SF6 Circuit Breaker Part 1 Operation, Arc quenching inside interrupter with diagram explained

In this video, SF6 Circuit Breaker is discussed with respect to following points.
1. Identification of Components
2. Main and Arc contacts identification along with internal parts of interrupter
3. Close and Open operation with diagram
4. Arc quenching process
5. SF6 gas Properties
6. Arc Contact function and composition
For Business inquiries please mail to: [e-mail]
Video URL: • SF6 Circuit Breaker Pa...
#sf6circuitbreaker #sf6circuitbreakeroperation #sf6properties #sf6interrupter

[@Noah00008]

Thanks for your video! It's very helpful to me!

[@ElectroGlobe1]

Thank you for appreciation

[@bengalilonda3556]

Thanks for this video

[@klam77]

Fascinating. Great explanation even though it's robot voiceover.

[@ElectroGlobe1]

Thank you for the comment

[@pradeepraghavan2109]

VERY HELPFUL, THANKS FOR YOUR VIDEO

[@ElectroGlobe1]

Welcome

[@surendrakverma555]

Very good. Thanks

[@ElectroGlobe1]

Thanks you

[@DJCNU]

Thanks for video

[@ElectroGlobe1]

Thank you for appreciation

[@legendarygamerprince5317]

Thx for this video

[@ElectroGlobe1]

Welcome

[@bramhadeosawale9187]

Excellent

[@ElectroGlobe1]

Thank you sir for the comment

[@hamidmoulla4716]

Vers good

[@ElectroGlobe1]

Thank you for appreciation

[@chhayashinde82]

What happens when we try to extinguish arc, without weakening the arc or when arc is strong In ckt breaker #ratnadipshinde

[@lucioguevara-mendoza5096]

What happens when rupture disc breaks, breaker trips, and one or both poles remain energized? Would there be an internal fault with 0 SF6 pressure?

[@ElectroGlobe1]

If SF6 is at zero level. Any breaker operation whether close or open, should not be done in loaded condition. first load should be taken out of breaker circuit.

[@radosawhabdas7666]

Does the SF6 reading which you show on gauge shows the pressure in the gas tank itself or gas in whole CircuitBreaker chamber? Is there a difference to that?
What does high reading/low reading on it means? I read out that the leakage might lead to the gauge pressure reading dropping, but that would mean that the pressure outside of tank would rise?
What would the high reading indicate?

[@ElectroGlobe1]

SF6 pressure gauge shows the pressure inside circuit breaker. Low pressure means the pressure inside the breaker is dropped.

[@radosawhabdas7666]

@@ElectroGlobe1 Thanks for the fast response, so its not the pressure of the SF6 gas tank per se but the whole closed circuit in which the gas can cycle?
What happens when pressure of this gas increase? In what scenarios it could happen?

[@ElectroGlobe1]

@@radosawhabdas7666 Yes it indicates the pressure of complete gas pipes. High pressure than the recommended level can cause leakage.

[@raosadaqat2531]

sir we have gis system but there is some lekeage observed of sf6 gass from bus bar isolator compartment between breaker and isolator sir gas lekage observed from nutbolt what can ido now plz guide

[@ElectroGlobe1]

If SF6 gas pressure is dropping fast. Then is it better to turn off that particular compartment before SF6 level drops below permissible limit and leads to further complications. If SF6 pressure is not dropping fast and leakage is minor, then outage of the compartment at suitable time can be planned to attend the leakage. Though it is not possible to understand the problem completely stated, as it needs to understand other conditions at your system. Hope this helps.

[@muhammadhanif6399]

What is the reason for small glow light comes out of gis chamber?

[@ElectroGlobe1]

please elaborate the question

[@badassmoralfukka1]

Thank you, Stephen Hawking.

[@ElectroGlobe1]

Welcome

[@mohamedlakssoumi3439]

Or in CB

[@mohamedlakssoumi3439]

Why we use dc 110vDc in control box isolator plz

[@ElectroGlobe1]

110v DC in CB is used for closing and tripping coil pick up. Whenever closing or tripping command is given to CB, DC supply goes to coil and it magnetize coil. Also it is used for contacts pick up also. Hope this answered your query.

[@mohamedlakssoumi3439]

@@ElectroGlobe1 bro 110 Dc its used only in CB in substation ?and i thank you for this channel and for information i have more question but if you have a facebook or anything plz bro

[@ElectroGlobe1]

@@mohamedlakssoumi3439 Thank you for appreciation. As of now we are only on UA-cam. Soon we will be on other digital platforms. Same will be notified.

[@mohamedlakssoumi3439]

@@ElectroGlobe1 ok bro thx a lot for you time

[@mohamedlakssoumi3439]

@@ElectroGlobe1 bro can you tell me type of relay protection used in substation plz

[@michaelschuler7397]

Once arch is quenched arch is aimed at crotch moving crotch quenches contacts

[@jms019]

Sorry can’t stand the sound

[@ElectroGlobe1]

Working on sound quality

[@rbwernig]

Microfon is defect!

[@johnsmith-tr3dh]

5 min vid , how hard would it have been to get a person to narrate . Computer gen voice SUCKS