***A fascinating correction about the flame sensor!*** It turns out that fire, as in literal actual flames, acts something like a diode. This means that the furnace is able to detect flames by putting an AC voltage on the flame sensor and monitoring for a voltage drop. The fire will actually conduct some current to the chassis ground of the furnace! This also allows it to detect if a flame has gone out mid-run. Pretty neat!
Its called flame rectification. Fire acts just like a wire for electricity. If the fire drops off so does the path to ground = gas valve closes and furnace will attempt to re-light after a purge cycle.
Flames and even just really really hot gas has lots of ionized particles. This can be seen from the flame itself . The light produced is the result of ionized participles returning to ground state emitting light. This makes flames very conductive (vs air) and this is often exploited through conduction, capacitance you name it. Boilers usually use thermocouples on the pilot light to power a solenoid. (Which is amazing given how little power is involved) UV flame sensors are also popular and use UV light from the flame to excite a special gas to conduct electricity or some other similar technique that could be solid state or who knows there’s so many ways to do it.......
@@John_Lee_ Yep, since the oil flame produces a lot of visible light and the detection of the change in resistance is easy, the moved to CAD cell (which is Cadmium Sulfide also known as CdS) photo resistors. Prior to that a special thermal switch used in the exhaust (called a stack switch) was used to prove flame.
I am a retired furnace designer and you got everything right except for one thing. The flame sensor is not a thermocouple. Modern furnaces use a property called "flame rectification" to detect a flame. An alternating current is passed through the flame and the ionization of the flame acts like (a rather inefficient) diode. The control circuit board detects this small DC current. Three to ten microamps.
Leonard is right and the nature of the sensor can be problematic when installing. People will assume polarity of your 110 vac line doesn't matter and indeed the motors and and other electrical components don't care if hot and neutral are switched. However, the flame sensor and the electronics in the control board do care and may not register a flame when there is one. I have been called to troubleshoot unit heaters on at least two occasions where this was the core issue. Alas, they were installed by electricians who should have known better, but worse argued with me about changing the wiring and insisting it wouldn't matter until I demonstrated it to be otherwise.
Good do know, thanks. I always have a backup on hand, but will continue to use a scotchbrite pad to clean the old one for as long as I can until it fails too often or completely.
@@lambchopsz Less complicated. Spark ignition requires a high voltage source (usually incorporated into the control card) and needs to be 'gapped' and grounded properly and have a highly insulated wire just like a car's spark plug. An HSI just needs a switch on the control card capable of handling the current flow. Good to have both a spare HSI and flame sensor on hand for your furnace as they WILL fail and it will not be at a convenient time.
I would really like to find an inexpensive detector that would alarm not only at the unit but at multiple locations where it cannot fail to get noticed.
@@MPRiley-rb6lj How many stories is your residence? You should have one on every level of your home. In a single level home, the alarm is likely loud enough to wake you. CO is nefarious, and I understand you're looking for inexpensive options, but if you're a homeowner of a multi story home, I'd really recommend hardwired detectors with an integrated circuit. If your basement alarm detects CO (around 30ppm in my experience) it will send an alarm signal to all detectors on that circuit causing them all to sound in an ear-splitting cacophony that will even have your neighbors knocking on your door.
@@travelinghermit Sadly hardwired is the only option I have found. Odd with everything using wireless now. You could have a gun range in the basement and fail to wake someone on the second floor.
As a child, when we had a ~70% furnace, I had a lot of headaches one winter. When the furnace was replaced, we learned it was really good that our windows leaked.
When I was a kid we had a large woodstove that was about 65% efficient. Even woodstoves are more efficient now but back then we used to go through 10-12 cords of wood every winter. Some converted these to natural gas or propane and I have seen converted woodstoves but we did not as propane cost 5-6 times as much as wood for heating. The stove was also compatible with coal but we didn't use any of that.
@@ysf-psfx Modern woodfire stoves have reburners and are much cleaner than they used to be. The exhaust is white/clear(depending on moisture), though full of carbon dioxide and carbon monoxide. Less smell as well.
@@Bubu567 Its something that people don't know, let alone understand about modern wood stoves or heaters. Not the pellet "wood" stoves, but the ones that burn split logs. Having good insulation is key as well. Its cheap and works great for keeping a base temperature in the home as it has a decent thermal mass. Also when the power goes out you only need a small battery pack to run the blowers and they don't use a lot of power themselves. Seasoned wood that isn't rotten helps as well, it doesn't smell and works great. Electric heating works, but I would rather use the heat pump. The strain on the national grid is awful, having a Resistive load is one thing an inductive load another and a Capacitive load terrible. But that is outside of the scope of the video, Wood burning stoves / heaters are good when designed and maintained well. As we move away from bulk paper products, wood in the form of charcoal could become a decent heating commodity when soaked in a small amount of waste oil to keep the dust down and increase the BTUs. TLDR = Natural gas furnaces not bad, wood burner not awful if properly built and fueled, as well as reliable. Pure electric heating only good for small well insulated spaces with limited ventilation. Just food for thought folks.
I'm laughing at your screen name and I shouldn't. Can I go cuddle a creature that has the ability to store 10 thousand volts in his tiny yellow adorable body?
Sooooo I’d like to personally thank TC. I saw this video and thought, “Huh, I never did get my furnace checked out after we bought our house two years ago.” So I looked at the furnace and saw that it was 22 years old and called someone to give it a checkup. News wasn’t good, fellas. It was dumping 12 ppm CO into our house, which I know isn’t a massive amount, but our state says the tech has to turn the furnace off for safety reasons at 6 ppm. Now my family is cold for the weekend, but we’re not dying! Thanks, TC!
Out of curiosity what state is this? Per OSHA Under 50 ppm Isn’t deadly (usually) for an 8 hour period. 6ppm-20ppm can be standard in an exhaust pipe of a furnace during operation. I know you mentioned 6ppm coming into the house though. It is a very low number considering 400ppm is usually the standard deadly level. ASHRAE, WHO and EPA call for shut down at 9-10ppm per 8 hour period.
@@frankrizzo7351 WHO says no more than 6 ppm for 24 hours. KEEP in mind that CarbonMonoxide is always building in the blood at certain point. That's what makes it such a silent killer, your blood is a sponge for CO, it's literally cleaning the air of CO. It takes longer for the CO to leave your blood than it does for it to enter because it bounds so tightly. This is believe is around 70ppm in the air for most people. I have friend who got slightly sick and brain damage form his furnace putting a small amount of CO into his house hold air, this was over one winter. Probably more than 6 ppm though. But parity with the outside is the goal for your household when it comes to CO. I talked to nurse about CO poisonings. He said you know those people who died from a indoor BBQ for heat had the windows open and plenty of ventilation. Yep, the small amount of CO building up in the blood is what does it. CO is not something to mess around with.
@@frankrizzo7351 Dude said 12ppm into the house, which means his family was exposed to that 12ppm continuously. Much worse, I'd imagine, than 10ppm for 8 hours.
@@riccardoorlando2262 especially since CO hugs the floor. If it was a single story, I can see why the cut off would be lower. Also, GET CO DETECTORS!!!!! And check your fire alarms.....
HVAC technician here. Your explanation and overview was great! However you missed one key safety feature, the rollout switch. This is there to stop operation if positive pressure from the blower motor is entering the heat exchanger through an existing crack. That positive pressure will prevent the draft motor from doing its job and flames will rollout of the heat exchanger. Set to trip if it detects flame!
As an HVACR tech I deeply appreciate this. I wish more people were knowledgeable about how we heat and cool spaces. I think HVAC is the most fascinating trade. It encompasses so many different disciplines (plumbing, electrical, high and low voltage, controls, carpentry if you install, and refrigeration) you can go so deep if you want to but most people don’t even have a basic understanding of how it works.
When I got my job in electronics development, I thought it would be super boring. HVAC is all relays, and switches, right? Hey, turn on the heat. Turn on cool. Turn on vent. I mean, it totally is just relays and safety interlock switches, but it's also so much more than that.
@@phillyphakename1255 it is a lot of relays, switches, and safeties. That’s mainly on residential. That doesn’t include the refrigeration side, and understanding how it works. On the industrial side, though we work with a lot of DC controls, PID systems and PLC controllers. Variable frequency drives. When you get into heavy industrial chillers, etc. you get to deal with a lot of complicated hydronic and calculations. If you live up north, you can work with steam. Down south and do a lot of geothermal. It’s infinitely interesting.
@@HCheatNcool yeah, I've learned a lot about the refrigeration cycle, the weirdness that is psychrometrics, not to mention the interesting parts of modern brushless DC/three phase drives, industrial automation, electronic expansion valves, etc. And with R&D even more so, data loggers, non-standard test rigs, pushing systems to extremes, etc.
I did an engineering internship for a company that designed and built the internals of these things (called "heat modules". A couple extra fun facts: The burners are an interesting design in themselves. There's a small nozzle that shoots a stream of gas into a steel venturi tube, which draws air in at just the right ratio for combustion. The other end has a big hole like you'd expect, but they also have tiny channels sticking out on either side to carry the flame across all the burners during ignition. A thermocouple isn't the only way to detect flame. A very interesting method is by placing a small pointy metal rod in the flame. Because of physics and reasons, when you place a large metal surface area (like the burners) and a small metal surface area (like the pointy rod) within a flame, the flame plasma will conduct a small amount of electricity, but only in one direction. Effectively it acts like a diode and a large resistor in series. So the circuitry will check for that condition. It's actually somewhat more robust than a thermocouple - a thermocouple could get hot for some unrelated reason, but it's very unlikely that a couple pieces of metal begin acting like a diode-resistor without flame present. (Unless, of course, an intern is making a control board testing rig, and they literally put a diode and resistor across the flame sense leads.) There are also some furnaces that, along with a limit switch, have a "rollout" switch. These are thermal switches just outside the flame box that are meant to detect if flame is "rolling out" of the fire box instead of going in the tubes. This could happen in the event that the flue or one of the tubes is blocked - the pressure switch activates as expected, the flame is present as expected, but there's not actually airflow, so there's just flames rolling out into the wiring and everything. Some heat exchanger tubes have dimples, and the ones you show in the video have wrinkle bends. These help disturb ideal laminar flow and mix the gases, allowing the gases to cool uniformly. This sounds simple, but the design actually needs to be somewhat careful - any old baffle or dimple design may introduce eddy currents near the tube wall and cause overcooling and condensation, which will rust out the tube. Condensation can only happen in the final pass of a high efficiency heat exchanger - making the entire exchanger from stainless is not cost effective, so it's only that last pass that's built to withstand it. Up until that point it's exactly the same design as a standard 80%. (Also, that's the only reason why pretty much all low efficiency units are 80% - if you extract any more heat, condensation starts, and the steel tubes will rust out. You kinda covered that in the video, though.)
I recently had to replace the small pointy metal rod (flame sensor) in my furnace and I was wondering what the difference was between that and a thermocouple. Now I know. Interesting info, thanks for posting it.
The diode effect is because the flame is slightly ionized and thus conductive. But, in this case, the ions are flowing with the flame. Therefore, it poses less resistance to the electrons 'going with the flow' then to those going against the flow. This makes it behave like a (very bad) diode. If you apply an AC voltage to the probe, and measure the current, you can therefore measure a slightly assymmetrical current. This tells you an ionized stream of flowing gas is present: A flame! These probes can also be used for spark ignition. Useful in instant water heaters, where you want to ignite fuel immediately and not wait a couple seconds for some hot thing to warm up. You can immediately after sense the flame, no need for the probe to warm up. I think that the pointy shape is rod just to aid spark ignition, and not for the flame detection, but I may be wrong there.
@@marco23p : The point will tend to concentrate the electric charge, thus leading to a higher current flow in all states, aiding both sparking _and_ sensing via the same mechanism.
I have been servicing both 80 and 90 plus efficiency furnaces for 3 years in chilly North Dakota. I have worked with 4 local contractors and a myriad of technicians. NOT A SINGLE ONE has been able to describe some of the design features of these furnaces. You have slain ignorance in as much time as it takes me to service the average call! Thank you for helping me help others!
Forever problem with technology and especially teaching. Staying up to date requires effort that not everybody is willing or able to put in. It results in kids leaving school with outdated stuff and technicians sticking to what they learned ages ago.
Must be a real ND person. I lived through the oil boom and all I heard was "cold" "freezing" "the opposite of hell" "frozen wasteland" and "forsaken ice box" My guess is eastern ND as western is alot of electric heat.
@@J-1410 I'm a technician servicing Minot AFB. All our furnaces run natural gas. The base keeps an emergency store of propane for SHTF situations. Once a quarter, they run propane through the lines which runs too rich for all the furnaces, power vents, etc. That means soot builds up on the flame sensors often (most common cause of furnace calls for us). As far as what I feel about ND winters? I came from New Mexico, Turkey before that, and California before that. I do not dig the winter here lol
@@J-1410 If you mean why store propane as opposed to gas, I can't say. I can say I've never seen natural gas under any kind of long term storage like I have with propane. I don't actually know if storage would be a consideration.
Love the Epcot/Norway guy on your t-shirt, a deep cut and excellent "technology connection" for this subject. For anybody who is curious: the face on his shirt is an oil rig worker depicted in a mural once found within the Maelstrom ride in the Norway pavilion of Disney's Epcot. In 2014 it was replaced with a Frozen themed ride. The mural depicted aspects of Scandinavian history/industry, including fossil fuel exploitation. The man on his shirt is depicted manning equipment on an oil rig. A central figure of the mural, his leonine charisma commanded the respect and awe of all who passed under his gaze.
Maelstrom was deeply weird. Although, my husband and I enjoy following any mention of Norway with a reminder that the "Norwegians have always been drawn to the sea."
"Efficiency of 96%" "Correction it's 95%" How dare you betray us with this fallacy! I'll be getting my unnecessarily precise statistics elsewhere from now on, thank you very much.
The efficiency number only states how much fuel it turns into hot air. Hot air heating itself is very inefficient compared to using water as a conductor to radiate heat (usually through the floor in modern homes), but ducts are much cheaper to install than piping, which made it popular in the U.S. - the land of "cheap" energy. There is a UA-cam channel of a disabled guy struggling with paying his propane bill every year, while elsewhere even poor people living north the 50. latitude manage to keep at least one room warm on a moderate rate (like $30 per month) using radiators fed by a gas powered furnace. The problem starts with the concept of heating just the one room you're in doesn't even exist with central forced air.
Oh yeah. A few years ago you could heat your house with one of the high-end graphics cards. I had to upgrade my PC to a 1000W power supply. I forget which card I had but it had multiple fans on it, and chucked out heat you could make toast on. The most recent graphics cards are a bit disappointing by comparison.
He has such a way with explaining things to make sense. He does make you feel like a child listening but after the video you feel smarter and then the jazz plays!
Well all I can say here is: My old man was one of the most feared furnace fighters in Northern Indiana. In the heat of battle my father wove a tapestry of obscenities that as far as we know is still hanging in space over Lake Michigan.
Grew up in a small town here in Newfoundland, so using wood stoves for home heating is commonplace. Man, when you hear the blower turn on during the winter, it's the best.
@@NotThatGuy_YepThatGuy We have 2 furnaces in the house. One of them is on the 2nd floor where I sleep. Imagine a hall with 3 doors on one wall. It goes, my room, furnace closet, bathroom. So to answer your question, 3 feet from my bedroom. Basically on the other side of my wall.
They're also used in semi trucks, and they just use the same diesel as the engine. It can keep my truck as hot as 85°F (29.4°C) for an entire night when it's below freezing outside, and it uses a small fraction of the fuel it would take to run the engine all night.
29.4 is hotter than most people see as comfortable temp, these days the temp in my house is 29-31 and I run the ac to cool it down, 25-26 is what I say comfartable for sleeping
Yeah I remember the one that was in my Peterbilt, darn thing could roast you out in the middle of Minnesota. All it uses for power is the 12v DC from the battery to power the fan and the ignitor. Once lit, it burns efficiently like a kerosene lamp (essentially the same fuel).
First this channel helps me troubleshoot my dishwasher and consistently get clean dishes out of it and now it tells me how my furnace works which just so happens to be having issues right now, love the content keep it up!
I'm reminded of the time we switched the propane tank on my grandparents' furnace. The fuel pressure was higher than the previous tank which meant while there was combustion going on, excess fuel also got pumped into the furnace and was unable to exhaust fast enough. I woke up with headaches for an entire week (my room was in the basement) until I figured out how to adjust the fuel pressure. If I hadn't learned that, my grandparents' house could have exploded or worse. Which is why furnaces need a fuel pressure regulator. Why my mom and I were at my grandparents' house is beyond the scope of this comment.
flatly I can already tell why and without getting into detail, I am sorry. Someone young shouldnt have to learn how to adjust a gas valve because of circumstance. cheers to not being at that point in time anymore.
Another thing to note regarding carbon monoxide: it’s likely part of why they use induced draft rather than forced draft fans. Having the blower before the tubes would put them at slightly higher pressure than the ambient air pressure, which would mean that any leak in the tubes would expel combustion products into the house’s air supply. With induced draft, the tubes are at a lower pressure relative to ambient air, meaning that a leak there will suck clean air into the tubes and won’t let CO into the ventilation system. Of course, any leak in the PVC exhaust will still contaminate the interior, but there’s less risk since it isn’t subject to the same intense thermal cycling as the fire tubes.
oil furnaces do just that...forced draft. The oil burner pushes air into the combustion chamber, as high pressure oil is sprayed into it with an atomizer nozzle. A spark electrode ignites it the air/fuel mixture.
That's the reason why water boilers do use forced draft, because there's no risk of CO leaking into the domestic air vents. Some even have turbines to recover even more latent energy than just forcing air through, turning them into small-scale turbojet engines.
what I find really interesting is how similar it is to a huge fan space heater. you just have heat from burning in the giant heatpipes, instead of resistive heaters stuck to heatsinks. Both provide instant, forced-air heat. Hydronic (radiator) heating works more like those oil-filled electric heaters... takes ages to get going and then overshoots the temp after the thermostat gets triggered. I have to constantly twiddle the thermostat to effectively reduce its tolerance from ±0.5°C to ±0.25°C (but with the overshoot, it takes the actual room temp range from ±1°C to ±0.5°C).
I found it very interesting because I've never seen a gas furnace before (never seen any household stuff functioning on gas really). Wouldn't have thought that something so simple sounding could actually be so complex.
This is quite fascinating to me because I’m from Iceland and our heating is usually done with hot water, piped into homes from geothermal power plants. It’s a really interesting system, I wonder if you might cover that subject some day! ❤️
Donna Wander Yes, I loved it! He did a series of videos here and they are fantastic, no silly misinformation or nonsense like is so often the case with content about Iceland. Tom Scott is great.
If he makes short series (5 part? :D) about ground source heat and heat pumps he might mention areas with lots of heat near the surface like Iceland and if I am not completely wrong areas near Yellowstone also. I mean that some places you don’t need heat pump to get hot water, just a pump.
This is one of the smartest and most informative channels on UA-cam. I spent some time as an engineer in the Coast Guard, and I enjoy learning about technical systems of all kinds. This, and many others, were great videos!
TFW it's Saturday afternoon, your friends are all married with kids, you're in a robe drinking chocolate milk, and you're watching a video called How Furnaces Work.
Or it’s Sunday morning and you’re sat in bed watching it on an iPad, contemplating going downstairs to use your gas burny cooker to make bacon. While you know your friends have been up since 7am trying to herd their children.
Haha yeah, really this TFW was kind of ambiguous, like half of me was in existential horror, and the other half was elated by the freedom to just chill and watch random technology videos without any responsibility or need for appropriate clothing
Re: negative air pressure Modern homes actually have some thing called a HRV or ERV, they recover energy while ventilating the house which allows the house to be very well sealed. This might be a neat video topic for you ;)
Yeah, these things are slick! They pull fresh air from outside and push air from inside out, but through a heat exchanger to take the ~70F air from inside your house and reclaim some of that heat by warming the -30F degree air from outside first.
I have a condensing boiler in a hot-water-baseboard system. When the HVAC company put it in, they routed the condensate through vinyl tubing into my sump pit. A few months later I found a trickle of water running from under the boiler. They had connected the condensate drain to the vinyl tubing by inserting the ends of a little piece of 1/2" copper pipe; the condensate had eaten through it. It probably wasn't doing my sump pump any good either. (Normally zero groundwater entering the sump.) I replaced the copper piece with PVC, and made a big "U" of 3" PVC in the sump pit, one side an inch lower than the other, filled to the top with marble chips; the condensate drips into the high side, so the water has to pass through several feet of marble before it can escape out the low side. Copper pipe fittings nestled in the rocks on each side for a year showed significant corrosion on the inlet side, and none at all on the outlet side; five years later, the condensate had dissolved about 3" of marble from the inlet side, while the outlet was still full & clean. Seems like it's working. 😁
That corrosive water is no joke. I've had a tech warn me that I need to make sure drain water from this stuff goes directly into the nearby drain and doesn't drop onto the concrete floor, because it'll damage the concrete.
DaddyBeanDaddyBean The marble chip method is actually an approved way of disposing of condensate in the UK building regulations. Ordinarily, condensate is routed to a drain where it is diluted by other waste water. It is however acceptable if there is no suitable drain to connect to a soakaway located a suitable distance from the wall / foundation and backfilled with limestone.
Data point: In the northern half of Maine where I live, we don't have a natural gas pipeline network, so most of us are burning No. 2 fuel oil delivered by truck, either in forced air systems or, as in my 100-year-old house, boiler-radiator systems. A few avant-garde types (like my father) are using propane out of cylinders instead, like you, and of course there are the holdouts who still burn wood, and those pellet stove wackos, but fuel oil is still by far the most common choice in these parts. Hot water systems are still pretty common as well, although that's at least partly because central air is pretty uncommon in private homes. It's only hot enough to need AC for about six weeks a year, anyway.
I am one of those pellet stove wackos. It's my primary heat source with a heat pump system as a supplement. I live in Northeastern PA, so not exactly warm. I wouldn't go back. Pellet stoves are efficient and cost effective. (I'm only a convert within the past 3 years, from an oil fired boiler) I will never go back!
Here in Nova Scotia, truck-delivered fuel oil is the predominant fuel source as well. I'm glad I have electric + heat pumps since it means I don't have to worry about tank condition or CO.
@@PCPSolutions You are close to the Anthracite deposits, converting to coal (Anthracite) is going to be cleaner burning and less expensive, but not so renewable.
I'm in Quebec, which is kind of Saudi Arabia for electricity... the default/cheaper way houses are built is to use resistive baseboards here. The only reason this is done is because the equipment is cheaper to buy and install. I have one of those 100 year old houses with hot water radiators. Replaced the fuel oil burner with an electric boiler a couple of years ago. It's comfortable, but need a completely separate system for cooling, and there is no air exchange.
I have a wood stove at home... It's the cheapest variant and it makes no sence to have central heating for a house this small. It is probalby the most common method here. Other folks round here normally have boilers with radiators if the house is on the older side, all fueld by oil bought at the gas station, or, if the house is newer, they heat themselves via AC if they have enough money to pay that electric bill
When you interjected with the "this is a correction" I, admittedly foolishly, expected you to say something like "I misinterpreted the number" or "I suggested a thing that was a positive is actually a negative!" but it was a simple change of 96 to 95 (which is still an A!). That's dedication to truth right there, even if it wasn't necessary or even really disputable, and it is to be commended. (I say "admittedly foolishly" because if it was actually misinformation it would never have made it into the video in the first place, thanks to your keen editing and the production value of these videos.)
As a firefighter we get called on so many smoke/fire investigations for residential structures that utilize these devices to heat their home. As shown in this video they are wonderfully crafted and designed in order to not be the very reason your home burns down but they can only do so much. Save the money needed to maintain and repair these routinely. The cost of an HVAC appointment is pennies on the millions in comparison to the potential loss of life suffered from lazy or forgotten responsibilities. Be safe and that you for your awesome videos my man! Your are a treasure!
I have literally never heard of a forced air gas furnace causing a house fire, how would that even happen? They're metal boxes with a regulated gas supply. As he said about 20 times the biggest risk by far is releasing exhaust into the house, which is also very rare. Their most common risk is failing to work due to open circuit from the safety devices. They aren't going to cause a house fire.
@@tech99070 I'm not a firefighter nor an HVAC guy, but if I had to wager I'd say electrical stuff, bypassed sensors, or bad gas pipes/valves. I've personally seen more than a handful of really disgusting and thick aluminium to copper connections that just send shivers down my spine, as well as bypassed sensors. Not so much about gas pipes other than solid copper ones which are "okay" I guess, since their usability depend entirely on the type of natural gas you get so as to not form flakes of whatever chemical stuff it is that happens with copper pipes and certain types of natural gas.
"Fun" story. At one of my previous jobs we were all given low level carbon monoxide poisoning. According to our maintenance guy, the heat exchangers had cracks big enough you could slip your hand into them. A "lack of funds" meant that they system hadn't been inspected in quite some time. When the carbon monoxide alarms went off, one of our managers told people to get back to work and that it was a "false alarm". Yeah, no. Pretty much everyone ignored him, thankfully, and evacuated. When the fire department arrived we were told it wasn't safe to be in the building.
@@regular-joe You'll be surprised (or maybe not) to learn that absolutely nothing happened to him, and as far as I know he's still there to this day. He was upper management (number 3 in the company basically), so there wasn't much that was going to happen realistically. I suspect COVID has put a MASSIVE damper on their sales though. I can't imagine they're doing well these days.
It doesn't really require much funds to check for cracked heat exchangers. I've been doing HVAC, plumbing, and electrical for years. It always seems heat exchangers get people confused. If there is a crack in a tube, the blower will blow air through it. An idiot can stick a grill lighter in a tube and turn the fan on. If the flame persists there is no crack. If the flame dies there is a crack.
@@megafarad4933 Dunno, that was just the story we were given. That said, I'd believe it. They were crazy penny pinchers. For instance, the owner used to refuse to use curb side check-in at the airport because you were expected to tip, and he felt like that was an exorbitant expense.
Our water heater exhausts became clogged when I was in highschool. There was about a week where everyone in the house felt like death. Finally, when my dad almost didn’t wake up in the morning we had someone come out and check our systems. The HVAC guy brought a sensor in and literally exclaimed upon going downstairs “you all should be dead”, and opened every window he could find before even starting to fix the issue.
Yep, dangerous stuff -- always good to have multiple CO & Gas alarms if you have or use any fuel powered appliances...or even have an attached garage (some have died from push-button-start cars that were accidentally left running in connected garages). We always had 1 on each main floor (basement 20ft from furnace, livingroom 20ft from fireplace, upstairs central to bedrooms) plus an additional one in the room above the garage. I also like to have one indoors where any extension cords come thru windows/doors while running portable emergency generators.
My grandfather has a boiler for radiator heat. He had no ac until about 5 or so years ago. Living in Chicago.... will all those 110°+ heat waves. Being 80+ years old. With a heart condition. Life finds a way!
I'm curious when someone will come up with a two-way radiator system based on heat pipes. Seems like a vacuum-pressure system should be somehow workable.
@@absalomdraconis you mean an air conditioner pointing outwards? heheheheh i think it would be very expensive to run compared to gas, or am i missing something?
I lived in an old home that relied on wood fires for heating. Two for the whole house. I live in the inland northwest and our temps in the winter bottom out at around 10°F with occasional dips into the negatives. Our family converted the fireplaces to natural gas with some odd retrofitting. This video makes me want to really investigate how efficient they are! they've been around for twenty-two years now. When I was a young child I remember being fascinated at having to heat my home with a 19th century wood stove. Thanks to your video on heat pumps my family's home has had a heat pump installed as an addition. And now those gas fireplaces run much less often. And now we have solar panels on them for a completely anachronistic looking home. One look back and our eyes on the future. Love these videos. Thanks for making them!
I had my furnace replaced this year, after the old one wouldn't start due to a cracked heat exchanger - one of the sensors stopped it. The repairman told me a story about family who had a leaky roof and put a blue tarp over the leak - and also unfortunately over their heating vent! After they started getting very sick, they realized what was happening before it was too late. And after hearing this story, I went out and purchased a carbon monoxide detector to go with the new furnace! Thanks for the very educational video...
@ebulating The combustion is always going to produce some amount of CO though. You really need that sensor to be in the living space, away from the flame. Then, if it's going off, you know you have an actual hazard.
@@liesdamnlies3372 Putting it in the return air duct would take care of that. If you have so much CO in the air going to/from your living space that it's tripping a CO alarm (which actually requires quite a lot of CO to trip) then you have way more CO than is safe.
It's so nice living in Iceland, where we get geothermal water out of the ground to heat our houses, provide hot water from faucets and even to heat up driveways and sidewalks when it's below freezing... and it's dirt cheap.... actually, so is our electricity, since that is either hydro or geothermal too
@@Adam-qs5ir Geothermal heating only costs as much as the installation and maintenance of the heat pump, but its effectiveness varies from location to location. Recall that Iceland is highly volcanic, and hence there is a very good return on investment with a geothermal heating system. The issue is that in most places, one must dig a long way into the ground (at least 100ft, the deeper the better), so as to escape the variable temperature of the upper layers. This may be different in Iceland.
@@Adam-qs5ir Plus there is the small cost of driving a pump to move the water (though a heat exchanger can also be used, there isn't much point in Iceland).
The flame sensor, as far as I know, actually works by conducting electricity through the flame, not by sensing a chance in temperature as stated at 15:53.
Yes and no. In a high efficient condensing furnace you'll find a flame sensor that uses flame rectification to detect the flame, but in older standing pilot style furnaces you'll find a thermocouple which "senses" the heat by use of a thermocouple that produces a small voltage when heated.
@@schellenbergenator That's true. Should have specified I was talking about the flame sensor highlighted in that particular part of the video. Having looked inside a very similar furnace I knew it was of the flame rectification type.
As a new home owner who's had some real furnace repair and replacement headaches, this video was wonderful in helping me understand what I'm paying for and why my old furnace had to be replaced.
This was extremely fascinating. The last time I learned this much from a Tech Conn video was the part in the Compact Disc series when he discussed how CD's organize data in packets with redundancy and sub channels (not pits and lands representing 1's and 0's like it's easy to think) and are then reorganized by the player in such a quick time.
technology connections: "but it has a bit of an exhausting job ahead of its self" me: * raises eyebrow * technology connections: "... exhausting!" me: * eyes closed smh *
I'd rather live in the middle of nowhere with the giant propane tank, to be honest. Granted, it's probably not as 'convenient' as suburban life, but I'll wager it's a lot more peaceful.
i live 25km outside of sydneys CBD and i have 2 30kg natural gas cylinders on the side of my house for the stove and bbq and heat my water with the power of the sun
I've been in wholesale hvac sales and tech for 35yrs. since I was 19. specifically gas fired furnaces. I live near Boston, MA. you nailed this video perfectly. outstanding.
@@0oShwavyo0 I guess. I moved schools a few times as a kid, and I distinctly remember getting to the part of my education where we started on nouns and verbs, changing school, and the new school had apparently already done that, and I never really got a good grasp on grammar, and I mostly manage well enough to not swallow my pride and go back to cover that >.>
@First name Last name ??? I feel like a lot of army brats switch schools as kids. I’m not bragging that I somehow failed to learn some of the most basic shit kids know, I’m complaining about it.
European home heating uses hot water as intermediate steps. The boilers are a bit different in setup. Outside air connects to the enclosure. Gas is fed via a gas pressure regulator into the fan intake which sucks air from the encloure. The fax mixes gas and air and pushes it into the burner. Th eburner has a fine mesh to prevent the flame traveling back. Ignition is via a spark which also checks ionization. The flame only exists inside the heat exchanger, which often fully surrounds the flame. The flame burns downwards, meaning that only the coolest gases can escape. That is with an alumin(i)um heat exchanger. Stainless steel ones are a bit different.These boilers are really small, delivering heated tap water and water for heating at 35 kilowatts for example in a 55 x 37 x 27 cm package. (22 x 15 x 11 inch). In apartments, they may be installed in a kitchen cabinet even. Here is a service video on one that does hot water for heating and hot tap water: ua-cam.com/video/AogaQXRH1UI/v-deo.html Note that these have a variable speed fan (and pump nowadays) to allow for variable output (and optimum efficiency).
And hot water vs forced air is like night and day. Take it from someone who has lived in both types. If you have a choice, go boiler. Been there, done that. Forced air cannot possibly be as efficient. Or as comfortable to live in.
I was already thinking - the USA's forced air heating is probably designed without such goals for compactness. Aside from the size of the furnace, you've got the ducts that take up a lot of space compared to radiator pipes.
@@benj1008 It's cheaper to install. Much cheaper. Money is the name of the game. And the further north you go, the less you see of it. And for air, you have to add that separately. However, that's also much more efficient than the forced air furnace.
Forced air systems are huge, and LOUD as FUCK. I much preferred radiator heat in Europe. It was dead silent. According to Zillow, there are zero houses in central Ohio with a radiator.
As a Dutch service engineer I work on these systems daily. Altough we have some slight differences, you have explained it very very well. Thank you! Awesome to see something in my industry :) Adressing to the change of heating systems to heat pumps due to climate change, our heaters in the Netherlands are already ready for hydrogen. It’s as simple as changing the gas valve (if they use the gaslines used for natural gas. If your interested in these type changes they are working on, please let me know. I can help you get in touch with manufacturer.
I think Techmoan and Tech Con compete for this... I did once watch a very long video from Techmoan of him unpacking and testing a huge batch of music players, even though I'll never own a single one of them.
Alec's own pinned comment: "Turns out the fire can be a diode!" At least two comments I've read so far posted after: "Actually, the flame can be a diode."
In honour of those people, Alec I have to add my own 2 coins. You may not know this, but if done correctly, fire can actually work like a diode. And so you don't need a thermocouple. It's crazy, I know.
I'm going to assume they either watched and commented before he got the correction up or were watching on mobile or something and just didn't see it. I pretty much always watch on PC, the few times I have used mobile (and looked at the comments) it felt incredibly clunky and I could easily see someone missing a pinned comment.
@@grn1 I would assume they just missed it. I know that happens. I was just trying to make a joke about it :D But yea Alec's comment was at least earlier than all other people's I saw. At least if the time stamp on the comments is to be believed.
@@mojad6137 You can actually breathe water indefinitely, up until you first breathe air. Research is being done to find a way to allow us to return to filling the lungs with liquid for health purposes and for deep diving or space environments.
I had a furnace fail to light (and why does this always happen on a weekend?). It would light, then shutdown within a few seconds. The repair tech asked if I was handy with basic tools (I am), had me open the furnace, remove the thermocouple, and confirm it was mostly black (it was) -- then told me to grab a wire brush and brush off the carbon buildup (I used a Dremel tool) until it looked completely clean/new again. I put it back in and the furnace worked perfectly. The advice he gave me was that ... even before you have a problem with your furnace, buy a spare thermocouple and a spare inducer fan for your furnace because these were the two most likely parts that can fail and leave you without heat. Having them on-hand means you can just swap out the parts and have heat again without making a service call in the middle of the night or on a weekend.
There is no reason to buy a spare inducer motor as they rarely just fail and there is no reason to buy a new flame sensor as they can almost always be cleaned. Now a new furnace ignitor that is a whole bother conversation. Buy an extra one actually buy two because you are likely to break the first one while installing it
The first failure on my 9 year old furnace was the draft inducer (happened earlier this week). I also had a nice crack in the plastic duct behind it and replaced that as well.
This year, I've replaced more gas forced air systems with Geo and air to air heat pumps than ever. I'm doing two 20+ seer variable systems just this week. Even with slightly higher costs on electricity in some places, the overall efficiency is so much higher, like an energy advantage of 3 to 1.
My house, in Ireland, was built for this setup - there was a brief period in the 70s that they were in vogue - but was instead set up with a resistive electric element instead. The running cost of that is likely why a previous owner got it plumbed for our more regular radiator system
Timmity3 there are very very few areas (even geothermal Iceland and hydro Norway barely get there) where resistive electric is cheaper than gas or oil, and there is literally nowhere where resistive electric is cheaper than heat pump electric.
@@JasperJanssen Resistive electric is always more expensive than heat pump in the utility costs - but in installation, they are an order of magnitude cheaper. So if you have an energy-efficient house, or electricity is cheap in your area, installing a heat pump may make no sense, as the return on investment would take a multitude of years.
@@Smok3yR1der I just imagined hot water being sprayed into the rooms. Luckily I learned to not drink while reading comments or I'd need a new monitor and keyboard.
@@williamnichols2067 You can and there are systems like this. It however is not quite as easy because condensation around cold pipes is an issue. Also, you still need an AC to cool the water, so it just adds extra effort when you could just pipe the coolant around instead.
@@williamnichols2067 because during AC the refrigerant is picking up the heat from the air and moving it outside to the condenser where it is vented. Water doesn't behave properly to allow for refrigeration.
A relative had a new furnace like this put in years ago now, like 6 months after it was in in midd winter it was cold in the house. They looked at it could not find issue, called installer said something is messed up with this thing you installed fix it. End up being (what they said was common issue) a bird sat on the vent on the roof, the Co2 made it pass out falling down the chimney. Then somehow the bird made it into the draft inducer stopping it from running. They later had a cap put on the chimney so this does not happen again.
Most furnaces: has all these fancy safety features and lockouts to stop it from working with the covers off My 1978 Lennox furnace: you can operate me with the covers off but don't stick your fingers in here 😂
"Heat pumps... They are indubitably the future of home space heating" Living in a house that have had geothermal heat pumps heating it since 1982, I just gotta say welcome into the future whenever you are ready :)
@@absalomdraconis If you already have central air, you can have a heat pump. The air handler replaces your existing furnace and the refrigerant lines are run just like a typical A/C installation.
@@Lawrence330 : The best systems are geothermal. Unless you have a reasonable amount of easement-free land, you can't realistically install them after the house is built, only before.
@@absalomdraconis The best heat pumps you mean. Gotcha. I mistook your statement to mean that you couldn't easily switch to a heat pump (not specifically GT) after the house was built. Even an air source heat pump is quite efficient in the lower half of the U.S. I'm in coastal VA and have had a heat pump here for a decade. This house is very poorly insulated and ventilated, so I imagine newer/better construction would see a bigger benefit than I do.
Hey, thanks to this video I was able to identify the problem with my water heater and saves like a hundred euros calling a technician for a furnace no longer in production and with the manufacturer out of business
I’m in Australia, we normally have wood fired, central heating or as what my home has is floor heating via running a fluid through tubes under the floor for each room allowing the heat radiate up from the floor. It feels lovely to get out of bed and walk to the toilet on a warm wooden floor at the middle of the night.
Modern mountain homes here (I live in Colorado, USA) have floor heating because there's no need for central A/C if you live in the mountains. It's a cool idea isn't it.
In Finland we use wood, oil or just plain electricity for heating. In north wood is very commonly used. My father has a huge oldschool stone furnace and it takes a lot of wood to warm up, but it stays hot for a long time once warmed up.
In the Missouri Ozarks most of us grew up with wood heat. Alas, the influx of foreigners from Illinois, California, and other communist territory diluted the intelligence quotient so much that most insurance companies refuse to insure houses that heat with solid fuel. The risk of fire from stupidity is just too great.
To clarify, the vast majority of Australia is too hot for any kind of dedicated heating system beyond an electric resistive heater/reverse cycle AC. The comment was referring to the colder/ more southern states and cities.
Gosh I wish I had watched this before I bought my garage furnace last year. Went with traditional instead of high efficiency and I have always wondered if that was the right choice. Just having the PVC exhaust instead of metal roof vent alone would have been worth it. As usual, great video. Very informative.
Getting yourself a heat pump is a much better option than a high efficiency furnace. Unless you live in the very north, your annual cooling season load will be much greater than your heating season.
It's quite spectacular when the heat exchanger of an old furnace goes. The pressure from the large blower pushes the flames back out and flames come shooting out the front of the furnace, which then trips all sorts of safety features and shuts it down. There's sometimes a loud bang when it happens. It's more common than you'd think.
Alec, thank you for all the videos you make. You take the seemingly mundane objects in our lives and reveal how interesting and fascinating they really are! Please, keep doing what you do!
"Buildings constructed before we became addicted to air conditioning." Yep, that describes my parent's house all right. Boiler and radiators, and a 600 gallon oil tank. We had AC installed when we did a remodel soon after moving in, routing those tubes was interesting (but it was managed!).
@@HenryLoenwind this video fascinated me, as over here in England I’ve never come across a forced air heat system before. We only really use the gas boiler/radiator system over here. I have to admit, it does work really well, and as you say, adds to the cost factor. Handy for drying towels too 😂
That "Ok bye" at the end killed me haha, very good video and I'm looking forward for your video with the thermal imaging camera! Also finally someones that understands the upsides of heat pumps, I live in Québec and I want to buy a house and I'm really looking for one with everything already installed.
Heat pumps are pretty useless below a certain outdoor temp. They depend on an aux system below then, and hence become very inefficient. They're terrific in relatively mild climates, but in very cold areas they're not very good.
@@nate8088 I would counter that there are always days in any climate where they're useful. Honestly, if we had been installing reversible air conditioners for the last 2 decades, we all could see reductions in energy costs and emissions. Even in areas like mine where there are plenty of nights where it wouldn't do much at all, there are also plenty of days when it would be more than sufficient. All it would take is an outside air temperature sensor to determine if it's feasible to run the heat pump. If it is, then do that! And if it's too cold, then you switch to the natural gas or other form of heating. There's a lot of people that think of this in a binary sense that a heat pump is only valuable if it can work as your only source of heat and I think this is a very poor way of thinking. Especially since all it takes to turn an air conditioner into a heat pump is a set of reversing valves. If you are gonna have A/C, you might as well make it a heat pump and frankly I'm somewhat amazed this isn't the norm.
In Québec (Where I also live) you're most likely going to find houses with electric baseboards, even in new houses with central AC... Electricity is so cheap here that we can put a giant resistor in each room to heat. It also makes finding a smart thermostat very hard as almost none of them are made for 120/240vac (most baseboards are run from 240 - the wires in the wall should be a different color)
@@TechnologyConnections What looks promising is geothermal heat pumps. It doesn't take much to drill a hole and run a heat exchange pipe a few meters below ground to tap into that constant ground temperature year around, even at a single-family home level of operation.
Jimorian My parents got geothermal in their house and it was a huge process to dig the trench that the pipes would run in. With regards to how efficient it is they are very pleased with it and their electric bill so maybe it’s worth it.
@@Nicholas-f5 I was a little bit a wonder why this was so important to Airbnb. They specifically highlight if no CO alarm is present. It's a little bit unusual because in Europe, where I live, hot water radiators are the most common heating system. That's why I found it unusual to make such a fuzz about the CO alarms. But now I know why.
I can't wait for your video on heat pumps and their challenges! As someone who lives in a municipality that is banning furnaces from new construction I'm very interested in knowing the tradeoffs of that heating system.
17:15 So THAT'S why my fans don't kick on right away! Seriously I always wondered. My bedroom looks on the 2nd floor is right under our furnace in the attic (that's in addition to the 1st floor furnace that's in the basement). Anyway I hear the unit clock on right above my bed, but the vent over there near my door doesn't actually start spitting out air til after about one minute. I was always MAD at the unit but...Now that I know the alternative would be to blast cold air on me...THANKS FOR WAITING, MR. FURNACE!
Fun fact: This is likely on a completely independent system, not part of the ignition sequence. My furnace is outdoors and in summer the direct sunlight gets the heat exchanger hot enough that the blower comes on, even though the main thermostat is turned off.
I used to work environmental combustion and there’s as many way to light a flame as there is to prove it. Usually we’d light using HEI, high energy ignition, basically a neon transformer and a spark plug sometime backed up with a piezo ignition, like BBQ. Other times we use a remote system called an FFG, flame front generator, to shoot fireballs down a pipe which is advantageous in that you can add valves and light multiple pilots. These systems used continuous monitoring and automatic relight sometimes without timeout because safety concerns for flares. As backup backup we’d use projectiles. Basically a giant six gun shooting a magnesium flare down a pipe with a hard block at the end causing them to explode. Another is the fancy industrial model rocket on a wire shooting through the flammable gas along with manual hand crank systems that hold something like a road flare. If all that fails your down to 2 systems the short straw with a handheld igniter, a match or a modified maglite with a 6ft pipe and spark plug, to good old bow and flaming arrows. Yes flaming arrows are an acceptable way to light an emergency flare in an emergency. To prove flames we used thermocouples, flames rods, infrared, and UV. Thermocouples with a simple temperature relay was the simplest. Flame rods are more common in smaller systems and are as described in the pinned comment. The big boys use optical proving from the hotel boiler that has a Honeywell blue cube and a camera that looks for burning natural gas’s light spectrum to many thousands for a UV tuned to Hydrogen specific wavelength since its invisible to the naked eye. Some cameras are mounted opposite like in a boiler but for larger they can be ground mounted pointed at the top of a stack.
Many thanks for this video! Last week [2020 11 03] my 29 year old 80% efficient gas furnace was replaced with a 96% condensing furnace very similar to yours. Your explanations give me a better understanding of what is going on inside this cute new machine - the installer guys were too busy doing their work to give me a detailed technical lecture on modern furnaces. LOL It was indeed expensive, but my gas supplier [Fortis B.C.] is currently offering a double-rebate [$1400] so my net cost will be acceptably low once I receive the rebate check. BTW, my detailed gas bills show that the B.C. carbon tax I pay is roughly equal to the basic cost of the methane itself. All else are charges for GST, PST, storage, transportation, etc.
This was awesome! My furnace broke down yesterday and even though i only listened to this video in the background while cooking dinner, you have given me the confidence to feel fully qualified to attempt to repair it myself using only a blowtorch as a light source.
As a child, I thought adults were saying, "four stare" heating. So, when I was cold, I'd look (sternly) at the register a few times, but alas, nothing happened.
The first models worked kind of like a clapper - stare ON stare OFF, but early adopters found the system too unstable. It could be set OFF with a passing glance. It was Benjamin Franklin who came up with the "double stare" variant, known today as "four stare" as most users do not wear glasses.
They burn with fire. *FIRE!* I easily see young PPL be afraid of these with fire being the brightest reason behind it. (Pun intended) I am from Sweden and we don't burn with fire to heat our homes. Heat comes from an unknown place by me to heat up water, this heated water is then pumped through multiple radiators strewn about a home, there is about 1 radiator per 2 rooms, if a room is big enough, 2 or more radiators can populate the same room and are almost always located right under a window, but this is a very rough radiator count. Temperature can be altered by twisting a big mechanical dial at 1 of the upper corners of a radiator. Some systems are slow acting, and a temperature-changing twist of a dial takes effect the next day.
@@737Garrus Radiators are trash (at least in America). They don't turn off until it's 90 to 100 degrees in the house and it feels like a heat wave. Plus, the thermostat was in the basement, which is stupid because it's _always_ cold in the basement. Sometimes in unusually-warm days (80 degrees in January), it would still turn on. We had to flip the emergency on/off switch several times just to stop the furnace from heating us to death. Not only that, but most of the radiators didn't work. I shudder to think how warm it would get if _all_ of them came on simultaneously.
"Invest in carbon monoxide alarms and test them regularly. They may just save your life." I absolutely agree _(I say, while sitting in my parents' wooden house that has a gas burning boiler and not even a single smoke alarm)._
Sounds like a great idea for a Christmas present. Last year I got my parents a 2-pack. We now have 4 alarms in our house and it's nice to not have to worry as much about being trapped by a house fire in the middle of the night.
@@thorlancaster5641 They also come as CO/Smoke detectors in one unit now. I have 2 in our house, one in the basement about 10 feet from the furnace next to the stairs, the other on the 1st floor hallway which connects all the bedrooms. And they will wake you up! Even with your ears covered it feels like ice picks going in your ears, it's that loud. Carbon Monoxide is produced when there is in sufficient oxygen to complete combustion, it is a lot harder to get a poorly adjusted burner with gas than say, coal, oil or wood. Once a gas burner is properly set, unless it is somehow damaged, it should give off little to no CO. And with a sealed combustion chamber, it can draw as much air as it needs from outside without creating a vacuum in the house.
@@davidmarquardt2445 as someone who routinely produces smoke near those interconnected smoke detectors (soldering), I can confirm that they feel like icepicks. really wish yanking the batteries disabled them sometimes, I'd like to keep my hearing. at least they're effective!
@some bloke Explaining TDM does not at all get easier with a tube analogy. And it's really easy to understand. Just imagine a sales clerk at a ticket booth/popcorn stand/whatever manning multiple booths. He can only serve one customer at a time, and has to move between lines/queues. While he is serving one line, the customer who has been served has time to gather his things, leave, and the next customer step up to the counter, pull out his wallet and wait for service. If you want to go deeper, just say that he can only spend 60 seconds at each booth before rotating, and then pick up where he left off. If you want to go further still, just add that the people in the line must keep their own time and to make sure that they are ready to be served when their turn is up and have their clock synchronized with the clerk to make sure nobody is talking to dead air. But that's far more nuanced than anyone needs to go. But you're right, it's a fine analogy to a degree, but that man's rant was incoherent and hilarious. "My secretary sent me an Internet, and it took two days to arrive" (not exact quote). It is not a great thought when someone with such an insignificant understanding of technology is creating laws to govern it.
I just bought a house, two years ago, and it had a neglected oil boiler. I got it up and running for the first season but only used it for backup heat. I installed an electric water heater and a pellet stove. Pellet stoves have all the same safety devices as a furnace, pretty neat actually. I tore out the boiler and installed electric baseboard heaters, its a small house, for primary heat but usually rely on the pellet stove. Great video!
4:00 Here in Quebec we sometimes use electric heaters for pretty big places. Apartment buildings are notorious for using pretty much only that, so each person pay for its own heating and the building owner have pretty much no maintenance to do. Sure heat pumps are getting more popular especially for bigger buildings, but they need to be helped by an electrical heater because it gets to cold for them to be efficient during the winter. For houses, they often use another type of heating as the main one, but because it’s often wood based , which means it requires human interaction and it’s hard to control, there’s some electric heaters in the house to regulate the temperature and to heat it when you’re not home for a while. EDIT: I’m not saying we don’t burn gas, but it’s pretty much only a thing in bigger cities were burning wood is regulated or just unpractical.
@@231mac And extreme winters. They are less efficient in extremely cold weather, but even in Alaska, they still beat gas in terms of energy efficiency. Unless you live in the arctic, heat pumps are great. (Now granted, the ones that work well in extreme weather are generally more expensive, but that's getting better). Plus, even if it gets too cold for a heat pump on the worst winter days, you can just have a backup heat source and it will still save energy in the long run.
@@Owen_loves_Butters Sorry but nope. HP's are absolutely lousy in 'extreme winters', unless you think anything above 30 is extreme. I owned a Train XL series HP for 15 years and I worked for an HVAC company in the early 2000's. They work great _until_ temps drop past, I would say, 35 degrees. Then the abilities of the heat pump are unable to keep up with the demand and the system switches to heat strips, which are horrible on efficiency. And that's as good as they get, period.
New homeowner with one of these that’s currently on the fritz. What a fantastic video! Crash course in my own furnace system! Would have liked to see a note about condensate pumps as well! We’ve reused this water vapor, but now we have water in the house that we have to get rid of!
***A fascinating correction about the flame sensor!***
It turns out that fire, as in literal actual flames, acts something like a diode. This means that the furnace is able to detect flames by putting an AC voltage on the flame sensor and monitoring for a voltage drop. The fire will actually conduct some current to the chassis ground of the furnace! This also allows it to detect if a flame has gone out mid-run. Pretty neat!
with oil fired furnace they use something called a "cad cell eye"
You could say that the flame represents... current events. huehuehue
Its called flame rectification. Fire acts just like a wire for electricity. If the fire drops off so does the path to ground = gas valve closes and furnace will attempt to re-light after a purge cycle.
Flames and even just really really hot gas has lots of ionized particles. This can be seen from the flame itself . The light produced is the result of ionized participles returning to ground state emitting light. This makes flames very conductive (vs air) and this is often exploited through conduction, capacitance you name it.
Boilers usually use thermocouples on the pilot light to power a solenoid. (Which is amazing given how little power is involved)
UV flame sensors are also popular and use UV light from the flame to excite a special gas to conduct electricity or some other similar technique that could be solid state or who knows there’s so many ways to do it.......
@@John_Lee_ Yep, since the oil flame produces a lot of visible light and the detection of the change in resistance is easy, the moved to CAD cell (which is Cadmium Sulfide also known as CdS) photo resistors. Prior to that a special thermal switch used in the exhaust (called a stack switch) was used to prove flame.
I am a retired furnace designer and you got everything right except for one thing. The flame sensor is not a thermocouple. Modern furnaces use a property called "flame rectification" to detect a flame. An alternating current is passed through the flame and the ionization of the flame acts like (a rather inefficient) diode. The control circuit board detects this small DC current. Three to ten microamps.
Leonard is right and the nature of the sensor can be problematic when installing. People will assume polarity of your 110 vac line doesn't matter and indeed the motors and and other electrical components don't care if hot and neutral are switched. However, the flame sensor and the electronics in the control board do care and may not register a flame when there is one. I have been called to troubleshoot unit heaters on at least two occasions where this was the core issue. Alas, they were installed by electricians who should have known better, but worse argued with me about changing the wiring and insisting it wouldn't matter until I demonstrated it to be otherwise.
Good do know, thanks. I always have a backup on hand, but will continue to use a scotchbrite pad to clean the old one for as long as I can until it fails too often or completely.
Do you know why furnaces use hot surface igniters instead of spark ignition? I've had my own hot surface igniter go bad because of cracks.
@@lambchopsz Less complicated. Spark ignition requires a high voltage source (usually incorporated into the control card) and needs to be 'gapped' and grounded properly and have a highly insulated wire just like a car's spark plug. An HSI just needs a switch on the control card capable of handling the current flow.
Good to have both a spare HSI and flame sensor on hand for your furnace as they WILL fail and it will not be at a convenient time.
@@lambchopsz They're generally more reliable, but mostly cheaper. There's no electronics with the HSI, just a relay.
Every time my CO monitor goes off it gives me a huge headache and makes me tired. Stupid thing!
I would really like to find an inexpensive detector that would alarm not only at the unit but at multiple locations where it cannot fail to get noticed.
@@MPRiley-rb6lj How many stories is your residence? You should have one on every level of your home. In a single level home, the alarm is likely loud enough to wake you. CO is nefarious, and I understand you're looking for inexpensive options, but if you're a homeowner of a multi story home, I'd really recommend hardwired detectors with an integrated circuit.
If your basement alarm detects CO (around 30ppm in my experience) it will send an alarm signal to all detectors on that circuit causing them all to sound in an ear-splitting cacophony that will even have your neighbors knocking on your door.
@@travelinghermit
Sadly hardwired is the only option I have found. Odd with everything using wireless now. You could have a gun range in the basement and fail to wake someone on the second floor.
Just rip the battery out, sleep tight
LOL funny that.
As a child, when we had a ~70% furnace, I had a lot of headaches one winter. When the furnace was replaced, we learned it was really good that our windows leaked.
Jeez
When I was a kid we had a large woodstove that was about 65% efficient. Even woodstoves are more efficient now but back then we used to go through 10-12 cords of wood every winter. Some converted these to natural gas or propane and I have seen converted woodstoves but we did not as propane cost 5-6 times as much as wood for heating. The stove was also compatible with coal but we didn't use any of that.
@@mharris5047 Thank goodness everyone doesn't burn wood for heat. The smoke output is way worse for all of us.
@@ysf-psfx Modern woodfire stoves have reburners and are much cleaner than they used to be. The exhaust is white/clear(depending on moisture), though full of carbon dioxide and carbon monoxide. Less smell as well.
@@Bubu567 Its something that people don't know, let alone understand about modern wood stoves or heaters. Not the pellet "wood" stoves, but the ones that burn split logs. Having good insulation is key as well. Its cheap and works great for keeping a base temperature in the home as it has a decent thermal mass. Also when the power goes out you only need a small battery pack to run the blowers and they don't use a lot of power themselves. Seasoned wood that isn't rotten helps as well, it doesn't smell and works great. Electric heating works, but I would rather use the heat pump. The strain on the national grid is awful, having a Resistive load is one thing an inductive load another and a Capacitive load terrible. But that is outside of the scope of the video, Wood burning stoves / heaters are good when designed and maintained well. As we move away from bulk paper products, wood in the form of charcoal could become a decent heating commodity when soaked in a small amount of waste oil to keep the dust down and increase the BTUs. TLDR = Natural gas furnaces not bad, wood burner not awful if properly built and fueled, as well as reliable. Pure electric heating only good for small well insulated spaces with limited ventilation. Just food for thought folks.
Been a service tech for 16 years now, and I have to say this is the best explanation video about modern furnaces that I've seen on UA-cam.
I'm laughing at your screen name and I shouldn't. Can I go cuddle a creature that has the ability to store 10 thousand volts in his tiny yellow adorable body?
@@wendyokoopa7048 Lemme check my Magic 8 Ball...
@@wendyokoopa7048 You want to paint your cat yellow?
Sooooo I’d like to personally thank TC. I saw this video and thought, “Huh, I never did get my furnace checked out after we bought our house two years ago.” So I looked at the furnace and saw that it was 22 years old and called someone to give it a checkup. News wasn’t good, fellas. It was dumping 12 ppm CO into our house, which I know isn’t a massive amount, but our state says the tech has to turn the furnace off for safety reasons at 6 ppm.
Now my family is cold for the weekend, but we’re not dying!
Thanks, TC!
Out of curiosity what state is this? Per OSHA Under 50 ppm Isn’t deadly (usually) for an 8 hour period. 6ppm-20ppm can be standard in an exhaust pipe of a furnace during operation. I know you mentioned 6ppm coming into the house though. It is a very low number considering 400ppm is usually the standard deadly level. ASHRAE, WHO and EPA call for shut down at 9-10ppm per 8 hour period.
@@frankrizzo7351 WHO says no more than 6 ppm for 24 hours. KEEP in mind that CarbonMonoxide is always building in the blood at certain point. That's what makes it such a silent killer, your blood is a sponge for CO, it's literally cleaning the air of CO. It takes longer for the CO to leave your blood than it does for it to enter because it bounds so tightly. This is believe is around 70ppm in the air for most people. I have friend who got slightly sick and brain damage form his furnace putting a small amount of CO into his house hold air, this was over one winter. Probably more than 6 ppm though. But parity with the outside is the goal for your household when it comes to CO. I talked to nurse about CO poisonings. He said you know those people who died from a indoor BBQ for heat had the windows open and plenty of ventilation. Yep, the small amount of CO building up in the blood is what does it. CO is not something to mess around with.
@@frankrizzo7351 Dude said 12ppm into the house, which means his family was exposed to that 12ppm continuously. Much worse, I'd imagine, than 10ppm for 8 hours.
@@riccardoorlando2262 especially since CO hugs the floor. If it was a single story, I can see why the cut off would be lower.
Also, GET CO DETECTORS!!!!! And check your fire alarms.....
Not dying is cool!
HVAC technician here. Your explanation and overview was great! However you missed one key safety feature, the rollout switch. This is there to stop operation if positive pressure from the blower motor is entering the heat exchanger through an existing crack. That positive pressure will prevent the draft motor from doing its job and flames will rollout of the heat exchanger. Set to trip if it detects flame!
As an HVACR tech I deeply appreciate this. I wish more people were knowledgeable about how we heat and cool spaces. I think HVAC is the most fascinating trade. It encompasses so many different disciplines (plumbing, electrical, high and low voltage, controls, carpentry if you install, and refrigeration) you can go so deep if you want to but most people don’t even have a basic understanding of how it works.
When I got my job in electronics development, I thought it would be super boring. HVAC is all relays, and switches, right? Hey, turn on the heat. Turn on cool. Turn on vent.
I mean, it totally is just relays and safety interlock switches, but it's also so much more than that.
@@phillyphakename1255 it is a lot of relays, switches, and safeties. That’s mainly on residential. That doesn’t include the refrigeration side, and understanding how it works. On the industrial side, though we work with a lot of DC controls, PID systems and PLC controllers. Variable frequency drives. When you get into heavy industrial chillers, etc. you get to deal with a lot of complicated hydronic and calculations. If you live up north, you can work with steam. Down south and do a lot of geothermal. It’s infinitely interesting.
@@HCheatNcool yeah, I've learned a lot about the refrigeration cycle, the weirdness that is psychrometrics, not to mention the interesting parts of modern brushless DC/three phase drives, industrial automation, electronic expansion valves, etc.
And with R&D even more so, data loggers, non-standard test rigs, pushing systems to extremes, etc.
I did an engineering internship for a company that designed and built the internals of these things (called "heat modules". A couple extra fun facts:
The burners are an interesting design in themselves. There's a small nozzle that shoots a stream of gas into a steel venturi tube, which draws air in at just the right ratio for combustion. The other end has a big hole like you'd expect, but they also have tiny channels sticking out on either side to carry the flame across all the burners during ignition.
A thermocouple isn't the only way to detect flame. A very interesting method is by placing a small pointy metal rod in the flame. Because of physics and reasons, when you place a large metal surface area (like the burners) and a small metal surface area (like the pointy rod) within a flame, the flame plasma will conduct a small amount of electricity, but only in one direction. Effectively it acts like a diode and a large resistor in series. So the circuitry will check for that condition. It's actually somewhat more robust than a thermocouple - a thermocouple could get hot for some unrelated reason, but it's very unlikely that a couple pieces of metal begin acting like a diode-resistor without flame present. (Unless, of course, an intern is making a control board testing rig, and they literally put a diode and resistor across the flame sense leads.)
There are also some furnaces that, along with a limit switch, have a "rollout" switch. These are thermal switches just outside the flame box that are meant to detect if flame is "rolling out" of the fire box instead of going in the tubes. This could happen in the event that the flue or one of the tubes is blocked - the pressure switch activates as expected, the flame is present as expected, but there's not actually airflow, so there's just flames rolling out into the wiring and everything.
Some heat exchanger tubes have dimples, and the ones you show in the video have wrinkle bends. These help disturb ideal laminar flow and mix the gases, allowing the gases to cool uniformly. This sounds simple, but the design actually needs to be somewhat careful - any old baffle or dimple design may introduce eddy currents near the tube wall and cause overcooling and condensation, which will rust out the tube. Condensation can only happen in the final pass of a high efficiency heat exchanger - making the entire exchanger from stainless is not cost effective, so it's only that last pass that's built to withstand it. Up until that point it's exactly the same design as a standard 80%. (Also, that's the only reason why pretty much all low efficiency units are 80% - if you extract any more heat, condensation starts, and the steel tubes will rust out. You kinda covered that in the video, though.)
I wonder how Destin would feel about things disturbing ideal laminar flow.
Great extra info. Enjoyed the read.
I recently had to replace the small pointy metal rod (flame sensor) in my furnace and I was wondering what the difference was between that and a thermocouple. Now I know.
Interesting info, thanks for posting it.
The diode effect is because the flame is slightly ionized and thus conductive. But, in this case, the ions are flowing with the flame. Therefore, it poses less resistance to the electrons 'going with the flow' then to those going against the flow. This makes it behave like a (very bad) diode.
If you apply an AC voltage to the probe, and measure the current, you can therefore measure a slightly assymmetrical current. This tells you an ionized stream of flowing gas is present: A flame!
These probes can also be used for spark ignition. Useful in instant water heaters, where you want to ignite fuel immediately and not wait a couple seconds for some hot thing to warm up. You can immediately after sense the flame, no need for the probe to warm up. I think that the pointy shape is rod just to aid spark ignition, and not for the flame detection, but I may be wrong there.
@@marco23p : The point will tend to concentrate the electric charge, thus leading to a higher current flow in all states, aiding both sparking _and_ sensing via the same mechanism.
Only on this channel can you hear a technical soliloquy like "this is the anterior self regulation ignition inducer " followed by "this sparky thing."
And that is why we enjoy this channel so much folks!
The hot igniting surface which becomes hot enough to do igniting was a good one too :)
Anterior crocodile alligator,
I drive a regulation self inducer.
Now we're getting to the burny business!
I have been servicing both 80 and 90 plus efficiency furnaces for 3 years in chilly North Dakota. I have worked with 4 local contractors and a myriad of technicians. NOT A SINGLE ONE has been able to describe some of the design features of these furnaces. You have slain ignorance in as much time as it takes me to service the average call!
Thank you for helping me help others!
Forever problem with technology and especially teaching. Staying up to date requires effort that not everybody is willing or able to put in. It results in kids leaving school with outdated stuff and technicians sticking to what they learned ages ago.
Must be a real ND person.
I lived through the oil boom and all I heard was "cold" "freezing" "the opposite of hell" "frozen wasteland" and "forsaken ice box"
My guess is eastern ND as western is alot of electric heat.
@@J-1410 I'm a technician servicing Minot AFB. All our furnaces run natural gas. The base keeps an emergency store of propane for SHTF situations. Once a quarter, they run propane through the lines which runs too rich for all the furnaces, power vents, etc. That means soot builds up on the flame sensors often (most common cause of furnace calls for us).
As far as what I feel about ND winters? I came from New Mexico, Turkey before that, and California before that. I do not dig the winter here lol
@@travelinghermit what's their logic for running propane? Make sure it works?
@@J-1410 If you mean why store propane as opposed to gas, I can't say. I can say I've never seen natural gas under any kind of long term storage like I have with propane. I don't actually know if storage would be a consideration.
Love the Epcot/Norway guy on your t-shirt, a deep cut and excellent "technology connection" for this subject. For anybody who is curious: the face on his shirt is an oil rig worker depicted in a mural once found within the Maelstrom ride in the Norway pavilion of Disney's Epcot. In 2014 it was replaced with a Frozen themed ride. The mural depicted aspects of Scandinavian history/industry, including fossil fuel exploitation. The man on his shirt is depicted manning equipment on an oil rig. A central figure of the mural, his leonine charisma commanded the respect and awe of all who passed under his gaze.
I thought it was Chuck Norris in a hard hat.
Maelstrom was deeply weird. Although, my husband and I enjoy following any mention of Norway with a reminder that the "Norwegians have always been drawn to the sea."
"Efficiency of 96%"
"Correction it's 95%"
How dare you betray us with this fallacy! I'll be getting my unnecessarily precise statistics elsewhere from now on, thank you very much.
James Anouna it may be .5% less that 95 because the air filter is a little under sized, makes the blower work harder to get the amount of air it needs
😂
Me, reading up on and buying heating for my house: 96? That's shit, are we still in 70s? 97+ or bust.
It's a quarter of those 4% !
The efficiency number only states how much fuel it turns into hot air. Hot air heating itself is very inefficient compared to using water as a conductor to radiate heat (usually through the floor in modern homes), but ducts are much cheaper to install than piping, which made it popular in the U.S. - the land of "cheap" energy.
There is a UA-cam channel of a disabled guy struggling with paying his propane bill every year, while elsewhere even poor people living north the 50. latitude manage to keep at least one room warm on a moderate rate (like $30 per month) using radiators fed by a gas powered furnace. The problem starts with the concept of heating just the one room you're in doesn't even exist with central forced air.
The most high tech space heater is a gaming pc.
Oh yeah. A few years ago you could heat your house with one of the high-end graphics cards. I had to upgrade my PC to a 1000W power supply. I forget which card I had but it had multiple fans on it, and chucked out heat you could make toast on. The most recent graphics cards are a bit disappointing by comparison.
My crappy HP laptop: I'll burn your entire neighborhood
I have found thatAn old MacBook Pro is a very good leg burner
Fr
I acutally use BOINC to get my CPU to 100% so I don't have to turn on the radiator in my bedroom, it works wonders and I contribute to science too xD
This guy is like my Dad explaining things when I was a child. But I’m almost 40.
My own dad explained things a bit more like the father from Calvin & Hobbes. It was fun, but I rather like Alec's style.
He has such a way with explaining things to make sense. He does make you feel like a child listening but after the video you feel smarter and then the jazz plays!
Holy shit, not only are you Tay Zonday but you're almost 40??
Are you the actual TayZonday? Of Chocolate Rain fame? The internet has taught me to expect impersonators...
@@UA-camstopsharingmyrealname It literally takes one click to check his channel
Well all I can say here is:
My old man was one of the most feared furnace fighters in Northern Indiana.
In the heat of battle my father wove a tapestry of obscenities that as far as we know is still hanging in space over Lake Michigan.
Oh fu - -
What a beautifully written comment
@@spEAMerNationThis is a reference to the movie "A Christmas Story"
RIP Jean Shepard
Hearing the draft inducer kick on while you're laying in bed on a cold winter night is one of the most comforting sounds in the world man.
Grew up in a small town here in Newfoundland, so using wood stoves for home heating is commonplace. Man, when you hear the blower turn on during the winter, it's the best.
Where the heck is your bed in relation to your furnace?
@@NotThatGuy_YepThatGuy We have 2 furnaces in the house. One of them is on the 2nd floor where I sleep.
Imagine a hall with 3 doors on one wall.
It goes, my room, furnace closet, bathroom.
So to answer your question, 3 feet from my bedroom. Basically on the other side of my wall.
I have boiler heat. Hearing the pipes creak and click is oddly nice when it's cold.
Sometimes when I sleep in the living room after watching breaking bad or something I can hear the AC spooling up on its routine
They're also used in semi trucks, and they just use the same diesel as the engine. It can keep my truck as hot as 85°F (29.4°C) for an entire night when it's below freezing outside, and it uses a small fraction of the fuel it would take to run the engine all night.
That is fucking cool.
Ooh, neat.
29.4 is hotter than most people see as comfortable temp, these days the temp in my house is 29-31 and I run the ac to cool it down, 25-26 is what I say comfartable for sleeping
Yeah I remember the one that was in my Peterbilt, darn thing could roast you out in the middle of Minnesota. All it uses for power is the 12v DC from the battery to power the fan and the ignitor. Once lit, it burns efficiently like a kerosene lamp (essentially the same fuel).
Bassam salim I can barely sleep over 23. I heat my place to 22 during winter, 18-19 in my living room.
As a Frenchman that sometimes struggles with spoken English ; thank you so much for the subtitles !
First this channel helps me troubleshoot my dishwasher and consistently get clean dishes out of it and now it tells me how my furnace works which just so happens to be having issues right now, love the content keep it up!
I love how nonchalant or deadpan he is when delivering his puns.
Takes a lof of takes to do that 😁
The true way puns should be delivered.
He's very very newhart esque
I loved his U Tube pun
It's the pause and scene cut that really sets off the puns for me.
This channel is the closest I will ever get to a having a degree in something.
you can get a few more degrees if you get one of these :)
@@megazenn22 lol
I hope that degree is in celcius for the sake of sanity
I thought a degree was required to watch this channel
But he never pointed at the things and said which was which :(
You know, I was half expecting him to say "through the magic of buying another one" somewhere in the video.
there should be a cross-over with the lock picking lawyer memes, "through the magic of buying another one of the things Bosnian Bill and I made"
Through the magic of already having two of them
16:29
He does have 2!
Or at least had 2.
How many furnaces does one house need?
@@PaulMansfield "Let's get this heat exchanger out onto a tray..."
I'm reminded of the time we switched the propane tank on my grandparents' furnace. The fuel pressure was higher than the previous tank which meant while there was combustion going on, excess fuel also got pumped into the furnace and was unable to exhaust fast enough. I woke up with headaches for an entire week (my room was in the basement) until I figured out how to adjust the fuel pressure. If I hadn't learned that, my grandparents' house could have exploded or worse. Which is why furnaces need a fuel pressure regulator.
Why my mom and I were at my grandparents' house is beyond the scope of this comment.
what's worse than a exploded house?
@@drogenmuellerable the former residents dying...
flatly I can already tell why and without getting into detail, I am sorry. Someone young shouldnt have to learn how to adjust a gas valve because of circumstance. cheers to not being at that point in time anymore.
Sounds like an interesting backstory we’d like to hear…
Another thing to note regarding carbon monoxide: it’s likely part of why they use induced draft rather than forced draft fans. Having the blower before the tubes would put them at slightly higher pressure than the ambient air pressure, which would mean that any leak in the tubes would expel combustion products into the house’s air supply. With induced draft, the tubes are at a lower pressure relative to ambient air, meaning that a leak there will suck clean air into the tubes and won’t let CO into the ventilation system. Of course, any leak in the PVC exhaust will still contaminate the interior, but there’s less risk since it isn’t subject to the same intense thermal cycling as the fire tubes.
oil furnaces do just that...forced draft. The oil burner pushes air into the combustion chamber, as high pressure oil is sprayed into it with an atomizer nozzle. A spark electrode ignites it the air/fuel mixture.
That's the reason why water boilers do use forced draft, because there's no risk of CO leaking into the domestic air vents. Some even have turbines to recover even more latent energy than just forcing air through, turning them into small-scale turbojet engines.
better that than be dead!
Me, an intellectual,: “Hmmmm”
Also placing the fan after the tubes lengthens its service life and makes it cheaper to produce, because less thermal stress will occur
After seeing this I got rid of the ventless unit ! replaced it with a vented unit .
People take these for granted, but they're actually really interesting pieces of technology.
that's basically the theme of this channel
These topics are my favorite, I hope he continues to make more.
Furnaces are comprehensible pieces of tech which makes them really cool to learn about
what I find really interesting is how similar it is to a huge fan space heater. you just have heat from burning in the giant heatpipes, instead of resistive heaters stuck to heatsinks. Both provide instant, forced-air heat.
Hydronic (radiator) heating works more like those oil-filled electric heaters... takes ages to get going and then overshoots the temp after the thermostat gets triggered. I have to constantly twiddle the thermostat to effectively reduce its tolerance from ±0.5°C to ±0.25°C (but with the overshoot, it takes the actual room temp range from ±1°C to ±0.5°C).
I found it very interesting because I've never seen a gas furnace before (never seen any household stuff functioning on gas really). Wouldn't have thought that something so simple sounding could actually be so complex.
This is quite fascinating to me because I’m from Iceland and our heating is usually done with hot water, piped into homes from geothermal power plants. It’s a really interesting system, I wonder if you might cover that subject some day! ❤️
Tom Scott did a video on that semi-recently.
Donna Wander Yes, I loved it! He did a series of videos here and they are fantastic, no silly misinformation or nonsense like is so often the case with content about Iceland. Tom Scott is great.
If he makes short series (5 part? :D) about ground source heat and heat pumps he might mention areas with lots of heat near the surface like Iceland and if I am not completely wrong areas near Yellowstone also.
I mean that some places you don’t need heat pump to get hot water, just a pump.
Living atop a supervolcano does have its advantages.
@@Karjis Geysers, CA too
This is one of the smartest and most informative channels on UA-cam. I spent some time as an engineer in the Coast Guard, and I enjoy learning about technical systems of all kinds. This, and many others, were great videos!
TFW it's Saturday afternoon, your friends are all married with kids, you're in a robe drinking chocolate milk, and you're watching a video called How Furnaces Work.
Shivan so you really dodged a bullet then, uh?
Or it’s Sunday morning and you’re sat in bed watching it on an iPad, contemplating going downstairs to use your gas burny cooker to make bacon.
While you know your friends have been up since 7am trying to herd their children.
I watched this while setting up a fort for my two kids. Win win.
Haha yeah, really this TFW was kind of ambiguous, like half of me was in existential horror, and the other half was elated by the freedom to just chill and watch random technology videos without any responsibility or need for appropriate clothing
they sell "condensate neutralizers" which is literally a plastic box with a couple chambers full of limestone chips.
Re: negative air pressure
Modern homes actually have some thing called a HRV or ERV, they recover energy while ventilating the house which allows the house to be very well sealed.
This might be a neat video topic for you ;)
Yeah, these things are slick! They pull fresh air from outside and push air from inside out, but through a heat exchanger to take the ~70F air from inside your house and reclaim some of that heat by warming the -30F degree air from outside first.
my windows are older than i am so i do not have to worry about this
Yes please can you do a video on this?! I have one and I have no idea how it works!
I hadn't heard of these! They sound nifty!
What heat pumps?
I have a condensing boiler in a hot-water-baseboard system. When the HVAC company put it in, they routed the condensate through vinyl tubing into my sump pit.
A few months later I found a trickle of water running from under the boiler. They had connected the condensate drain to the vinyl tubing by inserting the ends of a little piece of 1/2" copper pipe; the condensate had eaten through it. It probably wasn't doing my sump pump any good either. (Normally zero groundwater entering the sump.)
I replaced the copper piece with PVC, and made a big "U" of 3" PVC in the sump pit, one side an inch lower than the other, filled to the top with marble chips; the condensate drips into the high side, so the water has to pass through several feet of marble before it can escape out the low side. Copper pipe fittings nestled in the rocks on each side for a year showed significant corrosion on the inlet side, and none at all on the outlet side; five years later, the condensate had dissolved about 3" of marble from the inlet side, while the outlet was still full & clean. Seems like it's working. 😁
That corrosive water is no joke. I've had a tech warn me that I need to make sure drain water from this stuff goes directly into the nearby drain and doesn't drop onto the concrete floor, because it'll damage the concrete.
@@Corrodias having seen firsthand what it does to marble over time, I don't doubt it.
That's genius and kinda scary.
@@DaddyBeanDaddyBean Well marble is metamorphized limestone. You can bake marble to make lime
DaddyBeanDaddyBean The marble chip method is actually an approved way of disposing of condensate in the UK building regulations. Ordinarily, condensate is routed to a drain where it is diluted by other waste water. It is however acceptable if there is no suitable drain to connect to a soakaway located a suitable distance from the wall / foundation and backfilled with limestone.
One more safety feature- the access panel interlock switch, which you likely defeated to get your interior shots.
it's not *essential* since you're unlikely to leave furnace open,but I can see the danger.
Ah yes the vinyl tape holding button, it’s where i keep my vinyl tape
Our furnace just broke, so I suddenly dived into a deep hole of "how furnaces work". This video is very timely.
How did you survive the winter?
@@Jusiun by getting it replaced ...
@@Jusiun Portable heaters
"and what lives on the other side of those tubes are the flamethrowers."
t h e w h a t
Technically called “inshot” burners.
did anyone notice he said "flamefrowers"?
@@gregmercil3968 Flamethrowers sounds way better.
Flamethrowers, it throws flames at whatever you point it at
@@ryank1273 lately, I’ve been calling them “thrusters.” 😆
Data point: In the northern half of Maine where I live, we don't have a natural gas pipeline network, so most of us are burning No. 2 fuel oil delivered by truck, either in forced air systems or, as in my 100-year-old house, boiler-radiator systems. A few avant-garde types (like my father) are using propane out of cylinders instead, like you, and of course there are the holdouts who still burn wood, and those pellet stove wackos, but fuel oil is still by far the most common choice in these parts.
Hot water systems are still pretty common as well, although that's at least partly because central air is pretty uncommon in private homes. It's only hot enough to need AC for about six weeks a year, anyway.
I am one of those pellet stove wackos. It's my primary heat source with a heat pump system as a supplement. I live in Northeastern PA, so not exactly warm. I wouldn't go back. Pellet stoves are efficient and cost effective. (I'm only a convert within the past 3 years, from an oil fired boiler) I will never go back!
Here in Nova Scotia, truck-delivered fuel oil is the predominant fuel source as well. I'm glad I have electric + heat pumps since it means I don't have to worry about tank condition or CO.
@@PCPSolutions You are close to the Anthracite deposits, converting to coal (Anthracite) is going to be cleaner burning and less expensive, but not so renewable.
I'm in Quebec, which is kind of Saudi Arabia for electricity... the default/cheaper way houses are built is to use resistive baseboards here. The only reason this is done is because the equipment is cheaper to buy and install. I have one of those 100 year old houses with hot water radiators. Replaced the fuel oil burner with an electric boiler a couple of years ago. It's comfortable, but need a completely separate system for cooling, and there is no air exchange.
I have a wood stove at home... It's the cheapest variant and it makes no sence to have central heating for a house this small. It is probalby the most common method here. Other folks round here normally have boilers with radiators if the house is on the older side, all fueld by oil bought at the gas station, or, if the house is newer, they heat themselves via AC if they have enough money to pay that electric bill
When you interjected with the "this is a correction" I, admittedly foolishly, expected you to say something like "I misinterpreted the number" or "I suggested a thing that was a positive is actually a negative!" but it was a simple change of 96 to 95 (which is still an A!).
That's dedication to truth right there, even if it wasn't necessary or even really disputable, and it is to be commended.
(I say "admittedly foolishly" because if it was actually misinformation it would never have made it into the video in the first place, thanks to your keen editing and the production value of these videos.)
"But I digress..." I think most of us like your digressions!
As a firefighter we get called on so many smoke/fire investigations for residential structures that utilize these devices to heat their home. As shown in this video they are wonderfully crafted and designed in order to not be the very reason your home burns down but they can only do so much. Save the money needed to maintain and repair these routinely. The cost of an HVAC appointment is pennies on the millions in comparison to the potential loss of life suffered from lazy or forgotten responsibilities.
Be safe and that you for your awesome videos my man! Your are a treasure!
I have literally never heard of a forced air gas furnace causing a house fire, how would that even happen? They're metal boxes with a regulated gas supply. As he said about 20 times the biggest risk by far is releasing exhaust into the house, which is also very rare. Their most common risk is failing to work due to open circuit from the safety devices. They aren't going to cause a house fire.
You forget that at the end of the day all of these safety features are still being built by the lowest bidders.
@@tech99070 A bad rollout or gas leak could lead to a larger fire.
@@tech99070 I'm not a firefighter nor an HVAC guy, but if I had to wager I'd say electrical stuff, bypassed sensors, or bad gas pipes/valves. I've personally seen more than a handful of really disgusting and thick aluminium to copper connections that just send shivers down my spine, as well as bypassed sensors. Not so much about gas pipes other than solid copper ones which are "okay" I guess, since their usability depend entirely on the type of natural gas you get so as to not form flakes of whatever chemical stuff it is that happens with copper pipes and certain types of natural gas.
@@Coconut-219 They are only built by the lowest bidder if you are buying the lowest cost furnace. Buy midgrade.
"Fun" story. At one of my previous jobs we were all given low level carbon monoxide poisoning. According to our maintenance guy, the heat exchangers had cracks big enough you could slip your hand into them. A "lack of funds" meant that they system hadn't been inspected in quite some time. When the carbon monoxide alarms went off, one of our managers told people to get back to work and that it was a "false alarm". Yeah, no. Pretty much everyone ignored him, thankfully, and evacuated. When the fire department arrived we were told it wasn't safe to be in the building.
But I vengefully want to know what happened to that manager (and company)!!!
@@regular-joe You'll be surprised (or maybe not) to learn that absolutely nothing happened to him, and as far as I know he's still there to this day. He was upper management (number 3 in the company basically), so there wasn't much that was going to happen realistically. I suspect COVID has put a MASSIVE damper on their sales though. I can't imagine they're doing well these days.
@@IanDunbar1 Ideally he should have been arrested for what he did. Was it a company so big that they effectively owned the police, Capone style?
It doesn't really require much funds to check for cracked heat exchangers. I've been doing HVAC, plumbing, and electrical for years. It always seems heat exchangers get people confused. If there is a crack in a tube, the blower will blow air through it. An idiot can stick a grill lighter in a tube and turn the fan on. If the flame persists there is no crack. If the flame dies there is a crack.
@@megafarad4933 Dunno, that was just the story we were given. That said, I'd believe it. They were crazy penny pinchers. For instance, the owner used to refuse to use curb side check-in at the airport because you were expected to tip, and he felt like that was an exorbitant expense.
I've never been so excited anticipating a future video about heat pumps.
Our water heater exhausts became clogged when I was in highschool. There was about a week where everyone in the house felt like death. Finally, when my dad almost didn’t wake up in the morning we had someone come out and check our systems. The HVAC guy brought a sensor in and literally exclaimed upon going downstairs “you all should be dead”, and opened every window he could find before even starting to fix the issue.
Yep, dangerous stuff -- always good to have multiple CO & Gas alarms if you have or use any fuel powered appliances...or even have an attached garage (some have died from push-button-start cars that were accidentally left running in connected garages). We always had 1 on each main floor (basement 20ft from furnace, livingroom 20ft from fireplace, upstairs central to bedrooms) plus an additional one in the room above the garage. I also like to have one indoors where any extension cords come thru windows/doors while running portable emergency generators.
Y'all got super lucky, that's scary AF.
@@matthewmiller6068 like I needed another reason to hate pushbutton start...
My grandfather has a boiler for radiator heat. He had no ac until about 5 or so years ago. Living in Chicago.... will all those 110°+ heat waves. Being 80+ years old. With a heart condition. Life finds a way!
I'm curious when someone will come up with a two-way radiator system based on heat pipes. Seems like a vacuum-pressure system should be somehow workable.
@@absalomdraconis
you mean an air conditioner pointing outwards? heheheheh
i think it would be very expensive to run compared to gas, or am i missing something?
Me: Lives in the cold north and knows full well how furnaces work
Also me: watches the entire video anyways and enjoys it
same bro
Me: In Australia, the reverse works fine here.
Thats ok I'm a licensed hvac tradesmen and I sat here and watched it
I worked for an HVAC company for 4 years and still watched to the end.
I lived in an old home that relied on wood fires for heating. Two for the whole house. I live in the inland northwest and our temps in the winter bottom out at around 10°F with occasional dips into the negatives. Our family converted the fireplaces to natural gas with some odd retrofitting. This video makes me want to really investigate how efficient they are! they've been around for twenty-two years now. When I was a young child I remember being fascinated at having to heat my home with a 19th century wood stove. Thanks to your video on heat pumps my family's home has had a heat pump installed as an addition. And now those gas fireplaces run much less often. And now we have solar panels on them for a completely anachronistic looking home.
One look back and our eyes on the future.
Love these videos. Thanks for making them!
I had my furnace replaced this year, after the old one wouldn't start due to a cracked heat exchanger - one of the sensors stopped it. The repairman told me a story about family who had a leaky roof and put a blue tarp over the leak - and also unfortunately over their heating vent! After they started getting very sick, they realized what was happening before it was too late. And after hearing this story, I went out and purchased a carbon monoxide detector to go with the new furnace! Thanks for the very educational video...
@ebulating The combustion is always going to produce some amount of CO though. You really need that sensor to be in the living space, away from the flame. Then, if it's going off, you know you have an actual hazard.
I'm living in blue roof territory (sw Louisiana) right now and I'm seeing a lot of houses that have their vents covered...
@@liesdamnlies3372 Putting it in the return air duct would take care of that. If you have so much CO in the air going to/from your living space that it's tripping a CO alarm (which actually requires quite a lot of CO to trip) then you have way more CO than is safe.
@@uzlonewolf Fair point.
It's so nice living in Iceland, where we get geothermal water out of the ground to heat our houses, provide hot water from faucets and even to heat up driveways and sidewalks when it's below freezing... and it's dirt cheap.... actually, so is our electricity, since that is either hydro or geothermal too
My natural gas costs me no more than 75 us dollars (or 10,429 Krona) a month throughout the winter. What does geothermal heating cost? Just curious.
@@Adam-qs5ir Geothermal heating only costs as much as the installation and maintenance of the heat pump, but its effectiveness varies from location to location. Recall that Iceland is highly volcanic, and hence there is a very good return on investment with a geothermal heating system. The issue is that in most places, one must dig a long way into the ground (at least 100ft, the deeper the better), so as to escape the variable temperature of the upper layers. This may be different in Iceland.
@@Jupiter__001_ makes sense, drilling that deep probably costs a fair amount.
@@Adam-qs5ir Plus there is the small cost of driving a pump to move the water (though a heat exchanger can also be used, there isn't much point in Iceland).
@Mark Kennedy that's hard work, but I'd enjoy it
The flame sensor, as far as I know, actually works by conducting electricity through the flame, not by sensing a chance in temperature as stated at 15:53.
Yes and no. In a high efficient condensing furnace you'll find a flame sensor that uses flame rectification to detect the flame, but in older standing pilot style furnaces you'll find a thermocouple which "senses" the heat by use of a thermocouple that produces a small voltage when heated.
tech conn pinned a comment on this point. Electricity is weird!
@@schellenbergenator That's true. Should have specified I was talking about the flame sensor highlighted in that particular part of the video. Having looked inside a very similar furnace I knew it was of the flame rectification type.
As a new home owner who's had some real furnace repair and replacement headaches, this video was wonderful in helping me understand what I'm paying for and why my old furnace had to be replaced.
This was extremely fascinating. The last time I learned this much from a Tech Conn video was the part in the Compact Disc series when he discussed how CD's organize data in packets with redundancy and sub channels (not pits and lands representing 1's and 0's like it's easy to think) and are then reorganized by the player in such a quick time.
technology connections: "but it has a bit of an exhausting job ahead of its self"
me: * raises eyebrow *
technology connections: "... exhausting!"
me: * eyes closed smh *
"I'm really in the middle of nowhere." Rural folks with giant propane tanks, can confirm.
I'd rather live in the middle of nowhere with the giant propane tank, to be honest. Granted, it's probably not as 'convenient' as suburban life, but I'll wager it's a lot more peaceful.
i live 25km outside of sydneys CBD and i have 2 30kg natural gas cylinders on the side of my house for the stove and bbq and heat my water with the power of the sun
@@Slippergypsy Sounds like a righteous setup, friend.
@@Slippergypsy In America, 500 gallon tanks are relatively common for residences! Around 770 kg!
@@xaenon Agreed.
I've been in wholesale hvac sales and tech for 35yrs. since I was 19. specifically gas fired furnaces. I live near Boston, MA. you nailed this video perfectly. outstanding.
Any idea how to make one of these things quieter?
I live for the “[adjective]ly smooth jazz line” at the end of each episode.
Orange. Metallic. Hairy. Loquacious. Moist. Greasy. Speckled. Bright.
Adverb tho?
@@0oShwavyo0 I guess. I moved schools a few times as a kid, and I distinctly remember getting to the part of my education where we started on nouns and verbs, changing school, and the new school had apparently already done that, and I never really got a good grasp on grammar, and I mostly manage well enough to not swallow my pride and go back to cover that >.>
@First name Last name ??? I feel like a lot of army brats switch schools as kids. I’m not bragging that I somehow failed to learn some of the most basic shit kids know, I’m complaining about it.
@@theGhostWolfe It is never too late to learn :)
I definitely exhaled harder than usual at "you might call them U-tubes."
"exhausting job" is what did it for me, haha...
I saw it coming when he said about series of tubes!
I know, it was like one right after the other for a good minute, there.
European home heating uses hot water as intermediate steps.
The boilers are a bit different in setup. Outside air connects to the enclosure. Gas is fed via a gas pressure regulator into the fan intake which sucks air from the encloure. The fax mixes gas and air and pushes it into the burner.
Th eburner has a fine mesh to prevent the flame traveling back.
Ignition is via a spark which also checks ionization.
The flame only exists inside the heat exchanger, which often fully surrounds the flame.
The flame burns downwards, meaning that only the coolest gases can escape.
That is with an alumin(i)um heat exchanger. Stainless steel ones are a bit different.These boilers are really small, delivering heated tap water and water for heating at 35 kilowatts for example in a 55 x 37 x 27 cm package.
(22 x 15 x 11 inch). In apartments, they may be installed in a kitchen cabinet even.
Here is a service video on one that does hot water for heating and hot tap water: ua-cam.com/video/AogaQXRH1UI/v-deo.html
Note that these have a variable speed fan (and pump nowadays) to allow for variable output (and optimum efficiency).
And hot water vs forced air is like night and day. Take it from someone who has lived in both types. If you have a choice, go boiler. Been there, done that. Forced air cannot possibly be as efficient. Or as comfortable to live in.
I was already thinking - the USA's forced air heating is probably designed without such goals for compactness. Aside from the size of the furnace, you've got the ducts that take up a lot of space compared to radiator pipes.
@@benj1008 It's cheaper to install. Much cheaper. Money is the name of the game. And the further north you go, the less you see of it. And for air, you have to add that separately. However, that's also much more efficient than the forced air furnace.
Most houses I know burn heating oil (mazout) instead of gas, is that even a thing in the US?
Forced air systems are huge, and LOUD as FUCK. I much preferred radiator heat in Europe. It was dead silent. According to Zillow, there are zero houses in central Ohio with a radiator.
As a Dutch service engineer I work on these systems daily. Altough we have some slight differences, you have explained it very very well. Thank you! Awesome to see something in my industry :)
Adressing to the change of heating systems to heat pumps due to climate change, our heaters in the Netherlands are already ready for hydrogen. It’s as simple as changing the gas valve (if they use the gaslines used for natural gas.
If your interested in these type changes they are working on, please let me know. I can help you get in touch with manufacturer.
Only Technology Connections can hold my attention for this long on this sort of topic.
I think Techmoan and Tech Con compete for this... I did once watch a very long video from Techmoan of him unpacking and testing a huge batch of music players, even though I'll never own a single one of them.
Most definitely 👍
Alec's own pinned comment:
"Turns out the fire can be a diode!"
At least two comments I've read so far posted after:
"Actually, the flame can be a diode."
In honour of those people, Alec I have to add my own 2 coins.
You may not know this, but if done correctly, fire can actually work like a diode. And so you don't need a thermocouple. It's crazy, I know.
I'm going to assume they either watched and commented before he got the correction up or were watching on mobile or something and just didn't see it. I pretty much always watch on PC, the few times I have used mobile (and looked at the comments) it felt incredibly clunky and I could easily see someone missing a pinned comment.
@@grn1 I would assume they just missed it. I know that happens. I was just trying to make a joke about it :D
But yea Alec's comment was at least earlier than all other people's I saw.
At least if the time stamp on the comments is to be believed.
A diode can also create a flame with enough current. Well, once, anyway.
@@mojad6137 You can actually breathe water indefinitely, up until you first breathe air. Research is being done to find a way to allow us to return to filling the lungs with liquid for health purposes and for deep diving or space environments.
I had a furnace fail to light (and why does this always happen on a weekend?). It would light, then shutdown within a few seconds. The repair tech asked if I was handy with basic tools (I am), had me open the furnace, remove the thermocouple, and confirm it was mostly black (it was) -- then told me to grab a wire brush and brush off the carbon buildup (I used a Dremel tool) until it looked completely clean/new again. I put it back in and the furnace worked perfectly.
The advice he gave me was that ... even before you have a problem with your furnace, buy a spare thermocouple and a spare inducer fan for your furnace because these were the two most likely parts that can fail and leave you without heat. Having them on-hand means you can just swap out the parts and have heat again without making a service call in the middle of the night or on a weekend.
There is no reason to buy a spare inducer motor as they rarely just fail and there is no reason to buy a new flame sensor as they can almost always be cleaned. Now a new furnace ignitor that is a whole bother conversation. Buy an extra one actually buy two because you are likely to break the first one while installing it
The first failure on my 9 year old furnace was the draft inducer (happened earlier this week). I also had a nice crack in the plastic duct behind it and replaced that as well.
This year, I've replaced more gas forced air systems with Geo and air to air heat pumps than ever. I'm doing two 20+ seer variable systems just this week. Even with slightly higher costs on electricity in some places, the overall efficiency is so much higher, like an energy advantage of 3 to 1.
My house, in Ireland, was built for this setup - there was a brief period in the 70s that they were in vogue - but was instead set up with a resistive electric element instead. The running cost of that is likely why a previous owner got it plumbed for our more regular radiator system
@@timotheatae It can, but it is consistently referenced as the most expensive by area compared to other methods.
Timmity3 there are very very few areas (even geothermal Iceland and hydro Norway barely get there) where resistive electric is cheaper than gas or oil, and there is literally nowhere where resistive electric is cheaper than heat pump electric.
Jasper Janssen unless the resistive load is the “dump load” of a small wind power system
@@JasperJanssen Resistive electric is always more expensive than heat pump in the utility costs - but in installation, they are an order of magnitude cheaper. So if you have an energy-efficient house, or electricity is cheap in your area, installing a heat pump may make no sense, as the return on investment would take a multitude of years.
2:28 your ability to stop troll comments before they happen makes me so happy for some reason
I'd love to see a video about the radiator and boiler furnaces. That's what I've got in my house that was built in 1886.
Imagine the forced air furnace, but with water instead. Thats basically it.
@@Smok3yR1der I just imagined hot water being sprayed into the rooms. Luckily I learned to not drink while reading comments or I'd need a new monitor and keyboard.
So, how come you can't pump chilled water just above freezing and get air conditioning from it? Its not the same?
@@williamnichols2067 You can and there are systems like this. It however is not quite as easy because condensation around cold pipes is an issue. Also, you still need an AC to cool the water, so it just adds extra effort when you could just pipe the coolant around instead.
@@williamnichols2067 because during AC the refrigerant is picking up the heat from the air and moving it outside to the condenser where it is vented. Water doesn't behave properly to allow for refrigeration.
Love hearing the little fan then the snapping of the ignition system, the woosh off fuel. Lovely things. Thanks Armstrong air
A relative had a new furnace like this put in years ago now, like 6 months after it was in in midd winter it was cold in the house. They looked at it could not find issue, called installer said something is messed up with this thing you installed fix it. End up being (what they said was common issue) a bird sat on the vent on the roof, the Co2 made it pass out falling down the chimney. Then somehow the bird made it into the draft inducer stopping it from running. They later had a cap put on the chimney so this does not happen again.
Why didn't it have a cap by default???
@@absalomdraconis
santa gotta come in somehow
Most furnaces: has all these fancy safety features and lockouts to stop it from working with the covers off
My 1978 Lennox furnace: you can operate me with the covers off but don't stick your fingers in here 😂
"Heat pumps... They are indubitably the future of home space heating" Living in a house that have had geothermal heat pumps heating it since 1982, I just gotta say welcome into the future whenever you are ready :)
The best installations range from inconvenient to impossible to install after the house is built, so not so suitable to suburban & urban locations.
Jared Maddox yeah its far easier to convert if you are heating with water instead of air. Then it's just a two day job.
@@absalomdraconis If you already have central air, you can have a heat pump. The air handler replaces your existing furnace and the refrigerant lines are run just like a typical A/C installation.
@@Lawrence330 : The best systems are geothermal. Unless you have a reasonable amount of easement-free land, you can't realistically install them after the house is built, only before.
@@absalomdraconis The best heat pumps you mean. Gotcha. I mistook your statement to mean that you couldn't easily switch to a heat pump (not specifically GT) after the house was built.
Even an air source heat pump is quite efficient in the lower half of the U.S. I'm in coastal VA and have had a heat pump here for a decade. This house is very poorly insulated and ventilated, so I imagine newer/better construction would see a bigger benefit than I do.
Hey, thanks to this video I was able to identify the problem with my water heater and saves like a hundred euros calling a technician for a furnace no longer in production and with the manufacturer out of business
Oh man when he said "a series of tubes" I had a war flashback
It's okay mate. They are all dead by now
Got a new furnace a few years ago. It came in a big truck. They just dumped my old one on it.
Its not a big truck
I’m in Australia, we normally have wood fired, central heating or as what my home has is floor heating via running a fluid through tubes under the floor for each room allowing the heat radiate up from the floor.
It feels lovely to get out of bed and walk to the toilet on a warm wooden floor at the middle of the night.
Modern mountain homes here (I live in Colorado, USA) have floor heating because there's no need for central A/C if you live in the mountains. It's a cool idea isn't it.
In Finland we use wood, oil or just plain electricity for heating. In north wood is very commonly used. My father has a huge oldschool stone furnace and it takes a lot of wood to warm up, but it stays hot for a long time once warmed up.
In the Missouri Ozarks most of us grew up with wood heat. Alas, the influx of foreigners from Illinois, California, and other communist territory diluted the intelligence quotient so much that most insurance companies refuse to insure houses that heat with solid fuel. The risk of fire from stupidity is just too great.
Another Aussie. To clarify "Central heating" is our term for the gas furnace ;D
To clarify, the vast majority of Australia is too hot for any kind of dedicated heating system beyond an electric resistive heater/reverse cycle AC. The comment was referring to the colder/ more southern states and cities.
Gosh I wish I had watched this before I bought my garage furnace last year. Went with traditional instead of high efficiency and I have always wondered if that was the right choice. Just having the PVC exhaust instead of metal roof vent alone would have been worth it.
As usual, great video. Very informative.
Getting yourself a heat pump is a much better option than a high efficiency furnace. Unless you live in the very north, your annual cooling season load will be much greater than your heating season.
It's quite spectacular when the heat exchanger of an old furnace goes. The pressure from the large blower pushes the flames back out and flames come shooting out the front of the furnace, which then trips all sorts of safety features and shuts it down. There's sometimes a loud bang when it happens. It's more common than you'd think.
Alec, thank you for all the videos you make. You take the seemingly mundane objects in our lives and reveal how interesting and fascinating they really are! Please, keep doing what you do!
"Buildings constructed before we became addicted to air conditioning."
Yep, that describes my parent's house all right. Boiler and radiators, and a 600 gallon oil tank.
We had AC installed when we did a remodel soon after moving in, routing those tubes was interesting (but it was managed!).
It is a shame everyone rips out the radiator systems when they see them.
@@ArrowRaider Oh we kept the radiators. The house is like 150 years old now I think, so keeping that relic was fitting.
@@ArrowRaider yes, people really underestimate how the infrared radiation from a hot radiator makes us feel warm and cozy.
@@HenryLoenwind this video fascinated me, as over here in England I’ve never come across a forced air heat system before. We only really use the gas boiler/radiator system over here. I have to admit, it does work really well, and as you say, adds to the cost factor. Handy for drying towels too 😂
That "Ok bye" at the end killed me haha, very good video and I'm looking forward for your video with the thermal imaging camera! Also finally someones that understands the upsides of heat pumps, I live in Québec and I want to buy a house and I'm really looking for one with everything already installed.
Heat pumps are pretty useless below a certain outdoor temp. They depend on an aux system below then, and hence become very inefficient. They're terrific in relatively mild climates, but in very cold areas they're not very good.
@@nate8088 I would counter that there are always days in any climate where they're useful. Honestly, if we had been installing reversible air conditioners for the last 2 decades, we all could see reductions in energy costs and emissions. Even in areas like mine where there are plenty of nights where it wouldn't do much at all, there are also plenty of days when it would be more than sufficient. All it would take is an outside air temperature sensor to determine if it's feasible to run the heat pump. If it is, then do that! And if it's too cold, then you switch to the natural gas or other form of heating.
There's a lot of people that think of this in a binary sense that a heat pump is only valuable if it can work as your only source of heat and I think this is a very poor way of thinking. Especially since all it takes to turn an air conditioner into a heat pump is a set of reversing valves. If you are gonna have A/C, you might as well make it a heat pump and frankly I'm somewhat amazed this isn't the norm.
In Québec (Where I also live) you're most likely going to find houses with electric baseboards, even in new houses with central AC... Electricity is so cheap here that we can put a giant resistor in each room to heat. It also makes finding a smart thermostat very hard as almost none of them are made for 120/240vac (most baseboards are run from 240 - the wires in the wall should be a different color)
@@TechnologyConnections What looks promising is geothermal heat pumps. It doesn't take much to drill a hole and run a heat exchange pipe a few meters below ground to tap into that constant ground temperature year around, even at a single-family home level of operation.
Jimorian My parents got geothermal in their house and it was a huge process to dig the trench that the pipes would run in. With regards to how efficient it is they are very pleased with it and their electric bill so maybe it’s worth it.
30 years in hvac I don't no why I like this video it's good stuff
Alec is like the Bob Ross of technology and I love it
If he starts having "happy accidents" and goes on-set with a baby squirrel in his breast pocket, we'll know the assimilation is complete!
Alec: "AFUE"
Me: "Gesundheit"
(Very interesting video, as always. Going to need to replace my HVAC system in the next year or so, so well timed, too)
Use Heat Pumps as the replacement.
Finally I understand why Airbnb is so persistent about telling me if a carbon monoxide alarm is present in the flat / house.
Liability for them
@@Nicholas-f5 not dying is also a neat side effect of this corporate policy
It doesn't make so much sense in properties that are heated solely by air conditioning!
@@Nicholas-f5 I was a little bit a wonder why this was so important to Airbnb. They specifically highlight if no CO alarm is present. It's a little bit unusual because in Europe, where I live, hot water radiators are the most common heating system. That's why I found it unusual to make such a fuzz about the CO alarms. But now I know why.
I can't wait for your video on heat pumps and their challenges! As someone who lives in a municipality that is banning furnaces from new construction I'm very interested in knowing the tradeoffs of that heating system.
17:15 So THAT'S why my fans don't kick on right away! Seriously I always wondered. My bedroom looks on the 2nd floor is right under our furnace in the attic (that's in addition to the 1st floor furnace that's in the basement).
Anyway I hear the unit clock on right above my bed, but the vent over there near my door doesn't actually start spitting out air til after about one minute.
I was always MAD at the unit but...Now that I know the alternative would be to blast cold air on me...THANKS FOR WAITING, MR. FURNACE!
Fun fact: This is likely on a completely independent system, not part of the ignition sequence. My furnace is outdoors and in summer the direct sunlight gets the heat exchanger hot enough that the blower comes on, even though the main thermostat is turned off.
I used to work environmental combustion and there’s as many way to light a flame as there is to prove it.
Usually we’d light using HEI, high energy ignition, basically a neon transformer and a spark plug sometime backed up with a piezo ignition, like BBQ. Other times we use a remote system called an FFG, flame front generator, to shoot fireballs down a pipe which is advantageous in that you can add valves and light multiple pilots. These systems used continuous monitoring and automatic relight sometimes without timeout because safety concerns for flares.
As backup backup we’d use projectiles. Basically a giant six gun shooting a magnesium flare down a pipe with a hard block at the end causing them to explode. Another is the fancy industrial model rocket on a wire shooting through the flammable gas along with manual hand crank systems that hold something like a road flare. If all that fails your down to 2 systems the short straw with a handheld igniter, a match or a modified maglite with a 6ft pipe and spark plug, to good old bow and flaming arrows. Yes flaming arrows are an acceptable way to light an emergency flare in an emergency.
To prove flames we used thermocouples, flames rods, infrared, and UV. Thermocouples with a simple temperature relay was the simplest. Flame rods are more common in smaller systems and are as described in the pinned comment. The big boys use optical proving from the hotel boiler that has a Honeywell blue cube and a camera that looks for burning natural gas’s light spectrum to many thousands for a UV tuned to Hydrogen specific wavelength since its invisible to the naked eye. Some cameras are mounted opposite like in a boiler but for larger they can be ground mounted pointed at the top of a stack.
Host: “You might call them U-Tubes”
Me with a terrible Richard Karn impression: “I don’t think so Tim”
His actual name is Alec
I get that this is a joke and all but please dont call Alec "the host" It just sounds really odd
Sorry if I offended you, I couldn’t remember his name or if I had ever heard it.
watchin u tubes on the u tubes
@@rob-toolsandtech2521 burr app am
Many thanks for this video! Last week [2020 11 03] my 29 year old 80% efficient gas furnace was replaced with a 96% condensing furnace very similar to yours. Your explanations give me a better understanding of what is going on inside this cute new machine - the installer guys were too busy doing their work to give me a detailed technical lecture on modern furnaces. LOL It was indeed expensive, but my gas supplier [Fortis B.C.] is currently offering a double-rebate [$1400] so my net cost will be acceptably low once I receive the rebate check. BTW, my detailed gas bills show that the B.C. carbon tax I pay is roughly equal to the basic cost of the methane itself. All else are charges for GST, PST, storage, transportation, etc.
This was awesome! My furnace broke down yesterday and even though i only listened to this video in the background while cooking dinner, you have given me the confidence to feel fully qualified to attempt to repair it myself using only a blowtorch as a light source.
Make sure to keep your windows and doors closed, and breathe deeply the carbon monoxide. 😅
As a child, I thought adults were saying, "four stare" heating. So, when I was cold, I'd look (sternly) at the register a few times, but alas, nothing happened.
thats cause you never actually TOLD it to get warmer after staring.
i bet the poor thing though you were going to beat it.
The first models worked kind of like a clapper - stare ON stare OFF, but early adopters found the system too unstable. It could be set OFF with a passing glance.
It was Benjamin Franklin who came up with the "double stare" variant, known today as "four stare" as most users do not wear glasses.
18:45
"going from room temperature to having FIRE INSIDE OF IT"
I cackled
This video is honestly detailed enough to teach you how to repair your own furnace or at least troubleshoot it without explicitly doing so.
Anyone else remember being afraid of these things as a kid because of the weird, unfamiliar sounds they made?
I used to be afraid of a leaky toilet when I was young
My dad is an HVAC guy who works every corner of this state and they still kinda scare me lmao
I'm 21 and I'm still scared by them, so..
They burn with fire. *FIRE!* I easily see young PPL be afraid of these with fire being the brightest reason behind it. (Pun intended) I am from Sweden and we don't burn with fire to heat our homes. Heat comes from an unknown place by me to heat up water, this heated water is then pumped through multiple radiators strewn about a home, there is about 1 radiator per 2 rooms, if a room is big enough, 2 or more radiators can populate the same room and are almost always located right under a window, but this is a very rough radiator count. Temperature can be altered by twisting a big mechanical dial at 1 of the upper corners of a radiator. Some systems are slow acting, and a temperature-changing twist of a dial takes effect the next day.
@@737Garrus Radiators are trash (at least in America). They don't turn off until it's 90 to 100 degrees in the house and it feels like a heat wave. Plus, the thermostat was in the basement, which is stupid because it's _always_ cold in the basement. Sometimes in unusually-warm days (80 degrees in January), it would still turn on. We had to flip the emergency on/off switch several times just to stop the furnace from heating us to death. Not only that, but most of the radiators didn't work. I shudder to think how warm it would get if _all_ of them came on simultaneously.
"Invest in carbon monoxide alarms and test them regularly. They may just save your life."
I absolutely agree _(I say, while sitting in my parents' wooden house that has a gas burning boiler and not even a single smoke alarm)._
Sounds like a great idea for a Christmas present.
Last year I got my parents a 2-pack. We now have 4 alarms in our house and it's nice to not have to worry as much about being trapped by a house fire in the middle of the night.
@@thorlancaster5641 I didn't wait until Christmas, I installed them myself the day I noticed my dad's new-to-him place didn't have any.
@@thorlancaster5641 They also come as CO/Smoke detectors in one unit now. I have 2 in our house, one in the basement about 10 feet from the furnace next to the stairs, the other on the 1st floor hallway which connects all the bedrooms. And they will wake you up! Even with your ears covered it feels like ice picks going in your ears, it's that loud.
Carbon Monoxide is produced when there is in sufficient oxygen to complete combustion, it is a lot harder to get a poorly adjusted burner with gas than say, coal, oil or wood. Once a gas burner is properly set, unless it is somehow damaged, it should give off little to no CO. And with a sealed combustion chamber, it can draw as much air as it needs from outside without creating a vacuum in the house.
@@davidmarquardt2445 as someone who routinely produces smoke near those interconnected smoke detectors (soldering), I can confirm that they feel like icepicks. really wish yanking the batteries disabled them sometimes, I'd like to keep my hearing. at least they're effective!
Once I burnt coals in a closed bathroom
Haven't seen "a series of tubes" referenced in a looooong time. Good throwback. Now just to unclog said tubes with racehorses. :)
Or a round lottery ball!
@@racheldavis8100 Ahhh of course. The horses clogged the tubes and the balls cleared them. Golden.
@some bloke Explaining TDM does not at all get easier with a tube analogy. And it's really easy to understand. Just imagine a sales clerk at a ticket booth/popcorn stand/whatever manning multiple booths. He can only serve one customer at a time, and has to move between lines/queues. While he is serving one line, the customer who has been served has time to gather his things, leave, and the next customer step up to the counter, pull out his wallet and wait for service. If you want to go deeper, just say that he can only spend 60 seconds at each booth before rotating, and then pick up where he left off. If you want to go further still, just add that the people in the line must keep their own time and to make sure that they are ready to be served when their turn is up and have their clock synchronized with the clerk to make sure nobody is talking to dead air. But that's far more nuanced than anyone needs to go.
But you're right, it's a fine analogy to a degree, but that man's rant was incoherent and hilarious. "My secretary sent me an Internet, and it took two days to arrive" (not exact quote).
It is not a great thought when someone with such an insignificant understanding of technology is creating laws to govern it.
Good ol' Ted Stevens. You know they named an airport after him!
I just bought a house, two years ago, and it had a neglected oil boiler. I got it up and running for the first season but only used it for backup heat. I installed an electric water heater and a pellet stove. Pellet stoves have all the same safety devices as a furnace, pretty neat actually. I tore out the boiler and installed electric baseboard heaters, its a small house, for primary heat but usually rely on the pellet stove. Great video!
4:00 Here in Quebec we sometimes use electric heaters for pretty big places. Apartment buildings are notorious for using pretty much only that, so each person pay for its own heating and the building owner have pretty much no maintenance to do.
Sure heat pumps are getting more popular especially for bigger buildings, but they need to be helped by an electrical heater because it gets to cold for them to be efficient during the winter.
For houses, they often use another type of heating as the main one, but because it’s often wood based , which means it requires human interaction and it’s hard to control, there’s some electric heaters in the house to regulate the temperature and to heat it when you’re not home for a while.
EDIT: I’m not saying we don’t burn gas, but it’s pretty much only a thing in bigger cities were burning wood is regulated or just unpractical.
Exactly, HP's are efficient in places with mild winters.
@@231mac And extreme winters. They are less efficient in extremely cold weather, but even in Alaska, they still beat gas in terms of energy efficiency. Unless you live in the arctic, heat pumps are great. (Now granted, the ones that work well in extreme weather are generally more expensive, but that's getting better). Plus, even if it gets too cold for a heat pump on the worst winter days, you can just have a backup heat source and it will still save energy in the long run.
@@Owen_loves_Butters Sorry but nope. HP's are absolutely lousy in 'extreme winters', unless you think anything above 30 is extreme. I owned a Train XL series HP for 15 years and I worked for an HVAC company in the early 2000's. They work great _until_ temps drop past, I would say, 35 degrees. Then the abilities of the heat pump are unable to keep up with the demand and the system switches to heat strips, which are horrible on efficiency. And that's as good as they get, period.
@@231mac That's dead wrong. That is not even close to how good they get, you should see his videos about them.
@@Owen_loves_Butters Honestly, need to consider that with today's advancements, that I should reevaluate their abilities.
4:40 You missed a great pun. "Creates particulate matter which ..." could have been followed by " isn't particularly pleasant to breath"
What is a furnace? Well, it's a flamethrower in a box.
With a fan...or 2...
and a computer to make it turn on and off and not make anything explode or poison everyone.
This is the FORCED air furnace, that you've just described 😉
@@samerm8657 now you are just forcing the topic XD
@@Archgeek0 there's computers? that's the most unsafe part of it all
New homeowner with one of these that’s currently on the fritz. What a fantastic video! Crash course in my own furnace system! Would have liked to see a note about condensate pumps as well! We’ve reused this water vapor, but now we have water in the house that we have to get rid of!
“We’ll save that topic and its current challenges in a video in, I promise, the not too distant future”
Heat Pump video next Sunday, A.D. confirmed
You deserve much more credit for this reference than you're getting.
Thank you for posting this.
Joel or Mike?
@@alexvlk Joike
HVAC roll call!
Compressor! "I squeeze things!"
Condenser! "Juicy!"
Reversing thermal expansion valve! "Flip-flop!"
Evaporator! "Coooooold! (but sometimes hot)"
Now we know why Santa Claus refuses to go into a modern chimney that has this kind of technology.
Because it... sucks?
@@Stoney3K It doesn't.
"You might call them u tubes"
LOL! Your little jokes are what make this channel great!
Inverted U tubes are a big thing in PWR nuclear power stations.
Masterpiece of a Technology Connections video.