Homemade Tool

Поділитися
Вставка

КОМЕНТАРІ • 21

  • @allanb52
    @allanb52 Рік тому +4

    I assume this is ordinary mild steel (low carbon). 1. you could bend that without the cutting/welding. 2. The heat treatment will do nothing with that carbon content.

    • @djpaulk
      @djpaulk 11 місяців тому

      I was going to tell him that, but he is a relentless stupid video poster.

    • @outkast937
      @outkast937 5 місяців тому

      The way he attempted to heat treat it wont work anyway... A single heat and quench with just water? Dude achieved nothing.... Needs a few more cycles being quenched in old motor oil and then about 8 hours in an oven.. then he might actually achieve something, but considering dude went through all that effort just to make the worlds crappiest hammer...

    • @allanb52
      @allanb52 5 місяців тому

      @@outkast937 Like I said before, you cannot heat treat low carbon steel. If the carbon content were higher you do harden the steel by heat to red and a single quench. Then you gain toughness by tempering it, which is done by heating to a certain colour and quenching in oil. "Old engine oil" you sound like a mechanic, but it would work...Yeh, you can buy a proper hammer for a few quid.

  • @user-jy9nc7bq4m
    @user-jy9nc7bq4m 5 місяців тому +1

    Скоро из полипропиленовой трубы гвоздодер сбацает, а там и до пластилина рукой подать.

  • @kannigasiva5621
    @kannigasiva5621 11 місяців тому

    Very Nice

  • @user-kg7zorge
    @user-kg7zorge 11 місяців тому +1

    Термоусадку нужно одевать с клеевым составом в нутри!!! Тогда точно не сползёт с ручки!!!

    • @kargon3533
      @kargon3533 5 місяців тому

      Деревня, там уже есть житкая резина, она и клеет. Ты не то видел.

    • @user-kg7zorge
      @user-kg7zorge 5 місяців тому

      Мужик с хутора, ты не видил райхемовскую термоусадку!)))

  • @Russell-me7sf
    @Russell-me7sf 4 місяці тому

    Don’t get me wrong, it’s great that people take the time to make tools, But have you people not heard of B&Q and claw hammers 😂

  • @user-up5vx5dv7h
    @user-up5vx5dv7h 5 місяців тому

    Вот точно такая же фомка, только кованая и работает -в магазе 500 р стоит
    А ты из чего и чем делаешь?
    Для вида?

    • @Coravel91
      @Coravel91 4 місяці тому

      Когда коту нечего делать он яйца лижет.

  • @user-wt3sh4hl9u
    @user-wt3sh4hl9u 5 місяців тому

    Сталь три не закаливаеться.😂

  • @AlexA-bl5vd
    @AlexA-bl5vd Рік тому

    Красавчик!!

  • @user-cm1od3dz3m
    @user-cm1od3dz3m 11 місяців тому +1

    Да когда же все эти бездельники купят себе в маркетах по нормальному гвоздодеру?!

  • @user-qx5xe4kp7j
    @user-qx5xe4kp7j 5 місяців тому

    Доктора-а-а!!!

  • @user-ku4xz1ps2m
    @user-ku4xz1ps2m 3 місяці тому

    Пускай самый маленький гвоздь из ясени или акации достанет своим гвоздодёром

  • @TheMRSTEVEN
    @TheMRSTEVEN 5 місяців тому

    I had high Hope's for this one, but as always shit.