How to Dress a Grinding Wheel | 3 easy ways
Вставка
- Опубліковано 23 лип 2024
- Three easy ways to dressing a grinding wheel on a bench grinder with DIY Grinding dresser:
00:00 Wheel face out of round
00:13 #1 Diamond Blade
02:23 #2 Spring Lock Washers
03:30 #3 Masonry Drill Bit - Навчання та стиль
Wow.
Nice effort in trying to help people out but wow. I definitely wouldn't recommend doing any of these methods. Dressing wheel tool and a solid base is the way to go.
Useing the diamond wheel to dress the grinder is a very good idea. I only watched the video, didn't listen to the sound track so you may have mentioned this. I would be very reluctant to dress the sides of the grinder wheel. Grinder wheels are not designed for ANY side loading. To much side loading and the wheel WILL shatter on you and chunks of it will be coming at you at very high speed. After all these years I still stand to one side and reach over to turn grinders on. I wait until it gets to full speed then move in line with the wheel to do my work. Still the diamond wheel is a good idea. I also liked the way you set up to avoid a mess. Well done.
👍 Yeppers if possible never stand inline , while true if it grenades it's going everywhere , but standing inline is just bad , like running a tablesaw always stand off to the side of blade . An avoid the cheap grinding wheels also , we had a kid who on his lunch break run up an picked a cheapie one . I really don't know what happened as I wasn't there at that end of The Shop , but man that thang came apart with a Hell'va racket fortunately he didn't suffer any long term injuries , The Shop Foreman really chewed his ass out .
I've used the worn carbide cutting tips from the Brake Lath as well , they do a great job on grinder wheels .
I just use the tool that was designed to do the job.
A lot safer.
Plus it only costs around $5
what tool? can you add a link? Thanks
Especially in a rush on a Sunday afternoon...
Thanks man - the split washers worked amazingly well for me! I have a 6" grinder with two stones and both had a big groove worn in the middle of the wheels. I had been looking to buy a tool for this but then I came across your video and decided to give it a go, but with LOW expectations. I mean it's so simple, how could it work better than a purpose built tool?? Well, 20 mins later I had two beautiful, square stones with ZERO cash outlay (had a bolt and washers already). You saved me $40+ and the time to go grab a tool for this. Amazing! And the other plus is that the rig I made with the washers did 2 wheels and look to be able to last for a few more clean ups yet!
Some tips if you're going to do this - make sure there's enough clearance on the bolt to allow the washers to spin freely and not too long a bolt to allow you move side to side across the face of the stone (so you wear the washers more evenly). The other tip is this will get Hot, so wear some rigging gloves or similar. 👍
I love the "but with low expectations"
There's a tool for that , it's called a grinding wheel dresser tool . Works very well for this . Just a FYI 😉
Yep. Its a must have item
He called his video " repair without any special tools". FYI
@@EvacuatorPro a grinding wheel dresser is not a special tool. It's a standard tool if you have a grinder.
@@frogsoda I’ve inherited a grinding wheel, but got no dresser tool. I’m still searching for a shop where I can buy one. So at least for me it’s not a “standard tool”. Until I find one, the tips in this video helps me.
@@bjondersson man everything he showed in this video is extremely dangerous, especially dressing the side of a grinding wheel. You shouldn't even use the side of the wheel much less dress it. Do what you want but these wheels can blow apart and if I'd does you will be sorry. Trust me seen it happen.
There is actually a tool made for dressing wheels,it can be bought at most hardware stores & welding supply stores !
Costs like a good set of carbide-tipped drills (unless you can get it as a cheap replacement part for grinders ofc but the pro stuff which is readily available over here costs that much) vs 1 old piece. And even if you buy the tool but you don't have the dressing harness for the grinder for any reason, the tricks here are still useful.
My wheel dresser (essentially some very hard abrasive on a stick) cost a couple of quid and works fine on small and large bench wheels. Leaves a completely square surface.
Must confess I'm puzzled why anyone would need the methods in this video.
Great ideas.Thanks for sharing.
2:55 right. i used the same idea, lock washers on a large screw driver, works for me. The diamond wheel, on angle grinder, new idea for me. Thankyou, sir.
I use regular flat washers. an old file works also
Thanks for the video! I gotta try soon!
Smart ideas!!! Thank you
Very informative video for Diyers like me. Will try this later
Now I have a use for all of my old masonry bits.
Красавчик!спасибо,вроде бы элементарные веши для технаря,но мне в голову не пришло что можно простым способом балгаркой с алмазным кругом править камень,гениально просто,мои похвалы автору!
... только круг не алмазный, а карбид-вольфрамовый, алмазный в10раз дороже стоит и править круг слишком накладно!!!
@@user-hi4sf2uj8w в обеходе подавляющая часть знают как алмазный,скажешь такое продавцу,он тебе ответит что не имеет такое,а на лавочке может лежать,так что я давно перестал придираться к словам и терминам,если суть ясна.
Excelente vídeo.. Gracias
En güzel ve yararlı videolardan biri.👍👍👏👏
Leave the power on! No need to run down the grinder as it's being dressed.
It’s Russia, cannot run two tools at the same time
@@joelhart9020 how does he have the vacuum on at the same time then?
@@joelhart9020 Ha ha!
Спасибо за идею! Лайк однозначно!
Weird, I just replaced my old dresser for one of those new fangled diamond coated wheeldressers off of ebay. It cost less than $10.00, is absolutely safe and took about 6 seconds to dress my nappy old grinding wheel. Even if I didn't get the "SPECIAL" tool, I wouldn't use this method shown here, I'd get a new $13.00 stone. Although it worked, I don't like bending the rules that far.
They obviously never seen a wheel blow apart before.
Great methods shown. The list of "chapters" with thumbnails is a great reference feature, much aporeciated.
C'est magnifique et merci pour l'idée
Wow! Its very useful information!👍
With UShM the Best metod. Thank you!!!
And good luck :-)
Thank you for sharing your video, the video is great and I learned something new today. From Australia.
Gute Ideen die einfach nachzumachen sind ich nehme immer ein Segment einer alten Diamantscheibe und schweiße mir einen Griff ran und nutze dies dann zum Abziehen der Schleifscheibe geht auch sehr gut
That's a great hack for straightening out your old crooked out of round grinding wheels
It can also make the wheel explode. The wheel is not made for sideways pressure
@@nicolasmiller-vachon4066 that makes sense also if there's a crack in the wheel and you try to push on the side of it I am sure that'll end up pretty badly too
Не очень понятно зачем делать старт/стоп. Круг отлично обрабатывается и при постоянном вращении.
У него просто мотор тухнет.
@@parikmag ))) а я не догадался!
Да вроде выключает...
@@vladimirrudenko4265 ну потому и выключает чтобы не облажаться ))
Это советские движки, у них сильный тяговый момент. Как бы не должен тухнуть.
Прикольно получилось. Не знаю, как на счёт техники безопасности (особенно сцена с гровер-шайбами) но выглядит убедительно.
Thank you
Poco tempo fa aquistai un utensile ravviva mola fatto con rondelle dentate... adesso grazie a te ho scoperto nuovi metodi per ravvivare pietre.
Второй вариант мне подойдёт. Спасибо большое!
Good to know. I'll use it. I dont quite understand the reason for on/off. Why not just leave it run to the finish?
Good video.
Nice shearing 👍
Когда диск от болгарки дороже точильного...
Не все можно сделать при помощи УШМ
Very good
Спасибо друг
Спасибо большое
Рисковый спец.
Перо с гроверами засунул между площадкой и камнем, это круто👎😶 так можно пальцев лишиться!!!
Да и сбоку камня нельзя точить!👎😶.
Опасно это!!!
Такие ролики НЕЛЬЗЯ использовать как руководство к действиям!!!
Diamond wheel dresser for me, all day long.
Блин ну есть ведь спец инструмент для этого чо огород городить и гробить дорогой алмаз по бетону?
Part of this is scary.
One thing for sure, that is a good way to start a fire in a vacuum cleaner.
Thanks. Chris
Боковую нагрузку к диску УШМ - да он бессмертный!
Ну он же щиток надел!)))
ممتاز
Благодарю вас
Вроде специальные камни есть для правки и вскрытия дисков
Да, есть алмазные карандаши и правИла, а также шарошки, но я решил показать как обойтись без них - для разовой правки самое то, если вам надо выровнять камень раз в несколько лет
А алмазным карандашом не проще? И не каких хреновин лепить не надо, болгаркой тоже можно,но это для тех кто не ищет лёгких путей
Наверное проще. Если он есть.
У меня например, есть несколько алмазных резцов. Я один заделал в бронзовую трубку и этой штукой выравниваю круг.
А болгаркой тоже неплохо. И не обязательно даже алмазным кругом. Обдирочный диск вполне справляется.
You can grab a rock from the garden and use a steady rest in a pinch also 😗
Я ровняю проще, кусок сломанной рессоры и на включённом моторе потихоньку не спеша слегка касаясь и камень как новый, можно также старым напильником толстым тоже не плохо ровняет
۳۳۳۳۳۳۳۳۳33۳۳۹۷۷۷۹۷۷۹۷۹۹۷۹۹۹۹۹۹۹۷۷۹۹۷۹۹۷۷۹۷۹۷۷۷۷۷۹۷۷۷۷۷۷۹۷۹۷۷۹۷۷۹۷۷۹۷۷۷۷۸۸۷۸۸۸۸۸۸۸۸۸۷۷۷۷۷۷۷۷۷۷۷۷۷۷۷۷۸۸۸۸۸۸۸۸۸۸۷خخ۸ح۹حححححححححححححححححححححححححححححححححححححححححححححححححححححح۹ححححححح۹۹۱ح۱۹۹ح۱حححح۹۹۹۹ح۹۹۰حححح۹۰ح۹۹۹حح۹۹ح۹ح۰حححح۹۰۷۷۸۸۷۷۷۷۷۷۸۸۸۸۸۸۸۸۸
Отличная идея, а как алмазный круг себя чувствует?
Grinder from 1986 made in USSR. I have exactly the same. It dance a lot on the table. The body is too thick and therefore the diameter of the stone should be always a bit bigger. I dont use it for last few years.
Без специальных приспособлений))
👍😂😂.
Я видел на камне сбоку пластины для равновесия. У меня тоже такие.для чего они?не пробовал регулировать их.или лучше не трогать?
Для балансировки диска, путем их смещения по отверстиям.
@@user-kc5jv7mr5x это я знаю.но ничего не получается только хуже.я их снял вообще
GOSTEI. IMPORTANTE
Parabéns valeu muito 👏👏👏👏👏👏
Blade ka name kya hi
Ну уж очень без специальных приспособлений.
С помощью УШМ - зачёт👍
А вот с гроверами - опасно. Так лучше не делать.
Согласен. Я даже подумал что с гроверами сразу зажмёт.
А почему именно гроверы использовались?
@@silentcooler4160 гроверы имеют закалку, а например шайбы не имеют, поэтому они "мягкие".
@@silentcooler4160 хорошая закалённая сталь, не сразу стёсывается
@@silentcooler4160 потому что нашлось под рукой и полезло +- на сверло. А так самая обычная шарошка делается из любых шайб , чтобы свободно шевелились заьсчет этого ВЫКРАШИВАЕТСЯ зерно , из-за удара шайб по кругу , а так еще есть спец Карандаши для правки стоят копейки уж точно дешевле диска на ушм
The real question is, how did it get that wonky in the first place? Especially on the sides.
Brand new wheels come that way. At least the cheap ones do. I bought one from Harbor freight and had to do the same as this guy is doing.
Excelentre trabalho.
When does the "easy" part start?
болгаркой с диском - думаю самый приемлемый способ
Вот они и встретились))
But for the people that can't just walk out and buy new tool right away this is a good alternative
Я где-то слышал, что можно еще подправить обломком другого круга, часто попадается в хозяйстве. Но успех сильно зависит от материала круга и обломка.
...править не получится, а вот почисть- самое то!!!
Круг засаливаться будет. Зерно 60 превратится в зерно 100, а то и выше. И точить перестанет как надо. Просто шлифовать будет. Проверено на производстве.
У меня нет заточного станка, зачем я это смотрю, притом до конца.
Если ты порядочный мужик, то теперь должен купить его:)
Как алмазные диски и болгарки появились в продаже, с тех пор так равняю!!!
Yes you can buy dressing tools ,but what AH would want to when you can do it on the cheap. dressing tools are expensive and only last 5mins So tomorrow morning early you can have a lovely straight wheel .see
Второй способ правильный.Алмаз превратит заточкой круг в шлифовальный
Это почему же? Алмаз чудом изменит зернистость камня???
@@13cheebo он срежет зуб зерна и сделает его лизуном
@@13cheebo А причем тут зернистость? Или не слыхали о черновой шлифовке?
У таких камней склейка зерен не на высоте. Единственный способ сделать его "лизуном" это поточить на нем албминий или дюраль, забить пространство между зернами укрепив попутно посадку их внешнего слоя. Вот так да. А алмазом не испортишь, следующая обработка черного метала все поставит на свои места.
Алмазный карандаш для этого есть
Why on and off?
Подручник для чего дан? Для красоты?
Надо деталь хорошо прижимать к подручнику и не давить на камень, не держать деталь на одном месте, плавно водить слева направо, справа на лево, тогда и не будет образовываться эксцентриситет на камне, будет равномерно изнашиваться камень, не следует ломики и топоры на весу затачивать как некоторые рукожопы делают. Расстояние от камня до подручника должно быть минимальное.
И тогда не придется ровнять камни.
Томского завода точило?
Не понятно нафига надо постоянно включать и выключать станок при правке камня?
The angle grinder diamond disc isn't flat or straight.
спасибо за ролик. С уважением к Вам и вашему каналу «Вторая жизнь ПЕТ бутылок».
А зачем останавливать во время правки?
Ah, yes… the old split lock washer to be used to replace the worn down star rings on a grinding wheel stone dresser. I use the external spiked lock washer, also. I didn’t see you around, 50 years ago?
Для правки круга есть специальный камень.Называется АЛМАЗОН.Кто не работал на производстве,тот никогда не видел его.У меня до сих пор он есть на даче.
Хотя и этот метод подходит.
Or I could just but a stone to dress the wheel hell of a lot easier.
А ещё проще ровнять куском от образивного круга который давно валяется где - то среди всякой не нужной мелочи Таким методом я уже польззуюсь больше 20 лет Главное чтобы кусок образива был мелкозернисым и чтоы было соблюдение правил техники безопасности (ЗАЩИТНЫЕ ОЧКИ - ДЛЯ ГЛАЗ И РАСПИРАТОР - ОРГАНЫ ДЫХАНИЯ!!!) ВСЕМ ЖЕЛАЮ УДАЧИ!!!
От этого круг засаливается. Ровнять надо алмазным роликом. Или карандашом.
"Хитёр, матёрый..."
:))
What happened to that wheel anyway 😮
1:21 looks like you hate that finger isn't it?
Спецы пришли к тому что главное хороший круг.потом макс.точная посадка на вал с прокладками и на эпоксидку.потом ровнять.сдвух сторон
А зачем выключаете вращение наждака, когда правите?! Правят на включенном и болгаркой и шарошками))
Алексей, выключаю только при правке с помощью УШМ для безопасности
@@MazayDIY для безопасности экраны от абразива, очки/маска и тп. А выключением своим вы основной принцип нарушаете - два тела вращения под углом друг к другу исключают ошибки нежесткого контакта.
На больших оборотах точно не выровняете, сам мотор трясётся и выберает не там где надо, я прошу друга, чтоб он крутил наждак о другой камень рукой медленно, это я прошёл. Так же на машине неотболонсированое колесо, казалось, что где меньше изношено будет бить об асфальт и уровняется, но не тут то было изнашивается где уже изношено
А если через регулятор напряжения?
А может лучше поменять на новий камень.
Не ужели так дорого купить правило ?
There’s a tool for that….. works great
Я также болгаркой правлю, но не выключая нождак... Не очень понял для чего вкл/выкл
На сколько понял, наждак от перегрузки останавливается.
@@petrovich5945 такой наждак куй остановишь болгаркой))) имеется такой. В нём дури с запасом, хоть ломы титановые точи.
Боится повредить круг болгарки
@@user-qd4lz3rw6b м.б. м.б.
@@petrovich5945 нет, там тяговый момент просто бычий..его не остановишь)). Да ещё и с двойной обмоткой, дополнительно разгонная сделана при утоплении кнопки. Многие не знают..вещь классная, СССР. На оборотах больших может вибрировать и бить сам вал. Поэтому точит на малых, с выключением. Есть модели таких моторов, скажем, не слишком оборотистые, а есть высокооборотистые, на которых есть риск разрыва камня, если тот плохого качества. Вот и не рискует..
Без специальных приспособлений... Болгарка, алмазный диск, пылесос, струбцины - это не специальные приспособления?))
Да ладно. А что, нутриометр с набором алмазных брусков чаще встречаются?
👍😂😂
My grandpas sharpened axes and lawnmower blades never seen them ever dress the wheels 😏
You made that more expensive and harder than it needed be. For just a few bucks you can get a wheel dressing tool from the hardware store.
I'm at a loss as to exactly how a wheel can become lopsided, unless pieces were break off
Exactly never dressed one didn’t know of it both grandpas never did
@@jameschester3986 I could see needing to do some minor flattening if you aren't smart enough to not just grind in the same spot constantly, or if you were using the side of the wheel, which you aren't meant to do anyway (on most general purpose wheels). But this one he did had a huge dip in the wheel that couldnt have been made with the grinder powered on, even if you just jammed a piece of tungsten in there really hard, you cant just wear down a spot without wearing it down along the entire radius. If it jammed hard enough to break a piece out and come to a stop, i suppose that could be it, or if it was a manufacturing defect where part of it cracked off idk lol
Why not use a dressing tool?
Он правится куском от абразивного круга, держа в руках
Use a wheel dreser
Толково. Только диск лучше какой нибудь левый
Есть специальная правка и она продается!
Название видео читали?..
Любой негодный алмазный диск отлично правит камни.
There are way easier and therefore better ways to dress a grinding wheel that uses the power of the bench grinder not having to turn it on and off. They certainly don't require another electric grinder and still achieve great results. For me this is a great example of over thinking something.