This is so cool, if you improved this a bit, closed up some of the water spillage over the sides and then hooked it up to a battery, you'd be generating roughly 1kWh of electricity a day. The even cooler part is the river keeps going so could could set up a few of these down the river and you could easily generate enough electricity to power your house
Hi there, honestly lovely work! Was hoping to ask if you could lead me into the right direction when it comes to choosing the design parameters of the turbine, like revs, blade twist angle and so on. Best regards
Bravo, complimenti dall'Italia! 0,3 amp. con 130 volt, giusto? fanno 39 watt. e non sono così pochi! Chiaro che il ventilatore che hai provato è potente e la frena. Ma se la tua turbina a vite d'archimede la utilizzi con motore trifase in bassa tensione, un brushless a 12 o 24volt, accoppiandola a un regolatore di carica, una batteria e un inverter hai creato un perfetto micro impianto, in grado di fare funzionare perfettamente luci e piccoli elettrodomestici di casa. Se la costruisci con tre principi, tre eliche, migliori l'efficienza. Complimenti ancora!👍
I wonder how a undershot waterwheel would perform in this stream. Would probably work better and easier to design and make than the archimedes screw. I do admire your craftmanship.
My I add something, wat about mounting the water wheel horizontal In The water flow , would that eliminate the under/over shot need. Also make it out of c/fibre , put a large drive wheel on the drive shaft , connect to a significantly smaller drive wheel connected to vertically mounted generator
@karaabdelkader1273 horizontal or vertical doesn't matter. If you place a small gear on the output shaft and transfer the that power via belt/chain to a larger gear , you will get slower revs , but more torque. Which for things like driving water pumps , flour Mills is best. But for electrical generation you need I believe large gear on output , small gear on drive shaft. I think it's large gear to small, high revs , low torque. Small gear yo big gear , low revs high torque
The advantage of the half-pipe is that it self-clears debris much more than a full pipe which would need an (admittedly coarse) mesh filter, which tends to clog up.
use the alternator from a car and run everything on 12 volts, lights, Radios, fridges TVs all run on 12 volts now, it is the standard voltage for outdoor equipment and all caravans and boats run 12-volt systems, It is also easy to store the power you are producing as all leisure batteries are 12 volts,
Thanks, sangat bermanfaat sekali.. Tetapi saya memeliki beberapa pertanyaan: 1. Apakah bearing di tenggelamkan di dalam air akan merusak bearing? Dalam jangka panjang pelumas di dalamnya akan hilang oleh air 2. Adakah bearing yang tahan air? Thaks.. Good
Если бы была возможность сделать это всё идеально, стык в стык и из нужных материалов, чтобы усилить давление на шнек, то думаю, можно было бы вырабатывать ещё большее напряжение👍
I think 🤔 the main gear with the chain should go longer to the point it’s going to be over the water label and also utilize a bigger gear on the main shaft , but other than that it’s an amazing job done ✅ men 👏👏👏👏
FAKE ...FAKE.. Don't make fool your audience. Only video editing.. All fake.The water pressure is very less. It couldn't run the pulley. If run rpm is very less. How it's generate 120 v ?
133 V x 0,3 A = 40 W x 24 h = 960 Wh . Nice ! :) Bravo ! :)
where is this coming from?
PVC companies will always smile when they see you coming.
Muito simples e prático
Encase it in a pipe for more efficiency?
This is so cool, if you improved this a bit, closed up some of the water spillage over the sides and then hooked it up to a battery, you'd be generating roughly 1kWh of electricity a day. The even cooler part is the river keeps going so could could set up a few of these down the river and you could easily generate enough electricity to power your house
what type of battery would you use though
Could use similar storage batteries used for off grid type spots with solar?
COOL.CLEAN ENERGY.
Hi there, honestly lovely work! Was hoping to ask if you could lead me into the right direction when it comes to choosing the design parameters of the turbine, like revs, blade twist angle and so on. Best regards
Bravo, complimenti dall'Italia! 0,3 amp. con 130 volt, giusto? fanno 39 watt. e non sono così pochi!
Chiaro che il ventilatore che hai provato è potente e la frena. Ma se la tua turbina a vite d'archimede la utilizzi con motore trifase in bassa tensione, un brushless a 12 o 24volt, accoppiandola a un regolatore di carica, una batteria e un inverter hai creato un perfetto micro impianto, in grado di fare funzionare perfettamente luci e piccoli elettrodomestici di casa.
Se la costruisci con tre principi, tre eliche, migliori l'efficienza.
Complimenti ancora!👍
Great! And hilariously retro. It alone could save at least 1/2 the Whurld! Cuz only 1/2 of it is in the Water. Harhar
I wonder how a undershot waterwheel would perform in this stream. Would probably work better and easier to design and make than the archimedes screw. I do admire your craftmanship.
Thank you. maybe we should try it
My I add something, wat about mounting the water wheel horizontal In The water flow , would that eliminate the under/over shot need. Also make it out of c/fibre , put a large drive wheel on the drive shaft , connect to a significantly smaller drive wheel connected to vertically mounted generator
@@davewarrender2056 you mean like using gears to increase the motor input shaft speed? Will it produces more power?
@karaabdelkader1273 horizontal or vertical doesn't matter. If you place a small gear on the output shaft and transfer the that power via belt/chain to a larger gear , you will get slower revs , but more torque. Which for things like driving water pumps , flour Mills is best. But for electrical generation you need I believe large gear on output , small gear on drive shaft. I think it's large gear to small, high revs , low torque. Small gear yo big gear , low revs high torque
@@davewarrender2056 I really appreciate it, you really had no idea how much I needed this
Chain in water...very good.
very nice work lovely made
Thanks 🌹🌹🌹
very professional! :) It looks like you have found the perfect river to test these in.
Great video sharing
Thank you
Very professional work, Thanks my friend, Big like ♥️♥️♥️♥️♥️
Cool.!
My guess would be that it will work better in a full pipe instead of the half pipe, so pressure could buildup. Also being vertical should help.
probably so
The advantage of the half-pipe is that it self-clears debris much more than a full pipe which would need an (admittedly coarse) mesh filter, which tends to clog up.
use the alternator from a car and run everything on 12 volts, lights, Radios, fridges TVs all run on 12 volts now, it is the standard voltage for outdoor equipment and all caravans and boats run 12-volt systems, It is also easy to store the power you are producing as all leisure batteries are 12 volts,
Great Job 👏 ✅ But I wonder why you don’t use a bigger gear on the main shaft in order to multiply revolutions even more !
I've also had some videos with a system with a higher gear ratio, but it probably won't work if it's too big
@@mr.construction9846 if we use gears to increase the motor's input shaft rpm, will that means more watts?
Gearing something for high revolutions reduces your torque. Easily shown in the video where connecting a fan nearly completely stalls the turbine.
great! with what tool do you make the hole in the pvc plate? (when you snap your fingers 😅)
How much loss from those loose chains I wonder...
Tight chains would have added friction
Chains are normally 95% efficient
The larger the gear coming out of the turbine, the faster it will spin the generator.
Hay quá
Cảm ơn bạn
Inlet as a bell siphon may improve that
Thanks for the details. You videos have tremendous improvement every time!!
Thanks, sangat bermanfaat sekali.. Tetapi saya memeliki beberapa pertanyaan:
1. Apakah bearing di tenggelamkan di dalam air akan merusak bearing? Dalam jangka panjang pelumas di dalamnya akan hilang oleh air
2. Adakah bearing yang tahan air?
Thaks..
Good
A grease box like a propeller shaft on boat would solve that.
@@nzs316 oke tks a lot
Steel chain in the water... What can go wrong?
what material is that thing you add to the frame at min 2:55 made of?
It would be better in reverse as a grain auger to lift grain
What is the gear ratio for this?
Если бы была возможность сделать это всё идеально, стык в стык и из нужных материалов, чтобы усилить давление на шнек, то думаю, можно было бы вырабатывать ещё большее напряжение👍
В яблочко
👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻
👍👍👍🌹🌹🌹
Can that spiral propeller can also be used as a silent propulsion for motor boats?
Good invent, but....
You may think a solution to prevent the chain get rusty...
Especially the one that soaked in water.
I think 🤔 the main gear with the chain should go longer to the point it’s going to be over the water label and also utilize a bigger gear on the main shaft , but other than that it’s an amazing job done ✅ men 👏👏👏👏
Best video of the day ! Thankyou for showing us your build !🍻
Can you told me what glue you used ?
Can you tell me what the diameter is from the screw? And couldn't you run a bigger dynamo on it?
Можно сделать передачу со шнека сразу на вентилятор😄
Can you tell the dimensions please😊, because i need to make a prototype for archimedes screw turbine for my school project
Ganti pakai kipas yg gede ya bos
Làm tua bin gió đc không bạn?
It seems I will visit in hardware store to buy stuff for new project...
👍👍👍👍
can i use 220 v ac motor?
Maybe we can use DC through the booster
Hi is that an unwinded AC Motor?
Can I replace the iron frame to be wood or no ??
As long as it's sturdy enough, of course
Please, what is the area of the entrance of the frame to determine the velocity of water??
Is any generator can used in Archimedes turbine ??
0:36 dùng cái gì để cắt vậy
Probably the same angle grinder
4:50 😂😂😚😚👨🏭👩🏭
🌹🌹🌹🌹🌹🌹
So, the voltage is fine but how many watts are you getting?
Power = volt × ampere
what is it called the thing inside the bearing to lock the rod to the bearing???? 3:18
It's called a saddle bearing or pillow block. The bearing is connected to the shaft via grub screws.
what are the sizes or models of those sprockets??
izin bertanya,gear yg dipkai itu namanya gear apa?
Ini adalah motor AC yang bisa Anda lihat di sini : bit.ly/3lfjnW7
Sir how many volt DC motor have you used?????
It is the motor of the air conditioner 110v 52w
dc motor 24V 250w 2750 rpm,this motor and the motor use using is similar?
Me interesa para mí finca
It will be proportional to what you get
感谢先生，这套系统装到小型船上比较好，自我循环充电推马达，船棚上在安装一套太阳能系统。船跑起来带动的风安一套风力发电系统。这是永动机船哪😃
It rotates, but under load it stops. Seems it is not able to deliver power...
What is it made from ?
The screw is made of pvc, the motor is the motor of the air conditioner
Hola todo está bien sólo preguntó de donde sale el agua?desde Argentina saludos
Esta pregunta es bastante difícil, es un problema de todos.
La turbina ni siquiera gira...
When in the video is that? He pauses it at one point to make it easier to see the multi meter
pesou....................
))) Дико тупой развод
FAKE ...FAKE..
Don't make fool your audience.
Only video editing..
All fake.The water pressure is very less. It couldn't run the pulley.
If run rpm is very less.
How it's generate 120 v ?
Thank you so much for every video you watch and leave a review, even though it's not from your head
Would the water pressure increase, if you'd let the screw run through a closed pipe? Would that be a solution?
It is probably real because I have got an couple volts from a tap before