Thank you so much! I learned I can shape carbon brushes. I had a couple laying around for years that finally found their purpose! Kind regards and happy 2024!
Thanks for the video. Suggest you add how to pop-off and re-install the end plate near the brushes. I'm guessing you "uncrimped" the edges of the cylinder housing, and then bent them back down a bit to re-install. Thanks again.
Automatic watering controller using Arduino/ uno board (Simple Project, No experience required) Please watch and share 👇👇👇🤗 ua-cam.com/video/EvBiTLfXPOo/v-deo.html
Hi Sir, your video has help me! I have a 14.4V battery drill and its carbon brush its not the typical kind with spring. And its not on the market. I followed your method and it works great! But perhaps you would know how to make the thinner part of the brush to be tight fit into the holder?
Please Click the Time Below: 1:58 Please use a file to make this tiny part. Measure the square hole size of Copper contacts and file the carbon as the same size. This has to be done very carefully and patiently.
I cant understand why don't they make it somewhat easily serviceable :(((( Aren't there at least the same brushes being sold or the only way is to make your own?
Bosch GSR 10.8v use rs550 dc motor, im waiting the dc motor from the store to replace the cordless impact drill bosch GDR 10.8v, do check my channel how to restore / replace the bosch cordless DC Motor. Thanks in advance
Please Click the Time Below: 1:58 Please use a file to make this tiny part. Measure the square hole size of Copper contacts and file the carbon as the same size. This has to be done very carefully and patiently.
This has to be done very carefully and patiently. You can find 4 locks at the back of the motor. Pull this locks up by using a nose plier or screwdriver or a punch. Once you have done this you will be able to remove the rear cover along with the connectors.
please click the link below ua-cam.com/users/redirect?q=https%3A%2F%2Fwww.banggood.in%2Fcustlink%2FvvG3Cm0Zk1&event=video_description&v=dEJVSvrUVTA&redir_token=nguqHjSDH_oPqobhg2fOlGiHVVx8MTU1NTY1MTc3NkAxNTU1NTY1Mzc2
Thank you so much! I learned I can shape carbon brushes. I had a couple laying around for years that finally found their purpose! Kind regards and happy 2024!
Awesome video. I am planing to replace worn out brushes for my motor. Also I will shot and upload video for such repiar.
i searched whole hyderabad and internet but couldnt find the same carbons. so i shaped the same carbons and fixed it. and it is working for now
Thanks for the video. Suggest you add how to pop-off and re-install the end plate near the brushes. I'm guessing you "uncrimped" the edges of the cylinder housing, and then bent them back down a bit to re-install. Thanks again.
Thank you now I can replace the carbon brush of my motor.
*Please Visit and Subscribe our UA-cam channel **ua-cam.com/users/Vtipcom** for more updates*
You are the best tks a million now need to find brushes but all shops close due to covid-19
This comment is true even after a year.
what do you think the problem is with my motor? it just clicks once inside when I try to start it.
Automatic watering controller using Arduino/ uno board (Simple Project, No experience required)
Please watch and share
👇👇👇🤗
ua-cam.com/video/EvBiTLfXPOo/v-deo.html
Nice helpful video.Congratulations
you helped me to repair my old and favorite cordless drill.... thanks bro..= like+sub...
Thanks
Got it...
Will just replace a whole motor
Bhai main na same trick ki but 5 mint k ander he carbon giz gaya or motor band ho hai kiya masalho sakta hai ya ?
सर आप जो ब्लॅक कलर का लगा रहे हो उसका नाम क्या है प्लीज बताईये
Hi Sir, your video has help me! I have a 14.4V battery drill and its carbon brush its not the typical kind with spring. And its not on the market. I followed your method and it works great! But perhaps you would know how to make the thinner part of the brush to be tight fit into the holder?
Please Click the Time Below:
1:58
Please use a file to make this tiny part. Measure the square hole size of Copper contacts and file the carbon as the same size. This has to be done very carefully and patiently.
I read your reply too late. It snapped out of the holder and grazed the armature badly 😅
😔
I cant understand why don't they make it somewhat easily serviceable :((((
Aren't there at least the same brushes being sold or the only way is to make your own?
cause they want you to buy a new drill instead of servicing the old or just go out and spend even more money to buy a brushless one.
Search eBay for rs775 brushes. They’re like $4
Thanks for this video. Does the replacement motor you gave in the link fit Bosch electric screwdriver model GSR 10.8v V-LI-2 ?
Don't Know, please check electrical screw driver motor specification with this motor. The shaft size may vary.🙂
Bosch GSR 10.8v use rs550 dc motor, im waiting the dc motor from the store to replace the cordless impact drill bosch GDR 10.8v, do check my channel how to restore / replace the bosch cordless DC Motor. Thanks in advance
Great job
how did you attach the new brushes? it doesn’t look like you glued them in or anything.
Kitne din chalega ye or ditne ghante ke baad change kr na padega ?
Bahut din chalega, use karne ki tarika me depend hoga!😇
Bhai main na same trick ki but 5 mint k ander he carbon giz gaya or motor band ho hai kiya masalho sakta hai ya ? Motor rs 550 hai
Sir ye varnan brush kaha se mila
Well done man
Very well done sir
great video.
Thank you 😊👍
tu idhar
You are great man
Thanks a lot 😌
Usually how long do the brushes last?
Depends
Pls mention the approximate hours
Thanks for making this tutorial, is 775 motor has cooling fan?
No
Yes
Kayak dinamonya bosch corless ya om?
I have used wired section carbon bush and my motor speed is slow
Speed and Torque slow ho gya
This carbon replace with soldering or glue??
No Soldering or Glue Used., It has a tiny lock system on the end of carbon brush.
Bro where will i get that carbon from ?? 🙏
How many hours does that carbon brushes last? 😳
Great job! But some motors are sealed.
remove the seal
Thanks man
Please make this video in detail please
Where did you buy that carbon brush?
Kitna din chalta hai yeh carbon
5days
Exellent
Thank you
Thanks
How did you shaped that carbon brush
Please Click the Time Below:
1:58
Please use a file to make this tiny part. Measure the square hole size of Copper contacts and file the carbon as the same size. This has to be done very carefully and patiently.
Hi, how do you open the motor?
This has to be done very carefully and patiently. You can find 4 locks at the back of the motor. Pull this locks up by using a nose plier or screwdriver or a punch. Once you have done this you will be able to remove the rear cover along with the connectors.
Thank you.
From where do you bought it please let me know
please click the link below
ua-cam.com/users/redirect?q=https%3A%2F%2Fwww.banggood.in%2Fcustlink%2FvvG3Cm0Zk1&event=video_description&v=dEJVSvrUVTA&redir_token=nguqHjSDH_oPqobhg2fOlGiHVVx8MTU1NTY1MTc3NkAxNTU1NTY1Mzc2
goodjob
Beli areng nya di mana om
In English please??
The brush where we buy
You can use any kind of carbon brush. You can see that in drill or grinder machines and mixer grinders.
nice
Thank you😊
Tangan e wong jowo kuwi... 🤣🤣🤣👍
Gajab
Thanks..
I dont know y iam watching this ..my 775 is still new
Good 😊
Tq bro
welcome
Bus ki Pati Tut Jaaye Kaise banaen
Greay
Good h
This is nice but you can buy cheap full assembly set online and no need to do that.
And what's the fun about it...
Kya baat hai
والله انت برنس
পুরে যাওয়া ১২ভলটের মটরকি করে ঠিক রবো
Can't understand!!!
ممحمممج.۹
کک