How To... Mirror alignment.

Поділитися
Вставка
  • Опубліковано 10 гру 2024

КОМЕНТАРІ • 20

  • @kylewheeler1161
    @kylewheeler1161 Рік тому +1

    ABSOLUTELY SPOT ON (PUN INTENDED)!! Excellent tutorial and a must for anyone having mirror alignment issues like myself. I don't know how you could have made it any better! Hats off to you and you're an asset to the laser world for sure!

  • @davehastings9245
    @davehastings9245 4 роки тому +3

    OMG!! Where was this video when I was trying to figure out how to align my laser? LOL It took over a week, several hours a day, multiple you tube videos, and a lot of of swearing to finally get it thru my old head! Wow this has to be the BEST video on laser alignment out there to date. Kudos to you sir, very well done! I will recommend this video to anyone/everyone having problems aligning their laser.

    • @HouseOfLasers
      @HouseOfLasers  4 роки тому +1

      And this is why we do what we do
      Thank you!!

  • @mysteryck13
    @mysteryck13 4 роки тому +1

    Excellent. Thank you Chris and great job!

  •  Рік тому

    Thanks!

  • @ericlandrum2436
    @ericlandrum2436 3 роки тому

    great video I'm in full study mode until my thunder laser arrives!!

  • @Taran-d.B.23
    @Taran-d.B.23 3 роки тому

    This Combining Lense Setup for the visual Laser is great 👍🏼 can i buy it somewere seperare? Because my Visual Laser is just screwed to the nozzle and not alines with the true laser. Thanks

  • @gpentsas
    @gpentsas 3 роки тому

    Hello and thanks for the very informative video.
    I understand that the combining lens with its holder and assembly comes with the specific laser machine? Any ideas where I could source such a combining lens for a DIY assembly?
    Thanks

  • @GaryGraham66
    @GaryGraham66 4 роки тому

    Slightly off centre is better than dead centre, this allows you to rotate the mirror if it gets burnt. The main thing is that it hits the same spot on mirror 3 all over your bed.
    I wish I had a red dot on my laser lol a damn sight easier.

  • @karvtek
    @karvtek 3 роки тому

    Great video. Thank you. Have you tried the reverse alignment tool from AP?

  • @whynotcnc8828
    @whynotcnc8828 3 роки тому

    thanks

  • @SaintTunaTTV
    @SaintTunaTTV 3 роки тому

    Hey there. Thanks for the helpful tutorial!
    Trying to get my laser aligned. I aligned the red dot and beam perfectly to mirror 2. When I pulse the beam to the third mirror, the laser pointer is center but the beam fires about 2 mm higher than the pointer.
    How can I correct that?

    • @HouseOfLasers
      @HouseOfLasers  Рік тому

      you have to move your pointer typically. this is not a one mirror adjustment.. you have to fine tune along the way

  • @quochaonguyen1732
    @quochaonguyen1732 3 роки тому

    How to maintain the belt?

  • @bgauweiler
    @bgauweiler 2 роки тому

    Has anyone seen an aftermarket upgrade that would allow you to add the red pointer as shown in this video to a "Chinese" 100W laser?

    • @HouseOfLasers
      @HouseOfLasers  2 роки тому

      You’ll need the pointer and combiner lens
      I think they make a kit. Check cloudray you may have to change out mirror 1 and it’s holder

  • @monavieforal
    @monavieforal 3 роки тому

    Good job. But not everyone has a red dot pointer. Be nice to have a video without the red dot.