They look alot like MIP driveshafts or Incision. Should do well under power and last a long time. The best thing I've found to keep the speaking away is WD-40 gel lube spray. I also use it on my cv joints. Repells dirt/dust and doesn't sling completely off at higher rpm. Great video today.
I recommend getting the 550 can Traxxas Maxx motor. Its 2400kv and way better then the stock motor for run time, Temps, and power. All you have to do is notch the plastic wire guard to get it to fit. Have a buddy with your exact same setup but uses that motor mod and it will flip great. I'd give it a shot man, its impressive. The blx130 has proven to be a tank, but the stock motor gets hot with all the extra weight. We tend to stay tin the 130 range with the Traxxas motor.
Dang. Them. Jumps landed tough. How do you get it to drive so straight. Is all the vitavon upgrades. How much you got in parts not including time into this rig
The ryfy is a all around vehicle seems a very fun fun rig...i just dropped the Lazernut jumping jumping sky high all stock still...# Lazernut on V&B speed ✌👋🇺🇸🌏🌏Cream of the crop
nice! just bought traeal aluminum axle housings for mine(sorry) a little cheaper. will see if they are as strong. your ryft is bad ass.i think i will do the vitiavon drive lines and trailing arms and links though.i got those same rims for mine from your link.
Treal has some nice stuff and I’m Sure they would take this. I’ve seen somewhere someone bent another brand arm. Well I don’t think they were Vitavon because these didn’t bend. LoL.
I keep loosing u joint pins so now I bought the vitavon driveshafts....Is it just me or does the weight of the heavier drive shaft carry momentum longer after you let off the throttle? It seems like I have to let off the throttle sooner launching up hills. I have two Ryfts (less then 6months old) that both also have loose u joint pins in the axle shafts....I can't find anything anywhere about how to fix or avoid this problem. They chewed into the plastic knuckle and I'm only lucky I haven't lost them. If anyone has any helpful comments relating I'd very much appreciate it.
My problem with Vitavon product is for each axle housing you could buy a new RC for each link setup you've bought half a new RC. I understand it can cost a lot to upgrade an RC but at what point is $3-500 per upgrade just too much? It's getting to the point where it's killing part of the fun of the hobby, upgrading. Appreciate your content but you've become a Vitavon representative or are you only representing high end stuff because the rest is not worth your time? I can see why you need so many patreons.
That set up is probably as close to bullet proof as you can get.
Love it 👍🏻
Yeah for real.
Live seeing how Cool the exoplex transformed
ServoAF servo savers really do there job. Awesome stuff bud
Yeah they do
Looks like a perfect spot what a great rig
True testament of parts. Awesome video Joe!
They look alot like MIP driveshafts or Incision. Should do well under power and last a long time. The best thing I've found to keep the speaking away is WD-40 gel lube spray. I also use it on my cv joints. Repells dirt/dust and doesn't sling completely off at higher rpm. Great video today.
Love the editing man
You are a funny guy and the videos are getting better by the week!
Thanks! 😂😂 those hits were so bad I had to warn myself.
I can't believe one of the diffs didn't skip a tooth, or explode! That was impressive!
Okay Okay Vitavon or nothing!!!
LoL yeah it took it
Thank you Joe, that Ryft is one tough machine. Say is it possible to drill a hole in the Vanquish horn. 😎 future me 👍💯
Joe that was an Awsome beat down…!!! Love starting off my mornings with ur vids..!!! Sweet content bro!!!🤘✌🏼
I recommend getting the 550 can Traxxas Maxx motor. Its 2400kv and way better then the stock motor for run time, Temps, and power. All you have to do is notch the plastic wire guard to get it to fit. Have a buddy with your exact same setup but uses that motor mod and it will flip great. I'd give it a shot man, its impressive. The blx130 has proven to be a tank, but the stock motor gets hot with all the extra weight. We tend to stay tin the 130 range with the Traxxas motor.
It’s got a 13t pinion as well. These tires just don’t seem to have the mass needed for backflips.
Man people don't realize HOW HEAVY THAT RIG IS MAN!!! FOR IT TOO TAKE THAT KINDA ABUSE BRO IF YA AINT A BELIEVER IN VITAVON THEY SHOULD BE NOW JOE🤘🤘
Just over 10lbs. And yeah this was a crazy hard bash session
Dang. Them. Jumps landed tough. How do you get it to drive so straight. Is all the vitavon upgrades. How much you got in parts not including time into this rig
I see that RC sitting behind you 😉
LoL yeah
The ryfy is a all around vehicle seems a very fun fun rig...i just dropped the Lazernut jumping jumping sky high all stock still...# Lazernut on V&B speed ✌👋🇺🇸🌏🌏Cream of the crop
What steering link are you running I’m trying to find one like it for my trx4
nice! just bought traeal aluminum axle housings for mine(sorry) a little cheaper. will see if they are as strong. your ryft is bad ass.i think i will do the vitiavon drive lines and trailing arms and links though.i got those same rims for mine from your link.
Treal has some nice stuff and I’m
Sure they would take this. I’ve seen somewhere someone bent another brand arm. Well I don’t think they were Vitavon because these didn’t bend. LoL.
@@ExocagedRC I’ll do the rest of the upgrades with vitavon. Especially after that nose plant. Lol. 👍.
if ya pause when it hits the floor at 8;05 you can see dragster style ripples on the rear tyres as the drivetrain stops and the tyres keep turning,
Pretty dang tough 🔥
That’s hard core stuff:). Man that’s cool cool cool 💯💯
Man that's pretty cool to bad you couldn't put those tires on the top shelf on that buggy would be sweet
I keep braking drive shafts on my gen 7 lol would theses fit my truck or any ideas witch ones to get
This also goes to show thag those cheap beadlocks and Axial transmission gears and cage can hold up to it as well!
I keep loosing u joint pins so now I bought the vitavon driveshafts....Is it just me or does the weight of the heavier drive shaft carry momentum longer after you let off the throttle? It seems like I have to let off the throttle sooner launching up hills.
I have two Ryfts (less then 6months old) that both also have loose u joint pins in the axle shafts....I can't find anything anywhere about how to fix or avoid this problem. They chewed into the plastic knuckle and I'm only lucky I haven't lost them. If anyone has any helpful comments relating I'd very much appreciate it.
I think they were the xmaxx paddle tires
🎉 WOW !! That’s epic
That was insane
Way rougher than planned.
the rc is good omg i really want the rc to be durable
Next will be a vitavon cage
If they made it I’d have it!
@@ExocagedRC haha 😄
Haha future u was awsome an those parts look like something great
Thanks!
With a million parts my udr is actually not breaking as much
Yeah right ✅
Brutality.
make the smt10 upgrade like this ryft so we can see great videos like dis but with a monster truck
The Ryft should not have survived...lightweight baby
About 10.5lbs
😂😂🤣😂😆 Omgoodness Epic!
😂
👍
But, but....facebook said vitavon is junk, and facebook knows it all.... ;-)
Moar
👍🏾👍🏾👍🏾
👍🤭😭😭
My problem with Vitavon product is for each axle housing you could buy a new RC for each link setup you've bought half a new RC. I understand it can cost a lot to upgrade an RC but at what point is $3-500 per upgrade just too much? It's getting to the point where it's killing part of the fun of the hobby, upgrading. Appreciate your content but you've become a Vitavon representative or are you only representing high end stuff because the rest is not worth your time? I can see why you need so many patreons.
Wow... uber cringe
You got that right
😁1👍
WOW !!!