How can anybody dislike this video. My guy explained throughly, good video quality & wasn’t mumbling the whole video. You helped me tremendously! Keep up the good work! Thanks for info bro 👍
So helpful! I just swapped out a damaged door and had to swap over the handle, window, mirror, speaker. I would have been so confused trying to put the trim back on but it wasn't so bad with this video.
ThanKs alot for your videos I own a tinting business myself and appreciate you. It way easier to pop panals to get a good bottom load on the film. Again appreciate you
Does anyone know where I can buy a replacement for this specific door handle? My current door handle is peeling and I want to replace it, but I can’t find the part anywhere 😢
So anyone about to comment I did this and now the doors won’t open (I did the same thing 😂) don’t pull your seat out either just remove the 7 mm near the door handle and it’s going to take force but pull the top of the door till the clips come out then take a pair of needle nose pliers and give the line a tug and keep trying to open the handle and then the door will open. The problem was that I didn’t clip the line back in the proper spot which caused slack and wouldn’t activate correctly, I hope this helps
I just so happened to tint my windows and the cable to the door handle disconnected when the door was closed. Any ideas how I can get to that cable with the door panel being 1 whole piece and the door is shut? Im thinking of trying a hanger tomorrow but looking at this video that may be hard and i dont wanna cut thru the door i just got the car, any ideas anyone?
@@raiderman28 Ah, that explains some things: I found 3 torx screws that were holding it in place: 1 on the interior side of the door frame and 2 hidden under the window seal. But even after removing all 3 screws it still won't come out. I figured it must either be adhesive or something like double-sided tape preventing it from coming out. I'll keep investigating. Thanks though.
It will be very very difficult to remove the door panel to get to the inside of the door. I usually recommend pulling in the front seats from the opposite door to make room. You also want to disconnect the battery just before unplugging any yellow harnesses under the seat, if it has them. This are air bag plugs and you don’t want to unplug them while the battery is hooked up. It can bring on an air bag light. Once you have the seats out of the way, start to take apart the door panel and try to get it off. You might want end up damaging the door panel alittle in the process, but you need to get it off, to see why the door won’t open. Once the panel is off, hopefully you can tug on the cable to open the door, make sure the door is unlocked. Good luck
Can anyone please show how to insert the door handle on this car? It has a wire for keyless entry and I don’t know how to insert the wire because there’s zero videos on UA-cam.
Sounds like you didn’t attach the door handle cable correctly or door lock. You created a pretty big problem. Your going to have to remove the door panel again. But in order to do that you need to open the door. Without the door being open, your going to have to remove both front seats through the the opposite side of the vehicle. Make sure the car battery is disconnected, because some seats have air bag lights , and you can trigger them. So you want to make sure to move the seat back and forth and take off bolts, but do not disconnect wiring, until battery is disconnected. Then remove one seat then the other. This way you have room to remove the door panel. Hopefully you don’t break anything taking panel off. Once you get panel off, you can try and see whats not connected or if a cable is broken. Did you try hitting the remote unlock button and then open the door from the outside???
Trying pushing the unlock button on the drivers door or passenger switch. Hopefully that will work. Make sure the rod is coming out of the hole on the top of the door panel
On these 2016-21 malibus do you by chance know if the door lock switch has do be removed without having to remove the plastic welds from the housing bracket?
I just did this, having someone to help is a big plus. Unlike other cars, the window isn't bolted in but has clips. I lowered the window most of the way, pulled the clips a bit apart and the window pops out. Once you have the detached window out a bit, tilt it to one side or the other until it is free of the tracks on the sides.
Does anyone know the name of that little “panel” at the very beginning of the video inside the interior door handle im missing it on my Malibu and I’ve been searching for replacements but I can’t find the name or anything
If you remove the one for the rear door, it has a part number on it. I believe the front and rear door access panels are interchangeable ( so they use the same part numbers
WHY chevy make there tin like doors so complicated to take off.... Ford is easier to deal with.. Christmas 🎄 that mess up when you pop the door off and just replace them....LOL
Great video Raul - thanks 👍
How can anybody dislike this video. My guy explained throughly, good video quality & wasn’t mumbling the whole video. You helped me tremendously! Keep up the good work! Thanks for info bro 👍
Appreciate the kind words Ronnie
So helpful! I just swapped out a damaged door and had to swap over the handle, window, mirror, speaker. I would have been so confused trying to put the trim back on but it wasn't so bad with this video.
Very helpful , thanks I actually installed a panel without removing window seal ,what a pain in the a.. to install, now I know there is an easier way!
ThanKs alot for your videos I own a tinting business myself and appreciate you. It way easier to pop panals to get a good bottom load on the film. Again appreciate you
yes sir. thats why i make videos, to help our jobs be easier.
This works from 2021-2023 Malibu. I ended up buying a package of red clips from dealership for further panel removals
Does anyone know where I can buy a replacement for this specific door handle? My current door handle is peeling and I want to replace it, but I can’t find the part anywhere 😢
@@Rose-dy1xi probably only at the dealership. The vehicle is too new.
Right on brother
This is really helpful
So anyone about to comment I did this and now the doors won’t open (I did the same thing 😂) don’t pull your seat out either just remove the 7 mm near the door handle and it’s going to take force but pull the top of the door till the clips come out then take a pair of needle nose pliers and give the line a tug and keep trying to open the handle and then the door will open. The problem was that I didn’t clip the line back in the proper spot which caused slack and wouldn’t activate correctly, I hope this helps
I just so happened to tint my windows and the cable to the door handle disconnected when the door was closed. Any ideas how I can get to that cable with the door panel being 1 whole piece and the door is shut? Im thinking of trying a hanger tomorrow but looking at this video that may be hard and i dont wanna cut thru the door i just got the car, any ideas anyone?
You should be able to unlock it from the outside with a key or remote and still open it from the outside.
Great video 👍 , thanks
so helpful!
Great video! Do you know how to remove the black plastic B-pillar trim on the outside of the front door(s) for the 2021 Chevy Malibu?
Sorry, i do not.
Come to think of it, most of those have double sided tape from the manufacture. Many people wrap them or have them repainted
@@raiderman28 Ah, that explains some things: I found 3 torx screws that were holding it in place: 1 on the interior side of the door frame and 2 hidden under the window seal. But even after removing all 3 screws it still won't come out. I figured it must either be adhesive or something like double-sided tape preventing it from coming out. I'll keep investigating. Thanks though.
My door latch came undone after i closed the doors. Won't open inside or outside
It will be very very difficult to remove the door panel to get to the inside of the door. I usually recommend pulling in the front seats from the opposite door to make room. You also want to disconnect the battery just before unplugging any yellow harnesses under the seat, if it has them. This are air bag plugs and you don’t want to unplug them while the battery is hooked up. It can bring on an air bag light. Once you have the seats out of the way, start to take apart the door panel and try to get it off. You might want end up damaging the door panel alittle in the process, but you need to get it off, to see why the door won’t open. Once the panel is off, hopefully you can tug on the cable to open the door, make sure the door is unlocked. Good luck
Can anyone please show how to insert the door handle on this car? It has a wire for keyless entry and I don’t know how to insert the wire because there’s zero videos on UA-cam.
I followed these instructions & it worked out, but now that I put it back on I can’t open the door from the inside or outside? Any advice?
Sounds like you didn’t attach the door handle cable correctly or door lock. You created a pretty big problem. Your going to have to remove the door panel again. But in order to do that you need to open the door. Without the door being open, your going to have to remove both front seats through the the opposite side of the vehicle. Make sure the car battery is disconnected, because some seats have air bag lights , and you can trigger them. So you want to make sure to move the seat back and forth and take off bolts, but do not disconnect wiring, until battery is disconnected. Then remove one seat then the other. This way you have room to remove the door panel. Hopefully you don’t break anything taking panel off. Once you get panel off, you can try and see whats not connected or if a cable is broken. Did you try hitting the remote unlock button and then open the door from the outside???
On this Malibu do you have to remove the door panel to replace the door check ?
I have no idea. I tint windows, so i have to remove the panels to tint the windows
Yes
Took off the rear door panels and now the doors wont open, tried opening them from the inside and outside and nothing… any advice?
Trying pushing the unlock button on the drivers door or passenger switch. Hopefully that will work. Make sure the rod is coming out of the hole on the top of the door panel
great video thanks
Awesome! Thank you, thank you!
Your welcome!!
Nice work on explaining this.
Thank you
Great video, thank you!!!
On these 2016-21 malibus do you by chance know if the door lock switch has do be removed without having to remove the plastic welds from the housing bracket?
Not sure. Have not taken that area apart. Usually the actual switches should come off , just a pain to take out
Can I just pop the top on these like Chevy trucks??
On the chevy trucks you can, but on these i have tried to pull back and they are super hard and have not been able to.
@@raiderman28 you just need two tools when prying Jeff Welch does them daily....he knows his stuff....join these group tons of information....
@@raiderman28 use one tool to pry and metal screw driver on top with pressure to pop clip....
@@JBIRD575 i gave actually remove some of the older chevy cars with 2 tools, but found it a bit easier to do it this way for me.
@@JBIRD575 that how i doe the older ones. Can seem to see the clips on these newer chevy cars. Thats why i have done it this way.
شكراً جزيلاً
I wish i knew what you are saying
I need to replace back passenger window so is there anything special I need to know before starting? Please help
I don’t know, because i have never removed the window before, just the door panel …sorry!!
I just did this, having someone to help is a big plus. Unlike other cars, the window isn't bolted in but has clips. I lowered the window most of the way, pulled the clips a bit apart and the window pops out. Once you have the detached window out a bit, tilt it to one side or the other until it is free of the tracks on the sides.
jUst got my windows tinted and now my rear doors wont open. ANything to help with that?
Wont open from the outside?
Does anyone know the name of that little “panel” at the very beginning of the video inside the interior door handle im missing it on my Malibu and I’ve been searching for replacements but I can’t find the name or anything
Interior door handle access panel
If you remove the one for the rear door, it has a part number on it. I believe the front and rear door access panels are interchangeable ( so they use the same part numbers
Would this be the same process for the 2012 malibu
I don’t think so. I believe those don’t have this weird clips.
I replaced my back doors now they won't open is there something that I can do
Check the child-safety lock isn't on
WHY chevy make there tin like doors so complicated to take off.... Ford is easier to deal with.. Christmas 🎄 that mess up when you pop the door off and just replace them....LOL
Yup
I cant seem to get the screw out in the switch
It's loose but won't pull out?