Vanquish VS4-10 Phoenix gets a HW Quickrun Fusion 1800kv
Вставка
- Опубліковано 1 лис 2024
- Vanquish VS4-10 Phoenix gets a HW Quickrun Fusion 1800kv and a test run.
Need to adjust a few settings (reverse speed) but performed very well.
#Vanquish #vs410 #phoenix #hobbywing #fusionSE #rcrockcrawler #rccrawling #rc #trx4 #axial #rctoys #rccars #offroad #rock #jeep
Quick runs are great cool looking course
Thank you, I really appreciate that 🙏
My course is small but working on it.
I like build the course as much as running it lol
I have one on my straight axle. I had to dial down reverse quite a bit as it was too punchy. Love it.
The video keeps me surprised. Great R/C, it's really cool. 👍🏻😀👊
Thank you 👍
A great up-grade my Friend! Makes all the diference!
Awesome Course ❤
Definitely a smoother and more powerful motor. Thank you 👍
You are Welcome my Friend! I recently install the 1800kv in my Wife RGT and was a new RC
@@pandacrawler6x6 they are a fantastic upgrade, definitely 👍
Indeed my Friend 💪🏻🐼👍🏻
I love the 2300 pro for sure, plenty of wheelspped for this heavy rig..
The HW 2300 pro is the best brushless motor I’ve had so far. Thanks for watching and the feedback 👍👍
cool vid, my friend! big like! 👍👍👍
Thank you 👍
Great video!!! Man Im really considering one of these phoenix rigs
They are without a doubt one of the best out of box RTR crawlers. Always places for improvement depending on your needs but it’s a very good rig.
Hello,
Great video, thumbs up from me!👍
Greetings Seven🖖
Greetings Seven!👋 thank you again sir!
very good rc😍
Thanks ✌
nice video.
👏👏
like😃💕🍀
Thank you for watching! Much appreciated.
Just subbed! Could you help me with telling me about fitment? When I got my first phoenix I couldn't fit the fusion pro into it at all. Anything special needed to fit them? Thanks you rock bro 😎 keep crawling!! 💪
Thanks so much! Very appreciated!
So I have Fusion SE 1800kv in my phoenix, not the pro. However they have the same dimensions so fitment should the same. Is was tight getting motor to seat but nothing special other than gentle force 😂 I did put the pinion gear on after I had the motor seated and the two screws loosely secured. If you have pinion gear on before putting the motor in it’s super tight. Can be done but not advertised. If you leave the pinion gear off, it’s tight but not bad at all.
Hope that helps a little 🙏
@@NEO-RC much appreciated 🙏 😎💪👊
Was it a direct fit?
Sure was
Do VP foams make the tires stop wrinkling or help?
I apologize for the late response and not sure what you mean by VP foams. I’m running the Vanquishe dual stage foams in the Phoenix and the tires do wrinkle a little but nothing too bad.
Vanquish Products, thanks. Just ordered a set for mine
@@Drwack-qz4nm 👍😂 makes sense
Hey..are u using vanquish dual stage foam in this video? Do u think it helps much? And does it wrinkles as much as the stock foam one?
Yes sir I am using the vanquish dual stage foams in the falken wildpeak tires. They don’t wrinkle as much with dual stage foams but I also have an issue with their tires spinning on the rims, their method racing rims.
@NEO-RC ahhh i see..so u dont recommend the vp dual stage? Im planning to get one..im using boom racing wheels
@@rudykwan9196 they are good dual stage foams, I just like the silicone or 3D printed inserts better. That’s just me, everyone likes their own thing. If you don’t run in water, the 2 stage vanquish foams will do just fine.
@@rudykwan9196 thanks so much for watching and commenting!! Really appreciate it! 👍
Do u notice clicking noise when using fusion?
Yes I do but I assume it’s because I have the pinion gear on the motor too tight against the spur gear. I just haven’t gotten back in to adjust it yet. But yes I do hear a clicking
this is the ugliest rc crawler i know😂
Was it a direct fit?
Yes sir it was a direct fit.