Thank you, thank you, thank you...Your video was perfect for the issue that I had. I had filament that was broken off in the area between the filament chamber and the hot end. I gave the video a thumbs up and subscribed to the channel. I am off and printing for the weekend.
Thank you so much, I am only a few days into having this printer and its a bit different then the others I've used so far so this was extremely helpful.
Thanks, my problem, used some old PLA from amazon, just needed a single part in one colour. Lolz, within a few days it has broken itself into about 10 pieces, bits jammed everywhere! From now on, I keep with the original Bambu filament.
Thank you for this video! After printing the first items with the sample filament, it already got stuck because the filament ended😅 I had stuck filament in the nozzle and inside the AMS system 🫠 But solved it!
Thanks for sharing, my first brake and clog on my A1. Back online and printing, I went through about 4 spools before any issue, these printers are solid. Thanks again! New sub also...
My issue wasn't in any of the places mentioned. I was using a cheap variety of PLU which broke off around half an inch above the top of the nozzle within the print head body and caused a blockage. After breaking off the filament I used piece of stiff wire a little smaller than the diameter of the filament to push it through while turning the extruder knob until the wire poked out the bottom of the extruder. I then refitted the nozzle and other pieces and reloaded the filament. It worked for a single print before it happened again. The solution? Use good quality filament especially when using soft or foam filament.
Tip! If despite every tutorial you just can't figure out what gets the filament stuck, check the filament hub from below and try to see it. Pull with tweezers and it should help
Help please. I don't do 3D printing, but my kid does. His filament is broken at the other end of the tube. So it's not connected to the spool anymore. How do I fix this? Thanks.
➡ Nozzle Replacement - amzn.to/3ANXZSA
➡ Popular Filaments - amzn.to/3XoXY0P
➡ Top Rated Printers - amzn.to/3VuR6wn
➡ Resin Printers - amzn.to/3XuuC0R
I was so frustrated with my printer, this was so much faster! exact same process for the bambu a1 for those wondering!
Thank you for this video. I would have broken mine if I didn’t stop and watch this video.
You are my hero i tried so many things and this video saved me from more hours of misery 🙏
Thank you, thank you, thank you...Your video was perfect for the issue that I had. I had filament that was broken off in the area between the filament chamber and the hot end. I gave the video a thumbs up and subscribed to the channel. I am off and printing for the weekend.
🙏
Thank you!
Worked great! Thank you so much!
Thanks to you I was able to start printing again. Thank you, you are a god.
Very helpful. And contains the best explanation of how to pull out PTFE tubes from original splitter. Gread job!
Thank you so much, I am only a few days into having this printer and its a bit different then the others I've used so far so this was extremely helpful.
Thanks, my problem, used some old PLA from amazon, just needed a single part in one colour. Lolz, within a few days it has broken itself into about 10 pieces, bits jammed everywhere! From now on, I keep with the original Bambu filament.
Your video got my printer going again! Thanks.
Fixed my issue, you just got another subscriber.
Thank you for this video! After printing the first items with the sample filament, it already got stuck because the filament ended😅 I had stuck filament in the nozzle and inside the AMS system 🫠 But solved it!
Thanks for sharing, my first brake and clog on my A1. Back online and printing, I went through about 4 spools before any issue, these printers are solid. Thanks again! New sub also...
Man this really saved me so much trouble on the A1 thanks man!
Thanks, man. You're a lifesaver!
Very helpful video. Very well done! Thank you!
My issue wasn't in any of the places mentioned.
I was using a cheap variety of PLU which broke off around half an inch above the top of the nozzle within the print head body and caused a blockage.
After breaking off the filament I used piece of stiff wire a little smaller than the diameter of the filament to push it through while turning the extruder knob until the wire poked out the bottom of the extruder.
I then refitted the nozzle and other pieces and reloaded the filament.
It worked for a single print before it happened again.
The solution?
Use good quality filament especially when using soft or foam filament.
You just earned yourself a new subscriber
Really wish I would have looked this up before canceling my print. It would have saved it, at least I wasn't far into it. Thanks for the help.
Thank you! This was very helpful!
This helped me, thanks! I subscribed and liked the video. Keep it up.
Thanks!
No problem! Thank you! God bless
Thanks for the video! Helped me immensely! Now.... how to figure out how to (manually) change filament mid-print when the need arises. :)
Tip! If despite every tutorial you just can't figure out what gets the filament stuck, check the filament hub from below and try to see it. Pull with tweezers and it should help
Thank you! This helped me alot!
Thanks!!!
Worked for me, thanks!
Soy filamwnt didn't push through the extruder any ideas?
I have a blockage between the ams tub and the hotend. How do I access that?
shut it off even tho I'm always threw a print? will I be able to re start it no problem?
Thank you so much
Help please. I don't do 3D printing, but my kid does. His filament is broken at the other end of the tube. So it's not connected to the spool anymore. How do I fix this? Thanks.
“A tweezers”, “a pliers”
i have a bambu lab 0.2mm nozzle and i really dont want to need to buy nozzle after nozzle after nozzle on $15 an hour ;_;
what kind of filament do you use in it? Is it clogging often?
Thanks!
Thank you! It really helped.