Hi Brian, I am hoping you can help. Larry at PDQ is doing a full rebuild of my old ZRX11, 1109 kit etc. I need a speedo drive as I am putting a Dymag front wheel. I think you have one for a VFR? I am running a Greg Couch countershaft sprocket cover at the moment. Any ideas or help you could provide would be greatly appreciated. BTW, love the videos they have inspired me to rebuild the old girl.!
Yes., but you also need the Scott Stites Pulse performance adapter plate that replaces the one on the Couch cutaway sprocket cover That plate is machined specifically to mount the VFR speedo drive too.. He did a run of them as a group buy on the ZRXOA forum a number of years ago as per a request from us.. The plate also came with a Coupling adapter that had a rubber sleeve that went into the counter shaft the front sprocket is fitted to.. This whole assembly is then fitted in place and connected to the speedometer by a CB 1000R cable since it is the only one long enough to reach and link into the VFR speedo drive..(pretty sure that is the correct one...) Not sure if any of these parts are still available since it was a number of years ago and I bought two for both my ZRX's since I was running this conversion...,and they were produced to order for a limited run... Have a look at my two ZRX videos (The 05 and the 01 and you will see the setup I am describing..)....because without the replacement Pulse Performanance plate and coupling you cannot mount the VFR drive...,or connect it to the counter shaft... Hope this helps....,oh and glad you are enjoying and following along with the engine upgrade/rebuild videos.. Cheers and God Bless BG.
@@brianwells5258 Thanks Brian, yes that is a clever set up. Alas its not available anymore. Reckon I will stick with the stock well then! Thanks again!
Fascinating video, thank you Brian 😊👍
Thank you so much....,
Great to have you still tuning in and following along...
God Bless
BG.
Hi Brian, I am hoping you can help. Larry at PDQ is doing a full rebuild of my old ZRX11, 1109 kit etc. I need a speedo drive as I am putting a Dymag front wheel. I think you have one for a VFR? I am running a Greg Couch countershaft sprocket cover at the moment. Any ideas or help you could provide would be greatly appreciated. BTW, love the videos they have inspired me to rebuild the old girl.!
Yes., but you also need the Scott Stites Pulse performance adapter plate that replaces the one on the Couch cutaway sprocket cover
That plate is machined specifically to mount the VFR speedo drive too..
He did a run of them as a group buy on the ZRXOA forum a number of years ago as per a request from us..
The plate also came with a Coupling adapter that had a rubber sleeve that went into the counter shaft the front sprocket is fitted to..
This whole assembly is then fitted in place and connected to the speedometer by a CB 1000R cable since it is the only one long enough to reach and link into the VFR speedo drive..(pretty sure that is the correct one...)
Not sure if any of these parts are still available since it was a number of years ago and I bought two for both my ZRX's since I was running this conversion...,and they were produced to order for a limited run...
Have a look at my two ZRX videos (The 05 and the 01 and you will see the setup I am describing..)....because without the replacement Pulse Performanance plate and coupling you cannot mount the VFR drive...,or connect it to the counter shaft...
Hope this helps....,oh and glad you are enjoying and following along with the engine upgrade/rebuild videos..
Cheers and God Bless
BG.
@@brianwells5258 Thanks Brian, yes that is a clever set up. Alas its not available anymore. Reckon I will stick with the stock well then! Thanks again!
@@chriscarbaugh3936 OK..,no worries.,may I wish you every success with your project..
BG
cant the dampeners go in between the slots. they look like they are suppose to.
They are fitted correctly as shown.....
BG.