best way to make dovetail cutter

[@hosseinnoorafshan1844]

Very good nice ✌️🌱💎🔥

[@MadebyEG]

ممنون از شما

[@alirezanabizadeh8547]

mashalla dadash ehsan

[@MadebyEG]

ارادت داش علی

[@SherliGood]

بسیار عالی و آموزنده ❤

[@MadebyEG]

ممنون

[@shirezknife5298]

درود خسته نباشید خیلی عالی سلامت و سربلند باشید برادر گرامی

[@MadebyEG]

تشکر از همراهی شما

[@hesamer4296]

خسته نباشی اقا احسان

[@MadebyEG]

ممنون لطف دارید

[@rezamamaghani7136]

کار تون عالی ❤❤💪💪

[@MadebyEG]

تشکر از شما

[@SaraGharib1321]

استاد کارتون عالیه 🙏🏻✔️

[@MadebyEG]

سپاسگزارم از توجه شما

[@ehsanbeigy9810]

استاد هزار ماشاالله، همه فن حریف هستین

[@MadebyEG]

ممنون لطف دارید

[@mysamans8732]

Excellent

[@MadebyEG]

Thanks

[@ElenaZare-kc3mx]

خسته نباشید عالی بود

[@MadebyEG]

ممنون عزیز

[@هستیگودرزی-و1ص]

Perfect

[@MadebyEG]

Thanks

[@aligolestani904]

بسیار عالی 👍👍

[@MadebyEG]

تشکر

[@savistech]

Well done 👏

[@MadebyEG]

ممنون

[@MadebyEG]

تشکر

[@پیامغلامی]

Good job

[@MadebyEG]

Thanks

[@soodabehzare1516]

عالی

[@MadebyEG]

تشکر عزیزم

[@TigerCarpenter]

I aslo came to conclusion to shift the cutting eges by half of the insert thickness from the actual center.
You will be getting 60 degrees because the insert is exactly that.
The tool is just merely a holder and its good based on my experiments to have bigger clearance between cutting edges and tool edges.
Initially I made it nearly flush, and the chips were halting the mill, making very loud knocking, couldn't go higher than 400 RPM. And even with shallow cuts, it was stalling and damaging the surfaces.
I know it looks strange but that clearance prevents the chips from pushing themselves between the tool and the material

[@MadebyEG]

It is not an efficient tool at all, It damages the device. It is better to use a ready hss blade

[@EGhandmade]

Good job

[@MadebyEG]

Thank you

[@mohamadyarinejad7794]

به‌به ،❤

[@MadebyEG]

تشکر

[@rizesaz8457]

عالی 👌🏻

[@MadebyEG]

تشکر از شما

[@MaryamJazayeri-wv3nh]

good job

[@MadebyEG]

Thank you

[@FZare-i3z]

Perfect

[@MadebyEG]

Thank you

[@shabnamr1607]

عالی استاد عزیز

[@MadebyEG]

ممنون

[@مهدیسیروس-ر9ق]

دقیق و تر تمیز

[@MadebyEG]

تشکر از همراهی شما

[@AdrinaAkbari-ft9by]

Amazing

[@MadebyEG]

Thank you

[@MohammadMoosavi-e8c]

Good

[@MadebyEG]

Thanks

[@1crazypj]

Shouldn't the cutting edge be on centre to get a reasonably accurate 60 degree angle?
That cutter is waaaayyyyyy above centre and trailing edge may actually be rubbing?

[@MadebyEG]

Thank you for your opinion. If we use an angled insert like tcmt, yes, it should be in the center. But with this type of insert, we placed it higher than the center so that its rear edge does not engage with the work piece. This work is only effective in this case and is ineffective at an angle of 60 degrees

[@ramtinshams2785]

استاد یه ویدیو جامع هم‌در‌باره ی تیز کردن‌کارد بزارین❤️

[@MadebyEG]

حتما حتما

[@rezakeshavarz-z6m]

👍

[@MadebyEG]

Thanks

[@hardman7768]

واقعا عالیه

[@MadebyEG]

تشکر

[@junajolopezgonzalez391]

Привет с Канарских островов, Испания, я бы поставил на него 2 лезвия, у него был бы больший диапазон резки, и я бы соблазнил тело клубники, привет 🇮🇨🇪🇸🫂

[@MadebyEG]

Здравствуйте, спасибо, что присоединились к нам, да, это правда и две или четыре цифры мощнее, в будущем буду ставить четыре цифры, для этого я сделал цанговый блок.

[@junajolopezgonzalez391]

@@MadebyEG ola me lo puedes traducir al español gracias hermano 🫂🇮🇨🇪🇸

[@MadebyEG]

@@junajolopezgonzalez391 Hola, gracias por acompañarnos, tiene razón, dos números o cuatro números son más potentes, en el futuro pondré cuatro números, hice el bloque de pinza para este fin.

[@junajolopezgonzalez391]

@@MadebyEG es por el equilibrio del corte i el balance saludos 🫂🇮🇨🇪🇸

[@davidwillard7334]

Way to much ! Bang ! cutting ! Should be more Smoother Cutting !

[@MadebyEG]

about which case? Filming or working

[@Зробленоруками]

лайк підписка

[@MadebyEG]

Thanks

[@antongyrt4814]

Это какой-то ужас.