Hi, I have 2gensets Perkins 4016 needs to be synchronized, both runs at 1400rpm nominal frequency 46.7 hz both with pandaros governor and mx341 avr is it essential that both sets must run on 1500rpm (nominal rated rpm)before setting sw1 and sw2 in deep sea module 8610 or I can skip this step and continue with 1400rpm rated rpm
If Pre lubrication is so essential for these engines what happens when the engine is part of a standby generator set and it is required to start at a moments notice to supply electrical power,there is no pre lubrication then. I assume engine bearing damage must occur then?
Can you assist me please. I have a similar engine am working. The model is P4012 Landfill Gas is the fuel. The unit start and attain rented speed but when you load up to 35%, it strip without any dragging or decrease in speed. And the fault code that appear on the power wizard is Gas Knock fault Active . I have inspected all safety and even isolated some with no result in sight. Can you assist me on this? Thanks as I await your response soon
Check the knock ( detonation) in which cylinder connect EST program to check it the knock it happened because 1- check all cylinders for misfire by check cylinders exhaust temp. If any cylinder had low exhaust temp. 2- connect exhaust gas analyzer and check A/F ratio when engine go to close loop at more the 30% load 3-check air inlet temp. If more than 145F check after cooler 4- remove spark plugs and check for high deposits on piston or coolant,oil leak in cylinder 5- check detonation sensors and harness
Sar aap garnoter winding ka kam v karte ho os ka v vidio pio or j koi aap ka dosat garnoter winding ka kam karta hove ta os ka koi vidio lod karna jo aap jasi jankari deve pales jaroor batana
Nadeem sb very great person
Automobile Engineering Dr.nadim sir very nice
Thanks
Sar bhout vadia video apka bhout vadia jankari milti aap se
Hi, I have 2gensets Perkins 4016 needs to be synchronized, both runs at 1400rpm nominal frequency 46.7 hz both with pandaros governor and mx341 avr is it essential that both sets must run on 1500rpm (nominal rated rpm)before setting sw1 and sw2 in deep sea module 8610 or I can skip this step and continue with 1400rpm rated rpm
Good video.... What type of load test is this??? Where they put salt water, can anyone explain please?
Thanks.
If Pre lubrication is so essential for these engines what happens when the engine is part of a standby generator set and it is required to start at a moments notice to supply electrical power,there is no pre lubrication then. I assume engine bearing damage must occur then?
Great
Assalam ul alikum sir mera 1 sawal ha mf 265 1983 modal or mf 385 2020 modal k injen me kya faraq ha
Dr. Nadeem Sab very good
Bhai bulldozer Dua bahut deta ha
Black Dua deta ha turbo engine ha or
Is engine ki vajah Kya ha
Very good video
Nice g
Sir need to fill up the engine oil where is the engine oil port to pour oil
very nice
Can you assist me please. I have a similar engine am working. The model is P4012 Landfill Gas is the fuel. The unit start and attain rented speed but when you load up to 35%, it strip without any dragging or decrease in speed. And the fault code that appear on the power wizard is Gas Knock fault Active . I have inspected all safety and even isolated some with no result in sight. Can you assist me on this? Thanks as I await your response soon
Check the knock ( detonation) in which cylinder connect EST program to check it the knock it happened because
1- check all cylinders for misfire by check cylinders exhaust temp. If any cylinder had low exhaust temp.
2- connect exhaust gas analyzer and check A/F ratio when engine go to close loop at more the 30% load
3-check air inlet temp. If more than 145F check after cooler
4- remove spark plugs and check for high deposits on piston or coolant,oil leak in cylinder
5- check detonation sensors and harness
❤
Is this 4000 series engine a reliable one.
Is this a good model.
How much load it can take in percentage
Hi sir great job you are great sir
Good vidio ndeem saab
Asim spain
Thanks!
Aap perkins ka hi kaam karte hai kya zada
Ma shah Allah g
Sar aap garnoter winding ka kam v karte ho os ka v vidio pio or j koi aap ka dosat garnoter winding ka kam karta hove ta os ka koi vidio lod karna jo aap jasi jankari deve pales jaroor batana
very good sir
Thanks
Thanks sir
Hi sir which chemical do use engine cleaning
Good
Tappet Kaise setting Karena h
Nice
👍
How we can change engine oil
❤١٠٠. ١٠٠
السلام عليكم أنا من العراق اتمنى ان تكون شرح بلا الغه عربيه
Sir itna experience ho k totiya lgai hy maza ni aya
bute fall 😮😮😮
hi sir
Sir apna number send kr do
03219472206
Nice
Is this 4000 series engine a reliable one.
Is this a good model.
How much load it can take in percentage
A bit reliable
No it is not good
75% can it take
If used above 75 percent it is not reliable
Nice