Hi Adrian--I am down to the short block on a 1978 450SL and need to know a few things. First is that I cannot seem to find a source for new crankshaft bearing bolts--ten of each. The manual just refers to checking the depth of the threads--does not say to replace them, but a person should, shouldn't they? Second, there are no scratches, but engine sat a long time and the cylinders need to boring to clean them up--how much is safe before the need for oversize pistons and rings (which are not available)? A fingernail test of the cylinder walls shows no wear lip at all on the cylinders. Thanks for the reply and a wonderful video.
Hi , if the bolts for crank shaft rods are not extended you can use them again ( mine were too long ) it’s difficult to get them so i’ve made them again from scratch. Main bearing bolts usually are not needed to replace. If they are extended you can change them by buying hardened ones in the shop ( 12.9 ). they are going to work perfectly. If you dont feel lip/ step on cylinder it’s Ok to Just clean with sand paper or polish it . Even with little step engine is going to work for ages, Just change piston rings for new nominal ones. Regards
That is a nice restoration...I have a 1974 450sl and the engine and transmition need total restoration. Can you do that for me? How much is the cost of this restoration
Me podes ayudar con la medida de apriete de los tornillos de bancada de cigueñal y de biela de motor 117 mercedes gracias amigo amigo de guatemala City
Yes it's possible but difficult. K-jetronic needs to be removed or readjusted. Second option is changing it to a electronic injection system ( stand alone ECU ). As I saw these kind of projects there was a lot of efforts like changing/rebuilding intake manifold because of too less capasity under "piping ".
Nice job on the rebuild! Beautiful cross hatch pattern on the cylinder walls. Did you have someone - is it zinc plate or dip your hard fuel lines and other parts at 4:28 and 4:32 to get them shiny and gold like that? Or is it brand new parts? They look great! Makes me want to do my engine! Also what did you do the get the intake manifold so beautiful and shiny silver? It's gorgeous!
I knew how to make it before. To galvanizing you need to have good laboratory DC power supply and buy " zinc " bath for galvanizing. You need also fine a " very clean " anode.
Hi. Can you give me an advise please? I have sl350 R107 M116.982 engine and despite of adjusting valve lash it keeps on knocking like excessive valve lash. I suspect that thrust pieces between top of valve and rocker arm might be worn. Can rocker arms be removed without removing camshafts? Liked your video, nice job. Drive safe.
Hi.Probably rocker arm is worn or camshaft. You can remove rocker arm by pushing down valve spring by bigger screwdriver. Be aware that it's not so easy, you need to put some force. check if piston is at "down " position. Better is to do it with some help. You can buy different thickness thrust washers if needed. Regards
Beautiful work! I'm doing the same on my 380SE engine at the moment. Pain in the ass.
+Jack Rosenfeld Good luck ! Mercedes engines were complicated a little in 70's and 80's
Wow! I wish I had a fraction of your skills.
Thanks a lot
Beautiful work mate 😊
Thanks
Excellent job mate!!!
Thanks
@@adrianwalio how many hours did the job take?
Christopher Marshall , it was arround month but i was waiting for parts and had some brakes ;)
Great job!
Super tato 👍🏻👌🏻
Bravisimo..super job!
Thanks
nice work pal
Hi Adrian--I am down to the short block on a 1978 450SL and need to know a few things. First is that I cannot seem to find a source for new crankshaft bearing bolts--ten of each. The manual just refers to checking the depth of the threads--does not say to replace them, but a person should, shouldn't they? Second, there are no scratches, but engine sat a long time and the cylinders need to boring to clean them up--how much is safe before the need for oversize pistons and rings (which are not available)? A fingernail test of the cylinder walls shows no wear lip at all on the cylinders. Thanks for the reply and a wonderful video.
Hi , if the bolts for crank shaft rods are not extended you can use them again ( mine were too long ) it’s difficult to get them so i’ve made them again from scratch. Main bearing bolts usually are not needed to replace. If they are extended you can change them by buying hardened ones in the shop ( 12.9 ). they are going to work perfectly. If you dont feel lip/ step on cylinder it’s Ok to Just clean with sand paper or polish it . Even with little step engine is going to work for ages, Just change piston rings for new nominal ones. Regards
Thank you!
That is a nice restoration...I have a 1974 450sl and the engine and transmition need total restoration. Can you do that for me? How much is the cost of this restoration
Hello, I'm sorry but I don't do that for money. Time for making it is just incredibly long.
Me podes ayudar con la medida de apriete de los tornillos de bancada de cigueñal y de biela de motor 117 mercedes gracias amigo amigo de guatemala City
beauty !!!
Thanks
witam, czy mógłby mi pan zdradzić czym pan polerował elementy w tokarce bo pod tamtym filmem są zablokowane komentarze
Witam , papier. pasta i dużo cierpliwości. Niektóre elementy były zamienione na nierdzewne
@adrianwalio Do you think it's possible putting a supercharger on the M117 and M116 engines? Just curious and wanted to know your opinion on it!
Yes it's possible but difficult. K-jetronic needs to be removed or readjusted. Second option is changing it to a electronic injection system ( stand alone ECU ). As I saw these kind of projects there was a lot of efforts like changing/rebuilding intake manifold because of too less capasity under "piping ".
Nice job on the rebuild! Beautiful cross hatch pattern on the cylinder walls. Did you have someone - is it zinc plate or dip your hard fuel lines and other parts at 4:28 and 4:32 to get them shiny and gold like that? Or is it brand new parts? They look great! Makes me want to do my engine! Also what did you do the get the intake manifold so beautiful and shiny silver? It's gorgeous!
Hi , Thanks for comment . I’ve zinc galvanized it. Intake manifold was blasted by micro glass granules. All aluminium parts were done this way
adrianwalio that's cool! Did you learn the process on UA-cam? I've heard of some people doing it themselves.
I knew how to make it before. To galvanizing you need to have good laboratory DC power supply and buy " zinc " bath for galvanizing. You need also fine a " very clean " anode.
adrianwalio thank you for sharing.
Please redo the video with much longer time on the pics. I'm having to hit pause on nearly every one to look at it properly. Otherwise good.
Hi. Can you give me an advise please? I have sl350 R107 M116.982 engine and despite of adjusting valve lash it keeps on knocking like excessive valve lash. I suspect that thrust pieces between top of valve and rocker arm might be worn. Can rocker arms be removed without removing camshafts? Liked your video, nice job. Drive safe.
Hi.Probably rocker arm is worn or camshaft. You can remove rocker arm by pushing down valve spring by bigger screwdriver. Be aware that it's not so easy, you need to put some force. check if piston is at "down " position. Better is to do it with some help. You can buy different thickness thrust washers if needed. Regards
Thanks for answer. I have opened valve cover and camshaft looks to be fine. So It is either rocker arm or that thrust piece.
+pasifsc
hi, do you have hydraulic lifters or mechanical?
mechanical
ok, Just wanted to be sure, check rocker first.
Good day!Please tell me where you can buy new parts?
www.autohausaz.com/They have everything.
www.autohausaz.com/
Good day!Give me please email.
No, I give up
to ja
Good day!Give me please email
walio@o2.pl