Forget it, they have to sell PCB boards, if they give you the schematic you go to easyeda and do it yourself or you could buy it elsewhere. When I see this, I usually block the channel, otherwise only sites that sell PCBs will come out, which are often not professional at all, since well, their goal is to "sell", and the more mistakes the more you buy.... This is the "new economy babe".... Like farwest or anarchy
I Am using egs002 module and using data sheet diagram of egs002 module to built inverter but it again and again blink light 3 or 4 time showing under or over voltage
Good morning sir. Please I would like your help which will be precious to me. I made a sine wave inverter with EGS002 voltage 12 DC, 16 mosfet IRF3205 transformer that exceeds 20 amps. Here is my problem with no load the circuit consumes 1.8 amps as soon as I plug in a 75 W bulb the load current increases to 10 amps. Transistors don't heat up, output voltage is always stable etc... Please where is the fault? A 75w 8 amp bulb then imagine 4 or 5 bulbs or even more a TV?
It is very inneficient, an inverter of 50 hz or 60 hz; a 3000 watt transformer for that is a beast of 30 kgs, burns lots of Amps; all comercially sold inverters are high frequency ,25000 khz to 35000 khz, so the transformers, several in the same inverter are very small and they don't burn many Amps on themselves; that is the way to go; these kinds of videos made me sad,they fail to tell the whole story,and some people get burned; ALWAYS study all matters as deeply as you can, look up many videos and googlings, for hidden dangers, here some youtubers ,either don't know,or they try just to get more views at any cost,or both.
@@josepeixoto3384 Thank you very much for the answer sir. So the ideal is to convert the voltage 12V DC to 320v DC frequency about 20 kHZ then inject this voltage on the inverter. That is to say the primary of the inverter will be 320v Dc its output 240v AC. Good luck sir
I use optocoupler gate drivers Ic to protect the egs002 from burn out is the h bridge mosfets failed you should too
Very nice design very clearly all discrete components will you be willing to upload your Gerber file for the PCB thanks.
Galing mo po sir solid 💕💕💕
Thanks for watching sir
You did a very good work
The archive has not been uploaded to the board?
Hello! Can you give a link to the diagram for your board? Thank you in advance.
Forget it, they have to sell PCB boards, if they give you the schematic you go to easyeda and do it yourself or you could buy it elsewhere. When I see this, I usually block the channel, otherwise only sites that sell PCBs will come out, which are often not professional at all, since well, their goal is to "sell", and the more mistakes the more you buy.... This is the "new economy babe".... Like farwest or anarchy
I tried to buy the board because it is extremely compact and they didn't tell me how I could buy it. I need a compact inverter like this.
Can you upgrade my china made pure sinewave inverter from 500w continues load to 3000w continues load?
nice project....pls I don't know if I can get your gerber file for the project's pcb
maybe he forgot....... Yes, right
Is there any way to reduce no load current? It is about 1.8A
Try to using inductor in series before transformer, about 50uh inductor, dont forget make it high amp.
@@SatuJalur_indo Thanks,I have already added this inductor and the current is reduced from 3.5 to 1.8. Is there a way to reduce it?
Thanks,the link is not working,it will lead to coconut harvester circuit diagram and code and not the pure sine wave inverter
Okay, I will fix it soon
@@AAElectrotech when you're done fixing it let me know
I Am using egs002 module and using data sheet diagram of egs002 module to built inverter but it again and again blink light 3 or 4 time showing under or over voltage
There's a issue with Feed back circuit of your inverter circuit either it's not connected properly back to egs002
Take a look at the EGS002 signal table and also at the feedback stage.
link takes you to wireless coconut harvester not inverter
good day sir! If possible, email me the board file, I want to order on PCBWay
Good morning sir. Please I would like your help which will be precious to me. I made a sine wave inverter with EGS002 voltage 12 DC, 16 mosfet IRF3205 transformer that exceeds 20 amps. Here is my problem with no load the circuit consumes 1.8 amps as soon as I plug in a 75 W bulb the load current increases to 10 amps. Transistors don't heat up, output voltage is always stable etc... Please where is the fault? A 75w 8 amp bulb then imagine 4 or 5 bulbs or even more a TV?
It is very inneficient, an inverter of 50 hz or 60 hz; a 3000 watt transformer for that is a beast of 30 kgs, burns lots of Amps;
all comercially sold inverters are high frequency ,25000 khz to 35000 khz, so the transformers, several in the same inverter are very small and they don't burn many Amps on themselves; that is the way to go;
these kinds of videos made me sad,they fail to tell the whole story,and some people get burned;
ALWAYS study all matters as deeply as you can, look up many videos and googlings, for hidden dangers, here some youtubers ,either don't know,or they try just to get more views at any cost,or both.
@@josepeixoto3384 Thank you very much for the answer sir. So the ideal is to convert the voltage 12V DC to 320v DC frequency about 20 kHZ then inject this voltage on the inverter. That is to say the primary of the inverter will be 320v Dc its output 240v AC. Good luck sir
Admin kindly upload the schematic diagram
Mua pcp ở đâu vậy anh
Awessome!!!
Bro nice project but the link is wrong...
I'll check it
The link to download is wrong
noooo, realy? noooo....
nice video...
why not give us a workable link for the project files if you really what to share
how to buy you pure sine wave?
You can buy on shoope
but i want to buy yours
Yes you can buy mine.
I will share the link If it was available
@@AAElectrotech shopee or aliexpress
hi give me the gerber file please
😯
I need pcb board
Brother your project supper please give me circuit diagram gerber file
Okay wait for me, I will search the file in my Pc
Without a circuit diagram and where to buy the printed board your video is of no use. Cannot understand why you didn't think of it
Please gerber file/layout pcb sir🙏
Pay!!!! the time for sharing is over, now you have to pay to write posts too...... By the way, did you pay for this? hai, hai, hai..... no good....
these videos are not worth much, there is no place to order the PCB from,what a pity; i mean a ready PCB, ready to buy; or is this one ready for sale?
Hi
I'm really tired of all of you