Thanks for the encouragement. As of now, I am very busy with school stuff and can't make more videos. Maybe later! I hope you can find answers to your questions by going through my videos which correspond to your requirements.
thanks for the tuto, but the stress i not uniform as you said, in order to plot the stress distribution within the beam we have to active the 3D plot as you did for displacement
How can we find displacement in X-direction when load applied in Y-direction alone. Even though load applied in Y-direction, in large displacements there may be chance of sliding of nodes in X-direction. How could we find them? help sir
Thank you very much!! its a very good tutorial. Sir i have a confusion. Pressure on line is right? or Pressure on Beams is right? when to use pressure on line and when to use pressure on beam? your response will help me very much thank you
Thanks for the tutorial,,,Can you help me and show me how to attach springs in three directions on the beam188 in ANSYS APDL. Am doing research on stress analysis of buried oil pipelines
how can i configure 10 different sections? i have a ship with 10 sections and I need to configure the area, Izz and Iyy, and I could not configure them,tx
Hi Mandi, Thanks for your tutorials.I am going to design portal from using cold form lipped(back to back) channel section for medium size warehouse. This is the one of the section I am using for my design.(250x75x20) thickness is 1.6.Could you please explaine that how this cold form lipped channel behavior in ANSYS 3D. Thanks
prestressed concrete use soild 65 to put steel reinforcement which i think link10 . put its hard for me im new in this filled i hope you response to me
You are my hero!
Thanks for the encouragement. As of now, I am very busy with school stuff and can't make more videos. Maybe later! I hope you can find answers to your questions by going through my videos which correspond to your requirements.
Awesome tutorial! Helped me a lot. Thanks!
very good tutorial - thank you. Nicely presented & clearly explained :)
wowwwwwwwwwwwwwwwwwwwwwwwwwwww........I love your explanations thank you sir you r simply awesome thank you.. please upload more videos
thanks for the tuto, but the stress i not uniform as you said, in order to plot the stress distribution within the beam we have to active the 3D plot as you did for displacement
How can we find displacement in X-direction when load applied in Y-direction alone. Even though load applied in Y-direction, in large displacements there may be chance of sliding of nodes in X-direction. How could we find them? help sir
I have so much to say, but just a little here... Thanks so much
Thank you very much!! its a very good tutorial.
Sir i have a confusion. Pressure on line is right? or Pressure on Beams is right? when to use pressure on line and when to use pressure on beam?
your response will help me very much
thank you
thanks for the video...can u please tell me how to change the direction of pressure?
thanks for your learnings video i hope you upload how to make prestressed concrete beam and quastion can ansys do seismic earthquake test on it
Thanks for the tutorial,,,Can you help me and show me how to attach springs in three directions on the beam188 in ANSYS APDL. Am doing research on stress analysis of buried oil pipelines
please do the beam analysis of simply supported with beam element 189
it's awesome:) however i have a question. Is the unit MPa and mm ? The EX and pressure is used with the unit Pa
Very usefull !
how can i configure 10 different sections? i have a ship with 10 sections and I need to configure the area, Izz and Iyy, and I could not configure them,tx
Hi Mandi,
Thanks for your tutorials.I am going to design portal from using cold form lipped(back to back) channel section for medium size warehouse. This is the one of the section I am using for my design.(250x75x20) thickness is 1.6.Could you please explaine that how this cold form lipped channel behavior in ANSYS 3D.
Thanks
Sir, may I know how to model a cylinder Tensairity beam by using this software? I'm new in using this software. Thank you very much.
Mahdi Farahikia, may I know how to draw 2 or more different dimension section in APDL? Very appreciate if you can help me. Thank you very much
prestressed concrete use soild 65 to put steel reinforcement which i think link10 . put its hard for me im new in this filled i hope you response to me
Sir, can you please put a tutorial on curved cantilever beam like similar to cesna-150?
where is beam3?
Please,help me