I just started researching thermistors yesterday. How crazy is it that you post this today. I have an offgrid refrigerator that has a fairly large temperature difference between the top part of the fridge and the bottom part. I want to use a thermistor at the bottom and top of the fridge in a circuit that will turn on an internal circulating fan when there is a temperature differential between the 2 sensors. Great explanation video. thx.
As an automotive tech, an ASE Master since 78, many ask me about "Low Fuel Sensors." While changing a defective fuel pump, a number of models had the "LED" low fuel light. While not testing or saving these from the trash, I would guess they use a simple "NTC" thermistor. They are a single wire going to the dash in cars & and newer motorcycles, the can has small holes allowing fuel to enter, but always placed on rigid mounts, a few inches from the bottom of the tank. This leaves you with 3+ gallons I have noticed, to keep to running until the next gas station (Unless in South Dakota). With one wire soldered to the fixture, the other exists the tank to the dash light. Inside the 3/4" can, I have found stainless steel wool pack around the thermistor while the other had aluminum foil wrapped around it loosely, but always the wrapped with a parchment paper for insulation wGas is a liquid obviously, but when low, the thermistor is uncovered allowing a few amps via resistor to let it get warmer. As the thermistor gets warmer, resistance drops and the low fuel LED comes. Many happen fast like a 3/4 circle on/off ramp on interstate. With 25 to 30 mA required to turn on an LED, this seems perfect for the job. Most schematics show the return wire simply going to the dash light while others show "Block Logic" circuitry in the dash. Now retired, I would need to order a few to test in a 12.6-14.8 Vdc circuit. Do you have any thoughts? Thanks! Job well done! (No offense: but when teaching during a class of 12, or a seminar up to 100+ techs, owners and instructors who worked at the tech school in 7 states; I would ask them t4, the hotter you get them, the lower their resistance) no offense Megan! Retire ASE Master Tech
The Karen we all need in 2021! Thanks for the info! Exactly what I needed, and all done without a bunch of extra fluff. You get internet kudos from me ;)
2:05 that graph is not talking about the resistance value changing in a linear fashion or degrading. It is telling you that you can operate the resistor at is rated power up until 70° C ambient temperature. Then you need to reduce the power or you will damage the device.
Thermocouples in lower-cost applications are usually paired with an amplifier like MAX31855 (~$5), which gives a digital reading of an absolute temperature over SPI (or I2C for other chips) and provide typically much better than 2 degree accuracy with no calibration needed over a huge temperature range...
I have an window A/C unit that I need to get the room to 60 degrees but the unit will only allow me to set it to 64. I am trying to control the temp by using and Inkbird temperature controller that turns the A/C unit off and on via the outlet based on the inkbird's sensor. In and effort to get this to work, I have tried relocation the A/C unit's thermistor and insolate it but the results are inconsistent. Can you tell me if I can provide a set temperature reading on the sensor circuit be removing the thermistor and replacing it with a 9K ohm resistor so that it reads a constant 30C?
Karen I have watched your logic vids. The questions I have is if you have very specific and expensive part and obsolete how can one model the part with less expensive parts .the part I need to model has counters, latchs and a multiplexer,
So... Noone uses Kelvin (very application specific, I know) and just about only USA uses non-metric values. Why go all bonkers in the calculations to be able to plot values in C? Why not use those values as a default?
Assalomu aleykum
Siz chiqargan videolarizdi mazza qilib ko'raman kayfiyatimxam ko'tariladiii raxmat judayam yoqimtoysiz 😊
ishlarizga omat❤🎉
You deserve more than a million hearts and not only one!
Thanks a lot for your professional and detailed lecture,
Please keep posting more videos ....
I just started researching thermistors yesterday. How crazy is it that you post this today. I have an offgrid refrigerator that has a fairly large temperature difference between the top part of the fridge and the bottom part. I want to use a thermistor at the bottom and top of the fridge in a circuit that will turn on an internal circulating fan when there is a temperature differential between the 2 sensors. Great explanation video. thx.
As an automotive tech, an ASE Master since 78, many ask me about "Low Fuel Sensors." While changing a defective fuel pump, a number of models had the "LED" low fuel light. While not testing or saving these from the trash, I would guess they use a simple "NTC" thermistor. They are a single wire going to the dash in cars & and newer motorcycles, the can has small holes allowing fuel to enter, but always placed on rigid mounts, a few inches from the bottom of the tank. This leaves you with 3+ gallons I have noticed, to keep to running until the next gas station (Unless in South Dakota). With one wire soldered to the fixture, the other exists the tank to the dash light. Inside the 3/4" can, I have found stainless steel wool pack around the thermistor while the other had aluminum foil wrapped around it loosely, but always the wrapped with a parchment paper for insulation wGas is a liquid obviously, but when low, the thermistor is uncovered allowing a few amps via resistor to let it get warmer. As the thermistor gets warmer, resistance drops and the low fuel LED comes. Many happen fast like a 3/4 circle on/off ramp on interstate. With 25 to 30 mA required to turn on an LED, this seems perfect for the job. Most schematics show the return wire simply going to the dash light while others show "Block Logic" circuitry in the dash. Now retired, I would need to order a few to test in a 12.6-14.8 Vdc circuit. Do you have any thoughts? Thanks!
Job well done!
(No offense: but when teaching during a class of 12, or a seminar up to 100+ techs, owners and instructors who worked at the tech school in 7 states; I would ask them t4, the hotter you get them, the lower their resistance) no offense Megan!
Retire ASE Master Tech
It's been a while since I've checked in. No surprise, Karen's TLC videos are still absolute bangers.
Needed some information on thermistors for a research paper, and I stumbled across this video. I found everything I need! Thank you
which thermistor is better 10K or 5 K
The Karen we all need in 2021! Thanks for the info! Exactly what I needed, and all done without a bunch of extra fluff. You get internet kudos from me ;)
Very very comprehensive !! Thanks !!
2:05 that graph is not talking about the resistance value changing in a linear fashion or degrading. It is telling you that you can operate the resistor at is rated power up until 70° C ambient temperature. Then you need to reduce the power or you will damage the device.
Yep picked up on that as well. It is a curve showing power derating above 70deg C only because of cooling of part.
Thermocouples in lower-cost applications are usually paired with an amplifier like MAX31855 (~$5), which gives a digital reading of an absolute temperature over SPI (or I2C for other chips) and provide typically much better than 2 degree accuracy with no calibration needed over a huge temperature range...
Wrong description of thermocouples at time: 6:33.
I think they are usually MORE accurate than NTC for temperature measurement.
Don't wanna learn anything , i'm just here for Karen !
Hahaha, yeah... She's pretty cool.
Great Learning!
It's really hard to find good tutorials or learning's in my native language.
So now I'm gonna stalk your channel :)
thanx for this video , but what is doped mean ?
nicely explained , thanks
Hi Karen best explanation of circuit
This is helpful. Thank you.
So does it matter what resistance value I use then?
Nice explanation with this he sense of humour 👍
I have an window A/C unit that I need to get the room to 60 degrees but the unit will only allow me to set it to 64. I am trying to control the temp by using and Inkbird temperature controller that turns the A/C unit off and on via the outlet based on the inkbird's sensor. In and effort to get this to work, I have tried relocation the A/C unit's thermistor and insolate it but the results are inconsistent.
Can you tell me if I can provide a set temperature reading on the sensor circuit be removing the thermistor and replacing it with a 9K ohm resistor so that it reads a constant 30C?
Thank you!
hi, i am so glad that you are karen about thermistors and that's no joke 😂Oooo-my... a wonderful walk thru video, thanks 🥰🥠☕🐥
Karen I have watched your logic vids. The questions I have is if you have very specific and expensive part and obsolete how can one model the part with less expensive parts .the part I need to model has counters, latchs and a multiplexer,
which thermistor is better 10K or 5K or 2.25K ??
Fantastic!
Thank You!!
Interesting... Thanks, Karen!
how do you tell if its n or p type
Very nice
Cool !!!
Thank you. I have to tell an engineer with a masters degree how this works
Best love you
So... Noone uses Kelvin (very application specific, I know) and just about only USA uses non-metric values.
Why go all bonkers in the calculations to be able to plot values in C? Why not use those values as a default?
✌️✌️
🙏🙏🌹🌹
I sell small ntc 10k for students' experiments. I follow more Karen videos than those of men. Women voice calls men.
Hot