RC Aerodyne Roban Bell 412 maiden flight
Вставка
- Опубліковано 23 сер 2024
- ok...specs,
Roban 800 size Bell 412 from RC Aerodyne
weight: +- 22 lbs ready to fly
700 mm main blades
150mm tail blades
X2- 6S 5000 mah 20C packs for 12S
flight times: 6-6:30
Scorpion 4035-530 KV motor
Castle Creations Edge HV 160 with fan...(Overkill!!!)
Naza 3-Axis gyro system
Hitec radio system with 9 ch Optima receiver
OMG servos from RCAerodyne
ScaleRCHelis High Power 11ch light controller
![Lp. Сердце Вселенной #1 НАЧАЛО ПУТЕШЕСТВИЯ [Новый сезон] • Майнкрафт](http://i.ytimg.com/vi/380Q7gLWGvk/mqdefault.jpg)
that was one of the best informative maiden flights i have seen. You really talked us through your thoughts and showed why you felt the adjustments need to be done. GREAT job, THANK YOU!
Glad to see you got it sorted out! Great looking heli!
Браво!
Looks great ! I'm about to purchase my first scale. How does this brand hold up overall ? Also is the angled tail models less reliable ? Thanks
Sounds good Mike!! Thanks for the response!! RCHN 5 ??
Nice Heli - My naza tail is very similar did you calm it down by adjusting the tail throw end points in naza? Its Ok in atti and gps but too sensitive in manual?
OK Thanks, will lower my TX to see if it calms things down for me
Great informative vid! What is the max pitch on this bad boy...also will a mini vbar work in a model like this? Thanks.
@@JestRR Thanks again for the quick reply!
I've been thinking about getting the bell 429 pretty seriously here recently... How was the set up of the castle ESC and BEC as well as the Naza H? I can't find any videos on one of these superscale builds from beginning to end just a little nervous not using castle products before or Nazza for that matter...
Thanks for the speedy reply… All the things I see about castle on UA-cam are usually for like eight scale buggy's or something like that can you refer me to a UA-cam video for helicopter set up ?
Was this an RC aerodyne build…? If so did it go smoothly I hear a lot of things about the blades being very unbalanced… I'm not a super experience builder I've been using the 600 platform and putting them into the scale fuselages with pretty good success over the years… As I said earlier I'm just a little leery as I've never set up a very large helllike the super scales
Thanks for the info I saw your build in 2013 of your bell 429... Looks like you got a bare-bones kit does RCA still send them out like that…? I looked on RCA's website for their bill for 29 and look at the instruction manual it looks like most of the interior stuff doors etc. already finished is that the case? As I stated earlier i've only put 600 mechanics such as the racks etc. into RCA scale fuselages i've never built a superscale 700 before…
Thanks man I really appreciate your input helps me to feel more comfortable with diving into this big project… Looks like you guys are pretty big builders from all the videos I saw on UA-cam of you and your friends where you guys located I'm down here in Brooksville Florida which is just north of Tampa
Add love to chat it up with you you have a Facebook account?
will 120a esc do fine?
@@JestRR thanks, i opted for 130, hobbywing's 120 can handle up to 6s only
What's your throttle position at 6 degrees of main rotor pitch? Thank you.
THank you.. are you in idle up when you were hovering?
Thank you for the information Jest. I really appreciate your reply to my inquiry.. :-) I have the 800 bell 222 from Aerodyne and still fine tuning it.. been just hovering it.. haven't did any real flying around..
I'm from Kodiak, Alaska and there's not much a lot of hobbyist around my area.. :-) I wish I'm in a place close to the professionals and would have been nice.. Will be a while 'til it will be flying around.. haha
wow! I just watched the link you gave me. the ec-145 crash. that was really bad. I think the bolt that secures the head into the shaft isn't tight and been nicked until finally gave.
fahmi.