Back in the day we used to have to pump the oil on to the bearings with a hydraulic type pump system ! I used to print on a huge 6 color hidelburg printing press built in the 30,s or 40,s and we had to hand pump the oil to all the bearings and it's still being used lol where there's a will there's a way to make it work !
Isn’t that a green nitrile o-ring on the piston? That would explain why the vacuum in the cylinder was maintained for so long. Ring gaps would’ve lost the pressure in a couple seconds.
for precidse parts you need machining tools, however it is possible to make an engine using your hands, it just won't be as powerfull and could have small leaks or other problems
Why not vertical like everyone does it? We want to contain 100 bar and you even have the wrong orientation on the main bearings? Going for a flat-2 in the end?? Those thin bolts may just rip off.
Sounds like it will have enough compression!
Because it’s sealed with a nitrile o-ring.
No lube to crank and ring how can it last? Good time not long time.
Back in the day we used to have to pump the oil on to the bearings with a hydraulic type pump system ! I used to print on a huge 6 color hidelburg printing press built in the 30,s or 40,s and we had to hand pump the oil to all the bearings and it's still being used lol where there's a will there's a way to make it work !
Isn’t that a green nitrile o-ring on the piston? That would explain why the vacuum in the cylinder was maintained for so long. Ring gaps would’ve lost the pressure in a couple seconds.
I thought the same. It really looks like it.
Altough it has good compression it would probably melt when it would start
Looks like HNBR o ring should be fine for a but
Good compression. But its sealed with a rubber ring. It would melt if you started the engine
It has very good compression, good job!
Good job !
Compression is very good!
Is that a Honda GX50 crankshaft assembly? Or maybe from a Stihl chainsaw?
good job
厉害👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻
how can i make one?
В чем прикол этой якобы многообещающей музыки😂
The music sounds like "Delirium"
Nice job, did you use any machining tools or completely diy with ready to use components
for precidse parts you need machining tools, however it is possible to make an engine using your hands, it just won't be as powerfull and could have small leaks or other problems
how do you lubricate it?
Your mum squats over it.
That's awesome how do u find spark timing
he will probably use a contact breaker
After all the other more important parts are done.
Bel lavoro! Vuoi realizzare un motore Stirling?
❤❤❤❤❤❤❤❤❤❤
Why not vertical like everyone does it? We want to contain 100 bar and you even have the wrong orientation on the main bearings? Going for a flat-2 in the end?? Those thin bolts may just rip off.
Это какая-то проблема.... Резиновые поршневые кольца😮
Parabéns amigo
😱I understand your message perfectly, be careful to make it work sin combustible solo con autocompresion
your turning it a deferent way,clockwise not counter clockwise, turn it clock wise
Компрессия лвл99999999😮
Just get a dirt bike
that is not compresion it is depresion
Vacuum, you mean?
NO cooling blades.
What? That’s what you noticed missing? Not the valvetrain, cam, oiling, intake, exhaust, ignition? Fan blades?!? 😂
This would be a 2 stroke
І що???
ICPE. INTAKE, COMPRESION, Etc Etc...unfinished but cool little piece of of machinery.
how can i make one?