Це відео не доступне.
Перепрошуємо.
watch out !! using a angle grinder||how to mount a cutting disc onto an angle grinder correctly
Вставка
- Опубліковано 4 лис 2022
- using an angle grinder must be very careful and vigillant, as it can be very Dangerous. here is||how to mount a cutting disc onto an angle grinder correctly||how to install a Cutting disc in an angle grinder||instally the cutting disc and using the angle grinder
Although it is a good practice to keep the disc face with the printed label downward and tighten the nut on the plain side, but it is not advisable to tighten by gripping the disc. Reason for keeping the label side down is to avoid the emery surface damaging the bottom plate. Always use the supplied wrench and by holding down the lock on the back side. Similarly always use the wrench to unscrew and always remember to remove the cutting disc after use. Otherwise there is every possibility of the disc getting damaged.
As mentioned by some others never use the machine without the guard and safety goggles.
Thanks.
Thanks sir🙏
I throw away the wrench tool and just hand tighten the disc, never had a problem, it is obvious you don't use a angle grinder every day!!
For disc cutting , just hand tightened slightly. The rotation will create the force that tightened the nut. But dangerous if twist / change direction when cutting.
But if sanding mode ,no harm done if hand tightened.Those but will tightened itself too
Very dangerous using wood saw blade on non trigger switch
What a load of bollox!!
Hahaha!
After seeing so many replies on the subject I remember this small write up;
He Knows not and he Knows that he Knows not!
You can Teach him.
He Knows but he Knows not that he Knows;
You need to awaken him.
He KNOWS and he Knows that he Knows!!
He is the Wise one and you can follow him.
However now comes the Dangerous one???
He KNOWS NOT AND HE KNOWS NOT THAT HE KNOWS NOT,'Oh! What a pity.' Always avoid him.
(I am from India and we have a saying, when translated it means,'It is enough to give just a Clue to the Intelligent person'.)
Thanks.
Always a good idea to check that the machine is disconnected from the power source (unplugged or remove battery) before installing or removing blades. And use the safety guard!!
Ok, thank you
I had a lot of old pipes and rebar to cut up and from what I read ua-cam.com/users/postUgkxPDBfLu68o58Aw85O_J-zIFfjJARBhp-3 this would be the tool for the job. Since I had never used one, I watched a couple of youtube videos and I'm so glad I did. Some really good safety tips, which I followed, and this tool did a splendid job. One good thing to know is the weight of the tool puts just about the right amount of pressure on the metal I was cutting, so I didn't have to use a lot of pressure, which is more likely to jam the tool. It made fast work of my job.
cutting disc position is not important,don't use grinder without disc guard. Best practice don't remove disc guard anytime,you can adjust disc guard by lossing screw and turning your hand.
Yes..thank you very much sir🙏🙏
Absolutely correct 👍
But disk gurd prevents the use of Standing wheel what to do for that ?
For me remove it or not the disc guard i dont care because im immortal
@@trickswelder3839 but you hold the machine wrong way, you have to hold the machine, like these dust going to front side ... but your holding system to dust throwing to your side.
One of the most important issues of using an angle grinder is the disc itself. Do NOT buy cheap discs! The cheap disc will break very quickly and at 10,000+rpm any small object flying out is deadly and without the safety guard the risk increase by x10.
😢
no no this is wrong 🚫
must need to use safety guard for angle grinder
Thank you🙏
No guard no gloves no face shield wow you the boss 😅😅😅
Unsafe because you forget to put or to install the grinding desc guard
Thankyou
I bought a new grinder and it's my first time.. so thank you for the tips.
Thank You
this video help me to demonstrate during my welding class. thanks alot.
Why don´t uses the security guard and the handle bar? Security first
Oh my bro... Disc guard is very important. Safety is number one.
Ok.. Thank you🙏🙏
We had an accident while using the grinder. The disc broke and the pieces flew everywhere, sadly my dad was hit on the shoulder. He had 8 stitches. Safety first, put the guard on and wear protective gears. I know it's hard to grind if there's a guard attached but safety is the priority. You'll eventually get used to it.
Ok.. Thank you very much sir🙏
The thin wire (Fibre thing) inside of it is scary as fck. Safety first
I used portable grinder big and small,sence 1978 until now ,but l make my own cover design if using the cutting disc, the original cover if l used grinding disc. I never meet accident if the disc is broken...Safety First Always...
Today only I purchased one ancle grinder. Your demo will be very useful to me. Many things (every thing) come to know me. Thank you very much sir..
Do not follow the video unless you want life injuries
Para que sirve el protector del disco y el mango para sujetar que trae la amoladora, por algo lo puso el fabricante.
Thank you sir🙏🙏
Never uses that dangerous tool with a single hand. Bad video
модель очков мне понравилась )
стиль 1970 ых сейчас в моде
بسیار متشکرم از آموزش خوب شما و نکات مهم که در این ویدئو آموزشی ارائه دادید......موفق باشید
🙏
Very dangerous to use without blade guard.
If blade brakes the flying parts can inflict fatel wounds
ਬਹੁਤ ਵੱਡੀ ਜਾਣਕਾਰੀ ਮਿਲੀ ਹੈ।
22 price kiya disc da dasi yaar❤
Very good👍
Mainly one wrong from you, must be use blade guard when cutter using.
Correct! Blade guard must be installed as protection incase the blade shattered...many don’t understand that safety...
Unsafe practice of using angle grinder....
Guard & handle are missing. Consider readinģ the disc label as it indicates the expiry date of the disc & its rate (rpm). The disc rpm should be higher than the machine rpm.
Ok.. Thank you very much sir🙏
Always use safety eye glasses while grinding. 👍
It is unsafe to use the grinder without a disk guard. Always tight the disk with the provided key/ tool, not your hand.
Cutting disk and the like have the arrow ➡ to indicate totation direction, always observe and follow that.
Thank you, sir
Great content !
I have often seen welders not using disc guard. It is dangerous without disc guard. My disc broke 2 times during use. Luckily i was using disc guard and broken pieces of disc didn't come towards me.
Ok. Thank you
thank you
Hahaha!
The most important thing you missed out. That is the safety guard.
Also one must not tighten the disc with hand as shown in the video. One must use the special tool suppled by the manufacturer.
And again along with the safety Goggles one must also wear proper clothing, preferably of Cotton or Denim.
Gloves is to be of Leather preferably and not Cotton.
Keep the surroundings cleared of Flammable liquids, waste Cloths etc. The sparks coming out the Grinder will easily ignite them and the person using the grinder will not even know it.
Thanks.
Ok.. Ok.. Thank you
Ok.. Ok.. Thank you
great tips.
This is totally against the law of using.disc should turn over to prevent split,spinning should spin against the tightening screw to prevent losen.this you are right.disc guard is vital.
🙏
This is called how to loose eyes or faces cutting No Guards... very nice cozzyy
You're soooo smart! You are my hero!!!!
Silently useful. Thanks.
good, thanks for share
Thank you very much🙏
A Mechanics Adventure
Very. Good
Thank you
Friend, put on the protective cover of your angle grinder！
Yes sir... Thank you very much🙏🙏
Thank You.
Thankyou very much🙏🙏
Where is the grinder guard?? and your gloves????...good to see you have utilize your eye protection.
.....And even handle to minimise shok in case the grinder kick back.
🙏
I'm ok on how you install the disc but on matters of safety it's very dangerous not to use the guard✌️
Please wear safety hand gloves and don't forget to wear glasses too. Thank you.
Ok.. Thank you very much🙏👍
And dont forget a dust mask....the dust generated can and does affect your lungs......I know first hand
You must use the key to tighten the disc and the disc guard must be in place before operating/using the grinder.
Thank you sir
UA-cam seems to be full of these self-proclaimed "experts". You're correct about the orientation of the disc but why are you doing everything without a guard? FAIL!
Ok. Thank you
wrong the washer allows the mounting nut the ability to remove abrasive disc if the blade gets jammed
Thank you sir
I think it is wrong placing of disc it should be inverted to loosen easily
Why manufacturers don't make clear / see thru guards??
very good information
Thank you sir🙏
It seems you forgot to install the most important safety feature .... the disc guard !
Thank you sir, for reminding 🙏🙏
Welcome to third world countries... who's needing disc grinding guards... they think take tooo much time take it on/off. Ohhhhhh wait one minute saved your life eyes and face disc spinning 3200---6500 RPM...ahhhhh
Good thank you
🙏
Thanku Sir ❤️
Jamais usar sem a proteção da máquina.
Ok. Thank you very much🙏
Legends not use disc Guard❗️😂😂😂
They are ready to stich body part❗️😃
Thank You
Helpful ❤
Cutting disk position is important and that sticker is danger that not properly stick it damage ur hand . First u must cheque power on button then plug and on.guard must for safety
Ok.. Thank you very much sir
வாழ்க வளமுடன்.nice working video
Thank you
No disc guard ! That’s the correct way to use the grinder for sure !
🙏
Sds-Clic is handy, doesn’t need additional tools to mount the disc.
Good job
Why no disc guard?
the rotation arrow of the disc has its purpose.
👍
Cutting disc. Quality and date of expire. Watching. Or. Grinding mission. Amber. Disc amber. Calculated. Safety guard very important. Dead man switch. Cutting wheel removing key. Any time inspection after you're. Full. P P E. Chaking..... After Start you're working...
Good your channel
Thank you very much🙏
Thank you Sir 👍👍
Correct way is not removing the guard
Thank You
Unsafe bec. You forgot to install Safety cover and hand gloves , maybe u dont also use eye protector
🙏thank you
Throw away disc guard
You are very wrong from the very beginning my friend! Guess what's missing? 😂😂😂
Sir angel grinder clock ways round leta hai ke anti clock ways
Re-do the video with safety guard and wrench for tightening the disc/wheel.
Thank You
Good
without angle grinder' s safety disc
guard ?
Use saftey guard first and use handle in stead of on body.
Thank you, sir
Thanks bro
Nice to the point information
🙏
TU EQUIPO DE PROTECCION PERSONAL Y TU GUARDA EN EL EQUIPO
Thank you sir🙏
Si tú intención es enseñar a colocar correctamente el disco, al menos colócale la respectiva protección al esmeril y usa la respectiva llave para ajustar con la pieza el disco.
Ok, thank you
What about the disk guard? If you going to make saftey videos you need to be safe.
Common boy, You did not yet experienced a broken cutting disc that smashed your part of your body that's why don't install the guard while you work or use.
🙏
Nice 👍
Its okay to use back to back the cutting disc some angle grinder have rubber thier wheel placement
Thank you
Thank you for this video I been doing the other way you showed not to for years had disk grab and catch explode cutting and turning with disk facing you makes sense pulls itself threw great video
Thank you
Tick sign is square root😂😂
cutting & grinding weel washer upon side very safety
Valami még hiányzik. A szikra vezető burkolat, ami megvéd ha véletlenül leszalad a gép az anyagról. Ha megmutatsz valamit akkor azt helyesen tedd meg.
Thank you sir.. I have fixed it in the next video🙏
Guard lagana bhulgaye kya . No safety
Good👍
Thankyou🙏🙏🙏
Bro Machine safety Gard use..
Thank you
Same more video pls
Even the elementery school boys,understanding this way...lol..
🙏
thank
Segurança em primeiro lugar.
Ok... Thank you sir
Think Safety Work Safely ✅
Ok.. Thank you sir🙏
Thank you
🙏🙏👍
Bạn chỉ quá tốt.
Cảm ơn bạn.
👍👍👍
🙏👍
Pourquoi vous avez enlevé le cache de sécurité
🙏 I have fixed it in the next video
Where is your disc guard
Wihtout gard hataka
Wery clever instrukcji👍👍👍👍👍👍👍👍👍👍🙂
🙏
Perigoso as proteção das máquina fundamental não se deve tirar foi projetada p segurança total
Wear is the safety gard?
Thank God And Amen ✝️
Thank you🙏🙏