I want to stay creative and cover a plastic bin (that I use as a planter outside) with aluminum cans. That means I need to protect them against the elements… Do you have a recommended product that is not too expensive to put on the cans so they don’t corrode? Please let me know - thanks!
Hi - it is aluminum! It will not corrode...... maybe the color will fade out. Have a look at my other video about the pin wheel. This piece is standing on my balcony for more than two year and nothing happens (slight color change). If you start painting on the aluminum then I would protect the painting. So I just recently made a licence plate for my boat. First I flattened the aluminum sheet and then I put the number on it. Then I sprayed several layers of transparent synthetic resin lacquer (for outdoor use) over it for protection. The aluminum sheets then were glued on the outside of the boat. Maybe that's what you are looking for ..... l I like your idea!
@@LeFreak i've tried it on a bear brand milk can an it worked for a little bit, but the longer you iron it the can will get stained (note : there's no ink printing on the can, they use plastic to wrap and label all of them and it's easy to remove it)
Hello Sir, I am from the Ivory Coast in West Africa. I live in another country called Mauritania. One of my activities is to buy used aluminum cans, plastic cans and bottles with a view to sell them to a Chinese company, which transforms them into various finished products. I want to become like them and like you by making large-scale finished products myself. What advice can you give me to achieve this?
I don't have to live off my soda can experiments. If you want to make a business out of it, you should work customer-oriented. So ask the customer what products he would buy from you and negotiate the quantity and price beforehand. The best thing is to make a few prototypes and use them as showpieces. I hope it works
Tja es geht einfach darum ein Sprache zu nehmen welche von möglichst vielen verstanden wir ... das ist Deutsch nicht .. u dä Dialäkt scho grad gar nid😁
Great Information However You Need Some Suede Or Cut Proof Gloves And Maybe A Heat Resistant Glove or Oven Mitt. Don't Harm Yourself To Show Us A Video Tutorial You Can Purchase These Items Online Ebay, Amazon,Walmart etc. Hope This Helps Thanks And Hope To See More Videos!!!!! Also To Cut The Top Off A Old Fashion Can Opener!!!!! Have A Great Day!!!!!
Wow, for a scientist, you would think that you would have learned that the aluminum is still hot. Even the second time you touched it after removing the iron. YUP, Still HOT! Besides that interesting video.
Vielen dank. Quick tip, I flaten them in oven (specially used for plastic and cans, NOT for baking). 450F and interestingly enough, afterwards you can remove paint with steel wool and nail polish remover ;) Just FYI as some ppl are afraid to use pressure cooker))
This is great! I saw something I wanted to make out of soda cans but thought it was too much trouble to get flattened. You not only showed how to do that you made cutting the cat much easier, you added cleaning the ink off, and a special project. So much in one video. Great job. Thank you for sharing you knowledge.
thank you - that is what the internet is made for!
@Time Enuf What did you make?
@@LapisCyborg oh wow this was a long time ago. Well I tried to make some little windmills but the aluminum just didn't hold up to So Cal winds. Fun trying though. Thanks for asking
Holy moly! We have a Waterloo obsession in my house AND a painting/crafts obsession. This is life changing!
Thank you for this video! I am planning on making some plant labels, and being able to work on nice flat can is such a great help. 😁
This is a well made video. I'm experimenting with the foil used as a patch. The stars are a great idea.
One of the best trick I ever watched. Thanks!
Thanks for these step by step instruction. Your method works efficiently and produces great results. I am going to try this with a sheet of paper or cardboard, on the ink side. Some cans have great colors I want to preserve.
I used baking paper for this job - but you immediately feel that you loose heat - so if you have a paper between the iron and the soda can it takes a little bit longer... have fun
@@LeFreak hey can you make a video on how to re ink from a soda can but not use a slow cooker
I drink to much beer hope I can pay for with these amazing ideas 💡 very talented sir.
I immediately subscribed to your channel! Thank you so much, this was like magic to me😊
man this way way more professional and neat way to cut a can, thanks for sharing! You have my sub sensei!
could i do this by putting sheets between two pans and putting in oven? figure it could work as well... possibly... right?
This is super cool
Thanks for sharing
I'd did this but made aluminum more brittle. I was unable to fold without snapping. Was fine for embossing
for folding watch this video: ua-cam.com/video/D4WYvE6rmsQ/v-deo.html
I don't have an iron, but if the maximum temperature is about 450F/220C, maybe one could use an oven. The can section could be placed between two flat pans or cookie sheets with a little weight on top. What do you think?
There are even videos showing this
Now, you made it behave like you want😂🤣nice video.
I like with my adding machine tape you can just run it over the sharp edge of a table. In opposite direction of curl. Curl up. I’d maybe do that first then iron a tiny bit if you want total flat and shiny. I also warped my green cutting matt without thinking and putting a warming tray on it to press flowers. The heat was still near enough it permanently made a bump.
love it👍🏻
Thank you! Such a simple idea that will make things SO much easier! 👍👍
Thank very much thanks 🙏
I have a clothing press.. that should work!
Holy cow I haven't seen an iron like that in a long time
. ? that ain’t old
@@nadronnocojr this comment is tho
this is life-saving. I don't have an iron so I'm using a cast iron pan which works just as well. Thank you!!!
Cool - so you heat up the empty pan and then hold it over the aluminum sheets?
@@LeFreak yeah, pretty much use it the same as the iron! I also have a cast iron griddle that I rest the aluminum on so it heats on both sides.
That is one of the best instructables I have seen in a while! I would like to know where you get soda with 7% alcohol in it though. LOL! And the stars are great too!
thanx for your feedback - and sorry having use a beer can (smile) ... have drink on me
LOL! No apology necessary. I know you were trying to keep it "G" rated. ; ^) And thanks, I think I will take you up on that.
@@LeFreak Agree with the super clear instructions! Thank you for saving my fingers
LOL
Great, thank you!!!
Love it dude I love it well done and keep up the good work
That's brilliant mate
this vid is just what i needed. thanks!
Will eddy current be generated in aluminium sheets? Need your help for school project. 🥺
I'm not sure what you mean, but aluminum from beverage cans can conduct electricity like copper.
Is it possible to glue them together to make them stronger???
I never tried it - maybe difficult to choose the right glue
Hello,
I looked at a few videos. I don't know if you already know but you can cut the aluminium sheet with a Cricut machine. 😊 . And make for example leaves from a flower. And attached that together to a beautiful tin flower. The sky is your limit. Thank you for your video's !
... thanks for telling me - so far I could resist to buy one, but I think I will some day
@@LeFreak it's really a nice machine. You can do so much with the machine. 🥰...look special for a Cricut machine where you can cut thin tin! Have fun 👋
Absolutely brilliant! Thank you for sharing!❤
Beautiful work. Thank you.
Nice video! Useful and enjoyable!!!
Hi. TQVM for the teach how :) I need a big sheet of aluminium to cover cabinet door. May I know is there an easy way to join many small pieces of these flatten soda cans pls?
Fantastic
I wonder if you can do a stack them with a weight in the oven?
It is possible - you will find Videos on youtube
Thank you
Is this possible to do with a food can to get the ridges out?
No - those tin cans are much too thick it works only with the thin beverage cans - sorry
@@LeFreak Thanks for letting me know!
Wow very good video, best one i have seen on aluminum cans
Thanx
I would just a hot cast iron pan instead, easy faster though paint might burn.
I would turn one pan upsidedown on the stove then sandwich the sheet between it and another pan.
Thank you so much really helped
Wow I love this! Thank you you got a new subscriber!!😊😊😊
thanks - always motivating to get positive feedback
Can I do this on aluminum cookie sheets?
Thanks
Hi, I was wondering if this works with all cans? As I have heard that cans have a plastic lining on the inside. Thanks
The flattening works with soda cans that are made of a very thin aluminum wall - the best is to try - it does not take much time.
For some reason my glass wont cut the can any tips?
Do anyone know how to flatten tinned steel cans (0.2-0.3mm thick)? I was trying hammering it (with wooden hammer), bending over edges, rubbing with wooden block - nothing help, still wavy like a crap. Instructions which I can found show how to deal with thicker and softer material. Cans have specific that if you apply force to bump, sheet clicks and concavity appears at the place of bump. Turn it over - and exactly the same happens :/
Thx! Great tips
Nice, specially the stars 👌
I want to flatten a beer can to glue to a wood piece that will be a Christmas ornament - the can has a glued on label on it that I want to keep the label on (its a craft beer can). Can I do this same method just ironing it on the inside so as not to ruin the label? Hope I'm making sense. thank you!
it depends how heat sensitive the lable is - if it is plastic it will melt
Brilliant, thank you
Great video mate, and exactly what I was seeking 👌
Thank You!
I feel like a good way to get this result en bulk would be placing a baking dish atop a stack of sheets and putting it in the oven on low for a few minutes.
great stuff though, definitely helped.
Good idea, did you try that out? Do let us know of the results dear.
can u weld aluminum
VERY useful, thank you!!!
will this work with brass?
Well done
Anyone know if this method also works for flattening the thicker, tin-plated steel sheet one can salvage from food cans? This stuff is quite a bit more rigid and thus is more likely to hold a shape you bend it into, but the sheets still stubbornly cling to some of the can's original curve unless I decide to fold parallel to the corrugations.
It failed for my ~0.2mm thick can. I was hammering it before however :)
How did you get the can wrapper cut so smooth from the can?
you mean after 0:54 seconds in the video?
Unintentional asmr my friend
Thank you‼️
Hi! I want to stay creative and cover a plastic bin (that I use as a planter outside) with aluminum cans. That means I need to protect them against the elements… Do you have a recommended product that is not too expensive to put on the cans so they don’t corrode? Please let me know - thanks!
Hi - it is aluminum! It will not corrode...... maybe the color will fade out.
Have a look at my other video about the pin wheel. This piece is standing on my balcony for more than two year and nothing happens (slight color change). If you start painting on the aluminum then I would protect the painting. So I just recently made a licence plate for my boat. First I flattened the aluminum sheet and then I put the number on it. Then I sprayed several layers of transparent synthetic resin lacquer (for outdoor use) over it for protection. The aluminum sheets then were glued on the outside of the boat. Maybe that's what you are looking for ..... l I like your idea!
Do you need water for the flattening? 🤔
No - just a regular iron
Really cool, Gonna try this
Thank you so much!! Love your channel
Do I need water in the iron?
Does this work with hard aluminum cans like canned milk, food or anything?
Hi Ezra - no I don't think that it will work. I only tried with soda cans. They have a very thin wall in contrast to food tin cans.
@@LeFreak too late
@@LeFreak i've tried it on a bear brand milk can an it worked for a little bit, but the longer you iron it the can will get stained (note : there's no ink printing on the can, they use plastic to wrap and label all of them and it's easy to remove it)
Thank you for sharing! 🥰
Welcome - I like your video with the blue earings
I do not have a pressure cooker, so I put a can in the oven at 350° F and cooked it for an hour along with dinner. The ink came right off.
Does it make any difference if you pressure cook the can before or after you flatten it?
I have not seen a difference - the flatten ones just do not fit in the pressure cooker no more (smile)
Thank you
Thanks!
You know you could sell them online for crafters or peeps looking for thin blank aluminum sheets.
This is awesome! Thank you!
Great!
*AWESOME SAUCE*
Is there a way to make it so the edges aren’t sharp?
Sandpaper maybe?
Thank you for good video !!!
Con que quitale las tintas ?
No, mira mi otro vídeo sobre cómo quitar la tinta -> ua-cam.com/video/HHWNqxCYMtA/v-deo.html
Very cool.
thanks - was looking at your videos - I do have also some depron wings - happy landing
Very nice! subscribed :)
Soda cans ca substitute to shim stock
love this!!!!!!!!!!!!!!!
👏👍 Thank you so much~❣️
I never knew you could iron tin to make it flat!
Hello Sir, I am from the Ivory Coast in West Africa. I live in another country called Mauritania. One of my activities is to buy used aluminum cans, plastic cans and bottles with a view to sell them to a Chinese company, which transforms them into various finished products. I want to become like them and like you by making large-scale finished products myself. What advice can you give me to achieve this?
I don't have to live off my soda can experiments. If you want to make a business out of it, you should work customer-oriented. So ask the customer what products he would buy from you and negotiate the quantity and price beforehand. The best thing is to make a few prototypes and use them as showpieces. I hope it works
great tip.. iron to flatten it
I say its easier to use a can opener for the bottom and the top, then cut down the middle and flatten it woth this trick
Subscribed!
Thanks a looooooooooooooot
hey thanks - you seem to like it!
I love your voice, nice video.
Thanks
“Soda Can” - beer can
“Old Newspaper” - magazine
“Watch” - clock on an iPad
“Eye- Ron” - iron
Wow you just saved my fingers from me amputating them trying to cut cans and trying to flattening them.
Der Moment, wenn du ihn Englisch sprechen hörst, aber alles an Schrift, auf den Magazinen usw., auf Deutsch ist! ;-)
Tja es geht einfach darum ein Sprache zu nehmen welche von möglichst vielen verstanden wir ... das ist Deutsch nicht .. u dä Dialäkt scho grad gar nid😁
@@LeFreak ach du ich hab mit Englisch kein Problem. Zu mal es ja bei dir auch sehr gut zu verstehen ist.
@@LeFreak Grüße ausm Saaletal 07745
Grüsse vom Zürichsee
Roofing shingles vs recycled aluminum can sheets
They really said there is a how to for everything with this one
Great Information However You Need Some Suede Or Cut Proof Gloves And Maybe A Heat Resistant Glove or Oven Mitt. Don't Harm Yourself To Show Us A Video Tutorial You Can Purchase These Items Online Ebay, Amazon,Walmart etc. Hope This Helps Thanks And Hope To See More Videos!!!!! Also To Cut The Top Off A Old Fashion Can Opener!!!!! Have A Great Day!!!!!
ماده ازله الاحبار
Wow, for a scientist, you would think that you would have learned that the aluminum is still hot. Even the second time you touched it after removing the iron. YUP, Still HOT!
Besides that interesting video.
Hi
Gru is that you
i bet i could use an antique iron from the heat of my wood stove in winter so i'm spending electric bill money to flaten