Nice job! You sure like living on the edge. If I tried that, the pin would have fallen ALL the way out. Worked well for you. Thanks for showing us a different way to "skin a cat".
Slick way of doing that with the bolt. I've pulled stuff like that with just the wire... tack it... dispense wire once grounded out, clip, curl in a loop, and pull that. Whatever works!
Good job, but you forgot one thing, cutting the excess off those shackles! Ha just kiddin’. Great idea though. I don’t know if I would have thought of that!
If you reach under the dash and unhook the speedo cable you can pull the center out and spray motorcycle cable lube or chain lube down the housing till it comes out at the trans and put the cable back in and connect back to the speedo. LOL, ask me how I know this. I may have already asked, are you going to Bowling Green to Holley MOPARty this weekend? I'm going up Saturday.
Dang it Joe! All that knocking under the car is where the heat from welding that bolt to the pin took the temper out of a rod bearing! It says so in the UA-cam comments, so it must be true!
@@JustMoparJoe. They are used in a mag drive pump. When they are disposed of at work I split the magnet housing and pull the magnets. The best magnet I've used, I'll send one to ya.
@@johnwilburn lmao....you know what's worse than a 30 Min air cleaner install video?....a 45 Min Sticker reveal video....watch out for that #ComingSoon
The Ability to think is a priceless Asset, it’s great to see creative ways to flatten out some everyday speed bumps!
Thanks brother!
Nice job! You sure like living on the edge. If I tried that, the pin would have fallen ALL the way out. Worked well for you. Thanks for showing us a different way to "skin a cat".
😂 thanks brother
Man, that’s a nice car. I’d drive the wheels off of that thing. He should be very happy with all you’ve done.
Thanks buddy! Basically had to redo every system on it. Wiring next 😅
Always good to see someone so it the proper and correct way.
Thanks John! This was the best way I could come up with. 😅
Slick way of doing that with the bolt. I've pulled stuff like that with just the wire... tack it... dispense wire once grounded out, clip, curl in a loop, and pull that. Whatever works!
I barely had enough wire for 2 tacks! 👍🏼
Very slick trick! Glad you got it fixed up. Car sounds Awesome!!
Thanks Duddie! It’s coming together finally
Beautiful car! Great simple fix.
I guarantee that’s not in a book anywhere! 😂
Good job, Joe. I swear everything I own leaks! Very aggravating.
Gotta seal em up! I know it’s a pain!
Good job Joe.
Nice fix!
Engine sounds great.
Thank you, EM.
Thanks buddy!
Great fix sir!!!! Nice car!!!
Thanks brother! Y’all come see me 😉
Good job, but you forgot one thing, cutting the excess off those shackles! Ha just kiddin’. Great idea though. I don’t know if I would have thought of that!
Thanks Ron! I may slip the stockers back on for him.
#10 and 18 minutes fresh and I am going to enjoy over dinner. Great day to you JM Joe, hope you all have a great evening!
Have a good one brother!
I love the road runner, good job Joe.
Thanks brother! No burnouts. I don’t own this one. Lol
If you reach under the dash and unhook the speedo cable you can pull the center out and spray motorcycle cable lube or chain lube down the housing till it comes out at the trans and put the cable back in and connect back to the speedo. LOL, ask me how I know this.
I may have already asked, are you going to Bowling Green to Holley MOPARty this weekend? I'm going up Saturday.
I wish I was! Got some family stuff going on. I hope to make it someday!
Nice in car fix, excellent tip brother 👍
Poor folks have poor ways!😂
Another great fix !
Rob
Thanks Rob! Had to figure it out
Good idea on that pin o-ring.
It was going to be a pain! Worked out well! Thanks brother!
Nice work Joe!
Thanks buddy! I did not want to pull that pan again 😂
Dang it Joe! All that knocking under the car is where the heat from welding that bolt to the pin took the temper out of a rod bearing! It says so in the UA-cam comments, so it must be true!
😝
Looked like the check engine light was on…better scan it for codes 😄👍🇺🇸
😂 that bulb might accidentally burn out sometime soon
Good job on the transmission.
Thanks brother!
Nice work! I'm going to send you one of the greatest magnets ever, I have a bunch of them.
Please do! I would have tried it. Mine was a 3” magnet on stick. It wasn’t going
@@JustMoparJoe. They are used in a mag drive pump. When they are disposed of at work I split the magnet housing and pull the magnets. The best magnet I've used, I'll send one to ya.
@@RabidTransitGarage can’t wait! Thank you!
Good stuff dude!!! Looks like it gets on down pretty good!!!
It moves on out! It’s getting closer to scaring your dad in it! 😂
@@JustMoparJoe 🤭😂😁 I love that!
@@JustMoparJoe I'm hoping he wants to to put his 440 Cuda engine in it after a while, that would be a great video series..
Good thinking !
Thanks Brother!
You made that quick n simple!!
Thanks Bill! It took 4-5 hours, but the power of tv had it!
What mufflers are on that? Sounds great
The are longer dynomax see through style. I think 18” long.
@@JustMoparJoe cool thanks
sounded like baseball cards in the spokes cousin
And all the kids want them now!
Does this video have burnouts? A Gal shaped like a KFC bucket and a Ferry Boat ride? If not that cool lol
Stick around until next time I see Joe.....
@@johnwilburn lmfao
@@johnwilburn lmao....you know what's worse than a 30 Min air cleaner install video?....a 45 Min Sticker reveal video....watch out for that #ComingSoon
😂☠️
It’s got a Popeyes girl in this one
Spring shackles and Hurst/Gabriel air shocks. The only way to get N50's under a Satellite LOL
I may try to sneak some stockers back on for the owner 🤣
Wow pretty tedious awesome shortcut Joe
Thanks brother!
Yup, puttin it into a dry o-ring not a good idea. She don't normally like that.
Glad I stopped this one! My racetrack says, “it’s a Mopar, it’s going to leak somewhere.” 😅