I love your videos and must use "closed captions" for English. I am learning from your experience. I have three XK k100, three XK k110s, two XK k110 and two K130! My question: I used a k100 FC to power my semi-custom k110s. The performance is ok, but the tune is off somewhat? Roll seems good, but pitch forward and reverse is bouncing on the stops. The feather shaft is new and perfect. The blades, rotor head and blade grips stock. I can only figure the k100 board is tuned for brushed power. Any advice?
@@ericcoker8784 I think the K100 board is set for stability, but it's not too far off from the K110. The trick to tuning is to keep the rotor speed below 7000 RPM at zero pitch and see how it goes. If that doesn't work, try swapping the rod into the inner hole of the servo horn and testing it. The length of the servo horn can be used to adjust the mechanical gyro gain
@@RC_Heli_chanthank you for your help! Currently I have idle up#1 at 0, 60, 60, 60, 60. Idle up#2 is 70, 70, 70, 70, 70....as you can tell I use no "V" curve. I have no way to measure RPM yet. Also the mechanical adjustment is awesome, never knew that. I will definitely try that tomorrow!
こんばんは
いつもながら工作・修理が丁寧で素晴らしい。
真似できません(^◇^;)
動画編集も凄い。
最近K100飛ばしてます。
純正リポが弱って来たのでGNB
1s 300mAh 80C
1s 350mAh 70C
で飛ばし始めました。
300mAhの方が
パワーありますね。
Blade mCPXのオモリ付ローターにしたりと色々しながら飛ばしてます。
マイクロヘリは気楽に飛ばせるので楽しいですね。
こんばんは！
タマゾー君、K100でオートロに挑戦してみてください！
K120かK130のメインローターが必要ですが楽しいですよ！！
私も、オートロができるからK100を持ってるようなものです。
みんなでK100のオートロ動画大会しましょう。
いいですね(*^^*)
M2ExpEVO化した機体でもなんとかオートロ出来たので
やってみます。
K120/K130ローターが
必要なんですね。
K100メンテ後飛ぶようになってからやってみますね。
I love your videos and must use "closed captions" for English. I am learning from your experience. I have three XK k100, three XK k110s, two XK k110 and two K130!
My question: I used a k100 FC to power my semi-custom k110s. The performance is ok, but the tune is off somewhat? Roll seems good, but pitch forward and reverse is bouncing on the stops. The feather shaft is new and perfect. The blades, rotor head and blade grips stock. I can only figure the k100 board is tuned for brushed power. Any advice?
@@ericcoker8784 I think the K100 board is set for stability, but it's not too far off from the K110.
The trick to tuning is to keep the rotor speed below 7000 RPM at zero pitch and see how it goes.
If that doesn't work, try swapping the rod into the inner hole of the servo horn and testing it.
The length of the servo horn can be used to adjust the mechanical gyro gain
@@RC_Heli_chanthank you for your help! Currently I have idle up#1 at 0, 60, 60, 60, 60. Idle up#2 is 70, 70, 70, 70, 70....as you can tell I use no "V" curve. I have no way to measure RPM yet.
Also the mechanical adjustment is awesome, never knew that. I will definitely try that tomorrow!