How to Replace Liftgate Handle 07-14 Honda Fit
Вставка
- Опубліковано 12 вер 2024
- Shop for New Auto Parts at 1AAuto.com 1aau.to/c/29/M/...
In the video, 1A Auto shows how to remove and replace a rusty or stuck liftgate handle. The video is applicable to the 07, 08, 09, 10, 11, 12, 13, 14 Honda Fit.
🔧 List of tools used:
• Pocket Screwdriver
• Pry Bar 1aau.to/ods/1AX...
• 10mm Socket 1aau.to/oyf/1AX...
• 8mm Socket 1aau.to/oyf/1AX...
• Ratchet 1aau.to/oJy/1AX...
• Socket Extensions 1aau.to/oCq/1AX...
• Pick 1aau.to/odJ/1AX...
For More Info visit us at 1aau.to/h/bC2/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto
√ *Do it Yourself*
√ *Save Money*
I changed the latch thanks to this video and another one on YT. I could not get past removing the rear wiper arm, which was stuck. Therefore, the black trim with the logo remained in place. I managed to wiggle part of the old handle out of the hole where it normally rests when screwed in place, but the internal part of the handle (the crook part) was stuck as the gap it has to go through is a tad too small. I ended up using small pliers that I use for electricity and electronics works to cut through the internal metal sheet and bend it just enough to remove the handle. Once this was done, the entire installation was over in less than 5 minutes. If I ever have to change this handle on another Fit/Jazz, it would be over in less than 10 minutes. If it wasn't some clips breaking when either removing or putting back the interior trim, I would deem the operation simple and easy. Thanks a lot for this video.
Two bits of possibly helpful info on top of this
1) Taking off the wiper motor gives you better access to the clips, its only 3 bolts, so easy to do
2) When its cold you are more likely to break plastic. If you have to do it when its cold out, try using a heat gun around where the clips are (don't melt them)
Taking the motor off was very helpful, thank you for suggesting it!
Agreed, thanks for suggesting this. I was able to remove all clips without damaging them using this method.
Thank you so much for this video! I just changed the rusted latch by following your instructions. Besides being terrified that I would snap some piece off, it went smoothly.
+Sonia Marcoccia Thanks for the feedback, we are glad this helped you out! 1aauto.com
You give me the courage to just do it now!!!! Thank you Sonia! I can't live without stuffing my fit with stuff I find and I'm moving soon.
Cheers, Camille
Had a really tough time getting the wiper arm off, but ran out to get a Tie Rod End Puller for $15.99 at Advance Auto and it did the trick.
Thank you for the tutorial. I switched out the new part in 30 mins. I got the Honda part and installed it for under $80. Firestone was going to charge an absurd amount of money.
Awesome, thank you so much. I've gone 3 years with the hatch not opening. Now to attempt it.
While, not a Yaris owners problem, the Fit/Jaz does perform and handle much better, yes pun intended.
So will perform this repair, but instead of giving Honda a cent of money to replace a component that wasn't properly durable from the start (again, not a Yaris owners problem) will simply clean and apply waterproof dry lubricant to the original part.
Another great video guys.
Extremely clear instructions - will save us a pile of money. Thanks!
You saved me $500. Thank you!!!
awesome - fixed mine in about an hour using this video. I didn't have a prybar for the pins so i took a drumstick and after some finagling it worked!
Trying to pop those clips to release the tailgate garnish (aka the logo trim/handle cover) was a huge pain. Broke a few clips and busted off a tab from the back of the garnish. Do everything you can to pop this clips or you'll have to reinstall the garnish with fewer fasteners keeping it tight to the body.
Can we do something to stop future rust? Grease or something?
Great video, thanks! I wasnt able to get the wiper off without fear of snapping it so I left it on and jimmied the latch through the gap of loose black plate. I got a few small scratches, but hey the cars 15 years old and im no professional mechanic.
I just change one, on my girlfriend Honda fit 2009 Your video helped me a lot . I didn't have to remove the rear wiper
We have the same problem on our fit (2011) good info, thank you.
i was able to remove the latch without having to remove the black trim part in the back connected to the rear wiper
Thank you very much for the video.
Can you indicate the reference for this part?
Is this part even available at 1A Auto? Can't find a listing for it.
Awesome, thanks so much for the video! Replaced my wife's latch for less than 20 bucks. Can't beat that! 👍
Nice, thanks for sharing.
If you guys have the clips, please link to them for us!
Open the hole with a chisel just enough for the latch to slide out with out removing the trim and wiper. Then hammer the pin out, grind it down and wire wheel. Enlarge holes in the plastic handle part with drill bit. Grind sides of handle also. Reassemble with anti seize. Hammer the ends so they don't slip through mushroom it out a bit. Done feels like new will never rust up again. If it does ,it wouldn't get stuck because now everything is sloppy enough.
would have bought the part from you if the link brought me to the product page instead of a generic search result that doesnt have the part listed.
Thanks for the video! Any idea of it would be the same process for a 2015 Fit? Everything seems similar, but it does have a different design.
Thank you
My wiper blade seems stuck after removing the nut. Any advice would help.
Thanks! Changed mine tonight 🙂
WELLLLLL! That's the problem!! What a pain in the ass! I'm going to have to get a new handle but in the meantime my door won't latch and my interior light will not go out!!! I keep getting stuck at work with the dead battery!!! UGH!!!
THANKS FOR THE INFO! 😊
See if you can push the handle in toward the car before you close the door. This works for me, it's hard to do since all the rust but it might be worth a shoot
I had to buy a jumpstart power pack due to this. Now I just pop the hood and unhook the negative from the battery - because this hatch issue is also causing my alarm to go off randomly and run the battery down that way too. It’s SUPER FUN and is making my loads of friends in neighbouring apartments when it honks all night long. 🤨
Thank you so much for this video it made it so easy to replace the handle.
+Bruce Downs Thanks for checking us out! 1AAuto.com
There is one philips screw holding in the honda face plate. Look around the 3 minute mark. It is a metal scrrew ( philips)that screws into a plastic honda name plate.
+Dean Ward Thanks for the feedback!
Thank you.
How to replace the tailgate handle in a 2011 Pilot, How do I take out the garnish bolts?
Thank you so much!!!!!
What gloves are those ? They look super grippy
+Polar Zeus These are PT (performance Tool) These gloves can be found at www.1aauto.com/large-black-nitrile-%28powder-free%29-5-mil-disposable-gloves-box-of-100/i/1axss00002
Why can't I find anything on fixing a 2015. So frustrated. Guess I will give up and hand over 500 to the dealership🙄
That seems like a lot of bs for a little door handle.
First