Thank you God! I finally found an option that is well engineered to do my 96 SS. Awesome video. Thanks for posting. If you're in MN, I'm dropping my car off to you. Would love to do the LS swap too. I have a cammed 5.3 in my white 93 Caprice, but have yet to buy a transmission crossmemeber and still need an efi intake wiring harness and ECU. I was trying to do it on a budget, but all the things I mentioned are not cheap! Going to be checking out more videos on your channel to see if you can help me on that too.
Hey man been watching your videos...and i just bought a 96 caprice classic and tha guy that had it before me tore out the whole lower dash down to tha wires..i was trying to see if u could make a video on how to put one back together or point me in tha right direction...thanks alot
I know you said you use SEM medium gray for the grey part, what did you use to paint the Etchus face plate? Any prep to stick? Thanks man, you’re the guy that put me onto this. I’m clamped and ready for epoxy. Car is ready but two dash tabs missing and a salvage heater control with only one tab. The rest is ready, but setbacks suck.
@@otgmechanic I just ordered a can of landau black and a can of medium grey. $40 bucks! Big bucks! Thanks again man! If it weren’t for you I’d be in the 90’s with that stock deck forever.
I will say, when I used my air saw to cut the stock faceplate off, I was as nervous as a whore in church! Used a bastard file to finish the edges. For some reason I thought the faceplate went in from the back. All that detail work only to puss it up with epoxy. I really appreciate you man. Thanks for being so helpful.
I think the reason the unit is tilted is you didnt put in the 1/4" spacer on the top hole behind the aluminum bracket. The spacer is a nut, as in a nut for a bolt. Confused me at first, because I was looking for a rectangular piece with a hole, but after watching the factory install video, it was confirmed. Some day I'd like a dashboard like K.I.T.T. from Knight Rider. Ha Ha!
Looks like a replacement HVAC switch panel, maybe that's why the dash looked like it was off before. Any thoughts on the detailSS kit vs the etchus? Looking into it for my 9c1
What’s the biggest unit width wise that will fit? I measured from out side and I’m thinking roughly no more than 7inch unit would fit flush with trim kit and all correct?
Man bro no lie u kno those clips that holds tha dash n theres a holes that it holds it in try to Sharp it a lil so tga clips can snap on real easy cause i hated when u try to pull it out n then it breaks one of tha clip so try that n tell me does it comes off easier no lie bro it works that way real talk n then if u want to keep that bottom dash careful then put jb weld bondin for plastic on tha back of to use a small brush n it has to be in white n black to mix it up so u have to do it fast to brush all over it n not to put to much so when u get it right n let dry for two days trust me bro it really really works to keep that bottom dash hard n wont break at all
@@otgmechanic 🙏 thank you! You got down on this project. I’m trying to restore my window switch bezels. Do you know where I might get the lettering for them?
Just got my kit today can’t wait to install it tanks for the videos 💯🤝🏽
Here from Cool Cars KJ page. Love the Impala! Subscribed
Welcome! I’ll keep the impala content coming!
Beautiful job!!!! Very nice work!
Just some advice when I did mine I was scared to mess up the cutting so I use a utility knife and scratched back and forth to we’re it was easy to cut
Definitely looks factory bro. Nice vid!!!
Thank you God! I finally found an option that is well engineered to do my 96 SS. Awesome video. Thanks for posting. If you're in MN, I'm dropping my car off to you. Would love to do the LS swap too. I have a cammed 5.3 in my white 93 Caprice, but have yet to buy a transmission crossmemeber and still need an efi intake wiring harness and ECU. I was trying to do it on a budget, but all the things I mentioned are not cheap! Going to be checking out more videos on your channel to see if you can help me on that too.
Love the Content Bro !
Thank you sir!
Hey man been watching your videos...and i just bought a 96 caprice classic and tha guy that had it before me tore out the whole lower dash down to tha wires..i was trying to see if u could make a video on how to put one back together or point me in tha right direction...thanks alot
U dope as hell bro 😎 on them ss impala no doubt 💪🏽
Love the content bro my B4U is fun and will be alright if you just keep the videos coming
Nice work
I know you said you use SEM medium gray for the grey part, what did you use to paint the Etchus face plate? Any prep to stick? Thanks man, you’re the guy that put me onto this. I’m clamped and ready for epoxy. Car is ready but two dash tabs missing and a salvage heater control with only one tab. The rest is ready, but setbacks suck.
Landau black for the faceplate
@@otgmechanic Thanks man! Going to go grab some! Looking for a 5 ounce syringe with a plastic tip to run my epoxy.
I’m hoping Walmart has some.
@@otgmechanic I just ordered a can of landau black and a can of medium grey. $40 bucks! Big bucks! Thanks again man! If it weren’t for you I’d be in the 90’s with that stock deck forever.
I will say, when I used my air saw to cut the stock faceplate off, I was as nervous as a whore in church! Used a bastard file to finish the edges. For some reason I thought the faceplate went in from the back. All that detail work only to puss it up with epoxy. I really appreciate you man. Thanks for being so helpful.
@@otgmechanic what kit did you use to move the ac control to the bottom
That double din is so shallow could it fit @ the bottom where the original radio was
I think the reason the unit is tilted is you didnt put in the 1/4" spacer on the top hole behind the aluminum bracket. The spacer is a nut, as in a nut for a bolt. Confused me at first, because I was looking for a rectangular piece with a hole, but after watching the factory install video, it was confirmed. Some day I'd like a dashboard like K.I.T.T. from Knight Rider. Ha Ha!
Ohhh that's what the random nut is for😂😂
Cutting a perfect dash is scary still. 🤣🤣
Great work though.
Looks like a replacement HVAC switch panel, maybe that's why the dash looked like it was off before. Any thoughts on the detailSS kit vs the etchus? Looking into it for my 9c1
I have a few videos comparing the 2.
Oh snap. VA car. 💪🏾💪🏾💪🏾
Looks clean but idk about cutting the dash up lol
Good video
How much you charge for this service...and wats the turn around time??
One of my clips are broken for my lower dash so it’s not fitting completely on, you know anything I can do to fix that?
E6000 adhesive
@@otgmechanic thank you ✊🏽
@@otgmechanic Awesome! I got two bad clips. Etchus is good to give you kudos. I hope they hooked you up.
What’s the biggest unit width wise that will fit? I measured from out side and I’m thinking roughly no more than 7inch unit would fit flush with trim kit and all correct?
Correct
We need an after market bezel kit.... New plastic..... No company is remaking the underdash bezel
So you are working on being KING SS?? LOL... good video brotha..
Working on being better than I was the day before and doing quality work for my clients.
@@otgmechanic where are you located??
@@mikeammargon6847 right outside of Atlanta
Man bro no lie u kno those clips that holds tha dash n theres a holes that it holds it in try to Sharp it a lil so tga clips can snap on real easy cause i hated when u try to pull it out n then it breaks one of tha clip so try that n tell me does it comes off easier no lie bro it works that way real talk n then if u want to keep that bottom dash careful then put jb weld bondin for plastic on tha back of to use a small brush n it has to be in white n black to mix it up so u have to do it fast to brush all over it n not to put to much so when u get it right n let dry for two days trust me bro it really really works to keep that bottom dash hard n wont break at all
Brother I couldn’t catch the name of the paint you use for match.
Sem medium grey
@@otgmechanic 🙏 thank you! You got down on this project. I’m trying to restore my window switch bezels. Do you know where I might get the lettering for them?
So you are located in Dallas tx
Nope. Atl
i am looking for lower dashboard for 96 impala can you help
@impalassparts on ig would be your best option.
Where can you buy that installation kit from
Link in bio
Why cant the radio just be left at the bottom...seems like enough room
I wld like for you to up grade my engine wld it be possible, or can we communicate by phone , pls
Lol I sho kept saying pull the whole ash tray out lol
How much u charge to put a double Din in a 95 impala
Labor is $200
Where did you order your kit from
Bro do you repair those dashes and prepare them for the dd kit ?
Depends on how bad they are
When I get back to Ga I’ll send you a picture
@@shawn112680 hit me on Ig @otgmechanic
I just added you
I subscriber to u 721 Im about to get an 96 impala i always wanted one and im about to get one and i need all the help i can get
What size is that screen?
Pls!
Becareful being yanking on it……
Scary when you kept yanking on the dash. Would have been an upset customer.