Thanks for the video, Can you please tell if I want to make the Start Unloading I need to energize the solenoid CR3 (25%), how much time is required to hold this solenoid ? as I understand, for unloading I can de-energzie the motor and apply voltage only to the CR3 solenoid ?
Sir just to ask if sequencing of solenoids percentage is just for start up only?and after few times 100 percent should be maintained in 10seconds open close timing?
Very nice explanation thank you very much if you could do your videos with translation to English like this one or if by the cc button which is written translation to English it would be very appreciated thank you again
من انگلیسیم متاسفانه زیاد خوب نیست ولی خیلی استفاده کردم اولا اگر میشه زمان خاموش وروشن بودن بقیه شیرها مثل ۱۰۰ درصدو رو نیز برامون بگین دوما اگر ممکن فارسی هم بگین
hi there is not a list for abnormal situation that cause noises. it has really wide range of cause such as abnormal superheat, wrong oil type, contamination, wrong capacity control....
Thank you for the explanation, introduce my name is sarjono where I work there a compressor Bitzer for chiller Climavineta often migrated oil, can you explain to me, why did it happen?
Thank you my name is mehdi asgari. There are three possible phenomena. First, the expansion is not working properly, which is probably a rejection. Second the heater does not work properly which is probably a rejection .Third, flash gas is produced due to the capacity change that produces foam on the oil surface
hello my name is mehdi. migration in bitzer screw compressor create by low superheat, low subcool and low condensing temperature. if fome of oil is upper side of oil in sight glass. its not important
Thank you sir,coming clearly voice.properly understand all
Thank you sir very good explanation
Thank you for your good explanation👍
Thanks nice explain make more videos in English full information we can understand
Thanks for the video, Can you please tell if I want to make the Start Unloading I need to energize the solenoid CR3 (25%), how much time is required to hold this solenoid ? as I understand, for unloading I can de-energzie the motor and apply voltage only to the CR3 solenoid ?
Sir just to ask if sequencing of solenoids percentage is just for start up only?and after few times 100 percent should be maintained in 10seconds open close timing?
Thnxs more
What model of CLP can i use with this compressor?
Good explanation
thanks a lot for sharing these usefull informations
your welcome
if the oil lubrication is reduced when running. and the oil will return suddenly at an unspecified time. what do i need to do
Nothing you can do this phenomenon in screw compressor not dangerous but in some kind of reciprocating compressor can be
Nothing you can do this phenomenon in screw compressor not dangerous but in some kind of reciprocating compressor can be
Can it run 25 % for long time 3 hrs ?
It can but it's not correct
Es normal que se presente escarcha en compresor en la parte de sucesión..?
Nice good.. semiharmetic compressor video
How much oil injection pressure will there be during 50, 75 and 100%? And how is this pressure achieved?
Thanks In advance.
It's a good movie and I will show in next month
Very nice explanation thank you very much if you could do your videos with translation to English like this one or if by the cc button which is written translation to English it would be very appreciated thank you again
Sure
@@mehrespand_ir I watch all your videos I wish I could understand everything thank you for what you are doing
Boa noite amigo,
Uma pergunta : a válvula slide se movimenta com a pressão do gás ou do óleo, obrigado.
Hello
Please English.
@@mehrespand_ir,
Goog evening Sir, i would like to know if the
Slide valve moves by gás or oil pressure,
Thank you.
Se move pela pressão de óleo!
Muito obrigado amigo 👍🇧🇷
من انگلیسیم متاسفانه زیاد خوب نیست ولی خیلی استفاده کردم اولا اگر میشه زمان خاموش وروشن بودن بقیه شیرها مثل ۱۰۰ درصدو رو نیز برامون بگین دوما اگر ممکن فارسی هم بگین
Pl kindly explain the electrical schematic diagram of this model. Expecting soon.
Me pueden hacer una traducion sl español por favor tengo problemas con uno igual que no quiere elevar su revolucion
Hi sir what type of abnormal noices are getting from screw compresos
hi there is not a list for abnormal situation that cause noises. it has really wide range of cause such as abnormal superheat, wrong oil type, contamination, wrong capacity control....
Thank you for the explanation, introduce my name is sarjono where I work there a compressor Bitzer for chiller Climavineta often migrated oil, can you explain to me, why did it happen?
Thank you my name is mehdi asgari. There are three possible phenomena. First, the expansion is not working properly, which is probably a rejection. Second the heater does not work properly which is probably a rejection .Third, flash gas is produced due to the capacity change that produces foam on the oil surface
hello my name is mehdi. migration in bitzer screw compressor create by low superheat, low subcool and low condensing temperature. if fome of oil is upper side of oil in sight glass. its not important
Thank you, a good lesson, but is it possible to translate it into French or Arabic? Thank you
😀
درود بسار عالی .برنامه زبان فارسی هم دارید .
درود بله کانال اینستاگرام ما را دنبال کنید
Thank you
Your welcome
@@mehrespand_ir, better than 140 HP
Can upload
your accent was iranian..
yes
Thank you for the video really appreciate the information I have a question is CR for constantly on what can happen?
Al 131 falt